Dormakaba SIO-DR Manuale utente
WN 059731 45532 – 2019-04
EN
SIO-DR
Mounting instructions
1 About this document
1.1 Contents and purpose
This document describes the mounting of the SIO-DR
module.
1.2 Target group
This document is intended for assembling technicians
and specialists authorized for mounting by
dormakaba.
1.3 Other applicable documents
• Instructions for devices intended for networking
1.4 Symbols used
1. 2. Sequence of action steps
6Reference to a chapter
Components may be damaged by
electrostatic discharge. Ground
your own body before touching a
component!
2 Safety
2.1 Intended use
The SIO-DR module is used to connect analog switch
contacts to the dormakaba system bus. Messages are
output via contacts or control signals are read in.
2.2 Personnel qualification
Mounting may only be carried out by persons
authorized by dormakaba.
3 Product description
The SIO-DR module is a DCW® component. Status
messages are output potential-free via relays. Control
signals are read in via optocouplers.
The mounting takes place on a 35 mm DIN rail in
a housing. The housing must at least meet the
requirements of IP 30.
3.1 Parts included
106
92
65
Contents
1 About this document 1
2 Safety 1
3 Product description 1
4 Mounting 2
5 Disassembly and disposal 4
2SIO-DR 2019-04
WN 059731 45532
dormakaba Mounting instructions Mounting
4 Mounting
4.1 Mount the SIO-DR
5.1
J-Y(St)Y
2x2x0.8
1.
2.
1
2
1.
4.2 Assignment of terminals and switches
Out 1Out 2Out 3Out 4
GND 24V
NO
C
NC
NO
C
NC
NO
C
NC
NO
C
NC
GND 24V
DCW
In 1In 2 In 3 In 4 GND 24V1AB3
GND 24V1AB3
Addr
X500 X504
X502
X506X510X507X400
Out 1Out 2Out 3Out 4 GND 24V
NO
C
NC
NO
C
NC
NO
C
NC
NO
C
NC
GND 24V
DCW
In 1In 2 In 3 In 4 GND 24V1AB3
GND 24V1AB3
Addr
X500 X504X502
X506X510X507X400
Technical information
Supply voltage: 24VDC +/- 15 %
Power consumption:
- Quiescent current:
- Relay
For each active relay,
the current consumption
increases
by approx. 11 mA
7 mA
Relay 1 active 18 mA
Relay 1+2 active 29 mA
Relay 1+2+3 active 40 mA
Relay 1+2+3+4 active 51
mA
Ambient temperature: -10 °C to +55 °C
Rel. humidity: up to 93 % (non
condensing)
Protection class: dependent on the housing
used
Inputs
In 1 to In 4
(optocoupler)
Current consumption of
inputs per input:
at 5V AC/DC: 3mA
at 12V AC/DC: 8mA
at 24V AC/DC: 17mA
at 28V AC/DC: 28mA
Contact load capacity: 24 V, 1 A current carrying
capacity
3.2 LED displays
DCW
LED on LED off LED flashes
Bus connection OK
Power supply or DCW® bus
connection disturbed
Bus connection interrupted
(not Safe DCW® node)
3SIO-DR 2019-04WN 059731 45532
dormakaba Mounting instructions Mounting
X400 +24VDC
GND
DCW® bus
X502 GND
GND
+24VDC
+24VDC
Output for external loads
(max. 1A, depending on the power supply)
X507 GND
GND
+24VDC
+24VDC
Output for external loads
(max. 1A, depending on the power supply)
X500
Out1
Out2
Contact load capacity: 24V, 1A
Contact load capacity: 24V, 1A
Pre-alarm (door open)
Main alarm (door open)
Parameterizable
via TMS Soft®.
For multi-door
systems
Out 1 to Out 4 are
assigned to the
corresponding
door addresses 1
to 4.
X504
Out3
Out4
Contact load capacity: 24V, 1A
Contact load capacity: 24V, 1A
Emergency button
pressed
Locked
X506 In1
In2
Optocoupler 5-28VAC/DC
Optocoupler 5-28VAC/DC
Temporary unlocking Ü1
Long-term unlocking Ü1
Parameterizable
via TMS Soft®.
In multi-door
systems In 1 to In
4 are assigned to
the corresponding
door addresses 1
to 4.
X510 In3
In4
Optocoupler 5-28VAC/DC
Optocoupler 5-28VAC/DC
Permanent unlocking
Lock
Address Switch
1
ON 1
0
2
1
2
3
4
0
1
0
1
0
0
1
1
DCW® DIP switch
If several SIO-DR modules are connected via the DCW® bus, assign different DCW® bus
addresses to the SIO-DR modules.
dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: +49 2333 793-0 F: +49 2333 793-4950 www.dormakaba.com
Translation of the original document, subject to change without notice
5 Disassembly and disposal
Disassembly is carried out in the reverse order of
mounting and must be carried out by qualified
personnel.
The product must be disposed of in an
environmentally friendly manner. Electro-
technical parts and batteries must not be
disposed of as domestic waste. Dispose of
electrotechnical parts and batteries in the designated
acceptance and collection points. Refer to the
statutory regulations for your country.
Altri manuali Dormakaba Unità di controllo
Dormakaba
Dormakaba LA GARD 700 Series Manuale utente
Dormakaba
Dormakaba SafeRoute SCU-UP Manuale utente
Dormakaba
Dormakaba MotionIQ ED-CAN Manuale utente
Dormakaba
Dormakaba MFC Manuale utente
Dormakaba
Dormakaba SLI-A Interlock Manuale utente
Dormakaba
Dormakaba UNIQUIN Manuale utente
Dormakaba
Dormakaba SCU-DR Guida utente
Dormakaba
Dormakaba ED connection board CAN Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
