Eaton Modbus MS Card Manuale utente

www.eaton.com

Modbus MS

Card

User manual

Modbus MS Card –User Manual 34009048XT_EN/AD Page 1/55

Modbus MS Card –User Manual 34009048XT_EN/AD Page 2/55

Contents

1INTRODUCTION 4

2PRESENTATION 5

2.1 OVERVIEW 5

2.2 FUNCTIONS 5

2.3 TECHNICAL CHARACTERISTICS 6

3INSTALLATION 7

3.1 RS232 LINK CONFIGURATION AND CONNECTION 7

3.2 RS485 LINK CONFIGURATION AND CONNECTION 8

3.2.1 RS485 connection 8

3.2.2 RS485 link configuration for 2 wires connexion 10

3.2.3 RS485 link configuration for 4 wires connexion 12

3.3 CONFIGURATION OF THE JBUS/MODBUS COMMUNICATION PARAMETERS 14

3.3.1 Choice 1: Display Jbus settings 15

3.3.2 Choice 2: Modify Jbus settings 15

3.3.3 Choice 3: Display Jbus diagnostics 16

3.3.4 Choice 4: Reset Jbus diagnostics 16

3.3.5 Choice 5: Return to Jbus Default Configuration 16

3.3.6 Choice 6: Display Jbus frames 16

4ADDITIONAL WEB PAGES 18

5MENU/CLI INTERFACES 19

5.1 MENU INTERFACE 19

5.1.1 Main menu 19

5.1.2 Modbus/Jbus menu 19

5.2 COMMAND LINE INTERFACE 21

5.2.1 “getJBUS” 21

5.2.2 “setJBUS” 21

5.2.3 “getJBUSCounter” 22

5.2.4 “setJBUSCounter” 22

6JBUS TABLE 23

6.1 DATA FOR PULSAR 700 /1000 /1500 23

6.1.1 Status table 23

6.1.2 Measurements table 24

6.2 DATA FOR PULSAR M2200 /3000 25

6.2.1 Status table 25

6.2.2 Measurements table 26

6.3 DATA FOR PULSAR MX 4000 /5000 /10000 27

6.3.1 Status table 27

6.3.2 Measurements table 28

6.4 DATA FOR PULSAR MX FRAME 15 /20 29

Modbus MS Card –User Manual 34009048XT_EN/AD Page 3/55

6.4.1 Status table 29

6.4.2 Modular fault table 30

6.4.3 Measurements table 32

6.5 DATA FOR EATON 93E AND EATON 93PM 34

6.5.1 Status table 34

6.5.2 Measurements table 35

6.6 DATA FOR EATON 5PX AND EATON 5P 37

6.6.1 Status table 37

6.6.2 Measurements table 38

6.7 DATA FOR EATON 9E 39

6.7.1 Status table 39

6.7.2 Measurements table 40

6.8 DATA FOR EATON 9PX AND EATON 9SX SINGLE PHASE 41

6.8.1 Status table 41

6.8.2 Measurements table 42

6.9 DATA FOR EATON 9PX THREE PHASE INPUT 43

6.9.1 Status table 43

6.9.2 Measurements table 44

6.10 DATA FOR EATON 9PX SPLIT PHASE 45

6.10.1 Status table 45

6.10.2 Measurements table 46

6.11 GENERIC UPS 47

6.11.1 Status table 47

6.11.2 Measurements table 49

6.12 SENSOR DATA 51

6.12.1 Status table 51

6.12.2 Measurements table 52

6.12.3 Read of the personalization table 53

6.13 OTHER DATA 54

7GLOSSARY 55

Modbus MS Card –User Manual 34009048XT_EN/AD Page 4/55

1 Introduction

The embedded application of the Modbus MS Card (previously INMC) is based on the Network MS Card (previously NMC).

For all common features, the user manual is the same as NMC (see reference below).

In this document, only JBUS/MODBUS requirements are described.

Reference

Network Management Card –User Manual 34003990XT_FR/EF

Modbus MS Card –User Manual 34009048XT_EN/AD Page 5/55

2 Presentation

2.1 Overview

2.2 Functions

The Modbus MS Card provides the same functions than the Network MS card described in the previous section of this

document.

The adding function consists to provide UPS (Uninterruptible Power Supply) data (states and measures) to be sent a computer

system.

The JBUS hexadecimal (MODBUS RTU) communication protocol is used in slave mode. The system provides a

communication channel with an RS485 or RS232 interface.

Note:

2 wires or 4 wires RS485 link are available.

Warning:

RS232 and RS485 communication ports cannot be used together.

JBUS/MODBUS communication is operational 2 minutes after the startup of the card.

Modbus MS Card –User Manual 34009048XT_EN/AD Page 6/55

2.3 Technical characteristics

Functions

Parameters

Default values

Possible values

JBUS/MODBUS

communication

- Baud rate

- Parity

- Bit number

- Stop bit

- Slave number

- 9600 bauds

- without parity

- 8

- 2

- Slave nr 1

- 1200, 2400, 4800, 9600, 19200, 38400

- Without parity, even parity, odd parity

- 1, 2

- 1 to FF (hexadecimal)

RS232 link

- Link connection in

transmit data (Tx) or

receive data (Rx)

- Rx on pin 1

- Tx on pin 3

- Rx on pin 1

- Tx on pin 3

RS485 link

- Termination

- No termination

- With or without (2 or 4 wires)

Modbus MS Card –User Manual 34009048XT_EN/AD Page 7/55

3 Installation

3.1 RS232 link configuration and connection

Set the SA2 switches like below:

The next figure shows the details of the connection in RS232 mode:

JBUS/232/485

OV T+ T- R+ R- UPS Data

Settings/SensorETHERNET

100MACT RS232

Tx Rx

125 4 3

XXXXXXXXXXXX 66103

Pin number

Function

Received data (input)

Not connected

Transmitted data

(output)

Not connected

Signal Ground

Modbus MS Card –User Manual 34009048XT_EN/AD Page 8/55

3.2 RS485 link configuration and connection

3.2.1 RS485 connection

Normally, the master of the network sets the polarity of the line. The Modbus MS card is a slave equipment and don’t have

polarisation resistor.

The two ends of the line must be terminated. Allow for 1 or 2 terminators to avoid mismatching the line when any equipment at

the end of the line is disconnected.

The next figure gives the detail of the RS485 connector and the internals drivers:

Pin number

Function

R- : Receiver - (input)

R+ : Receiver + (input)

T- : Transmitter - (output)

T+ : Transmitter +

(output)

0 V

Important notes:

Use twisted pair cable (cable specification 0.3mm2 and capacitance 42pF/m)

The transmission range will increase if a cable with lower capacitance and larger diameter is used.

Use shielded cable in heavy industrial environments.

Modbus MS Card –User Manual 34009048XT_EN/AD Page 9/55

The settings of the RS485 link are made through the SA1 switches:

SA1 description:

1: reserved

2: reserved

3: link termination between T- to R- (2 wires configuration) if set to ON

4: connection T- to R- (2 wires configuration) if set to ON

5: connection T+ to R+ (2 wires configuration) if set to ON

6: reserved

7: reserved

8: link termination between R+ and R- if set to ON

Modbus MS Card –User Manual 34009048XT_EN/AD Page 10/55

3.2.2 RS485 link configuration for 2 wires connexion

Set the SA2 switches like below to set the RS485 mode:

Set the SA1 switches to select the two wires configuration with no termination:

Indice

Altri manuali Eaton Scheda di rete

Eaton

Eaton Network Management Card Manuale utente

Eaton

Eaton Power Xpert Meter 2000 Manuale utente

Eaton

Eaton DeviceNet Starter Network Adapter D77B-DSNAP Manuale utente

Eaton

Eaton PXGMS Power Xpert Gateway Minislot UPS Manuale utente

Eaton

Eaton Network-MS Manuale utente

Eaton

Eaton POW-R-COMMAND 1000 Manuale utente

Eaton

Eaton DeviceNet Product Operated Network Interface Manuale

Eaton

Eaton Network Card-MS Manuale utente

Eaton

Eaton Network-M2 Manuale utente

Eaton

Eaton -66103 Manuale utente

Eaton

Eaton Network Card-MS Manuale utente

Eaton

Eaton Powerware Series Manuale di programmazione

Eaton

Eaton 34003991EN/EB Manuale utente

Eaton

Eaton Network-M2 Manuale utente

Eaton

Eaton Network-M3 Manuale utente

Eaton

Eaton QSNAP Manuale utente

Manuali Scheda di rete popolari di altre marche

FirstComm

FirstComm OBiWiFi5G Manuale utente

Sun Microsystems

Sun Microsystems Interface Adapter Manuale utente

TRENDnet

TRENDnet TU2-ETG Manuale utente

YASKAWA

YASKAWA SI-EN3 Manuale utente

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Belkin

Belkin F5D7050 Manuale utente

3Com

3Com EtherLink 3C509B Manuale utente

TRENDnet

TRENDnet TEG-PCITX Manuale utente

Cisco

Cisco MC16E Manuale utente

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuale utente

TwinMOS

TwinMOS Booming Manuale utente

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuale utente

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuale utente

National Instruments

National Instruments NI 9234 Manuale utente

Hama

Hama 49276 Manuale utente

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo

Compaq

Compaq Wireless LAN 100 Manuale utente

Bose

Bose PowerMatch Dante Manuale utente