Edge-Core ECS2100-10P Manuale utente

– 1 –

Quick Start Guide

10/28-Port Web-Smart Pro Gigabit Ethernet Switch

ECS2100-10T/ECS2100-10P/ECS2100-10PE

ECS2100-28T/ECS2100-28P/ECS2100-28PP

The ECS2100 series switches include the following models:

ECS2100-10T— 8 10/100/1000BASE-T + 2 SFP uplink ports

ECS2100-10PE— 8 10/100/000BASE-T + 2 SFP uplink ports (4 PoE ports)

ECS2100-10P— 8 10/100/1000BASE-T + 2 SFP uplink ports (8 PoE ports)

ECS2100-28T— 24 10/100/000BASE-T + 4 SFP uplink ports

ECS2100-28P— 24 10/100/000BASE-T + 4 SFP uplink ports (24 PoE ports)

ECS2100-28PP— 24 10/100/000BASE-T + 4 SFP uplink ports (24 PoE ports)

OTE

The ECS2100 series switches are for indoor use only.

OTE

For Safety and Regulatory information, refer to the Safety and Regulatory

Information document included with the switch.

ECS2100-10PE

ECS2100-10P

ECS2100-10T

ECS2100-28P

ECS2100-28PP

ECS2100-28T

E012016-AP-R01

150200001318A

www.edge-core.com

Quick Start Guide

– 2 –

1. Unpack the Switch Unpack the switch and check the package contents.

◆ECS2100-10T, ECS2100-10P, ECS2100-10PE, ECS2100-28T, ECS2100-28P or

ECS2100-28PP Web-Smart Pro Gigabit Ethernet Switch

◆Rack Mounting Kit containing two standard brackets and eight screws

◆4 adhesive foot pads

◆Power cord— either US, Continental Europe or UK

◆Quick Start Guide

◆Regulatory and Safety Information

Optional Item

◆Console cable—RJ-45 to DB-9

Note:

For other documentations include Installation Guide, Web Management

Guide, and CLI Reference Guide can be obtained from www.edge-core.com ->

support -> download -> user manual.

2. Install the Switch Rack Mounting

The switch can be mounted in a standard 19-inch rack or on a desktop or shelf.

Following your rack plan, mark the holes in the rack where the switch will be

installed. Lift the switch into the rack and hold it in a position aligned with the

marked holes. Secure the switch in the rack, using four rack-mounting screws (not

provided).

Wall Mounting (ECS2100-10PE only)

The ECS2100-10PE can be mounted on a wall.

Caution:

For safe operation, install the switch with RJ-45 ports facing up.

Attach the brackets to the switch.

Use the screws supplied with the rack to secure the switch in the rack.

Quick Start Guide

– 3 –

3. Ground the Switch Before powering on the switch, ground the switch to earth.

Ensure the rack on which the switch is to be mounted is properly grounded and in

compliance with ETSI ETS 300 253. Verify that there is a good electrical connection

to the grounding point on the rack (no paint or isolating surface treatment).

Caution:

The earth connection must not be removed unless all supply

connections have been disconnected.

4. Connect Power Connect the switch to an AC power source to power on. Verify that the external AC

power requirements for the switch can be met as listed below:

ECS2100-10T: AC 100-240 V, 50-60 Hz, 0.5 A

ECS2100-10P: AC 100-240 V, 50-60 Hz, 2.1 A

ECS2100-28T: AC 100-240 V, 50-60 Hz, 0.5 A

ECS2100-28P: AC 100-240 V, 50-60 Hz, 3.2 A

ECS2100-28PP: AC 100-240 V, 50-60 Hz, 5.8 A

Caution:

Before connecting the switch to AC power, the grounding terminal screw

on the switch rear panel must be connected to earth.

Set two screws in the wall 150 mm (5.9 in.) apart.

Slide the switch’s wall mounting slots down onto the screws so that the unit is secure.

Connect a grounding wire and lug to the grounding point on the switch rear panel, and then

to rack ground.

Quick Start Guide

– 4 –

The ECS2100-10PE includes an AC-DC power adapter. Connect the AC-DC power

adapter to the switch and to an AC power source. The AC-DC adapter provides

54 VDC, 1.67 A of power to the switch.

Caution:

Before connecting the switch to DC power, the grounding terminal

screw on the switch rear panel must be permanently connected to earth.

5. Verify Switch

Operation

Verify basic switch operation by checking the system LEDs.

When operating normally, the Diag and Power LEDs should both be on green.

Plug the AC power cord into the socket on the rear of the switch.

Plug the DC power cable into the socket on the rear of the switch.

Plug the AC-DC power adapter into a nearby AC power outlet.

System Status LEDs.

Quick Start Guide

– 5 –

6. Make Initial

Configuration

Changes

At this point, you may need to make a few basic switch configuration changes

before connecting to the network. you can either connect to the switch console

port or any RJ-45 port to perform this task.

Through an RJ-45 Port

The switch offers a user-friendly web-based management interface for the

configuration of all the unit’s features.

You can make initial configuration changes by connecting a PC directly to one of

the switch’s RJ-45 ports. The switch has a default management IP address of

192.168.2.10 and a subnet mask of 255.255.255.0. You must set your PC IP address

to be on the same subnet as the switch (that is, the PC and switch addresses must

both start 192.168.2.x).

◆Login Name — admin

◆Password — admin

Through the Console Port

The serial port’s configuration requirements are as follows: 115200 bps, 8

characters, no parity, one stop bit, 8 data bits, and no flow control.

You can log in to the command-line interface (CLI) using default settings: User

“admin” with password “admin”.

For information on initial switch configuration, refer to the CLI Reference Guide.

Console Port.

Console Cable. (Cable not included)

Quick Start Guide

– 6 –

7. Connect Network

Cables

Install SFP transceivers and connect network cables to port interfaces:

◆For RJ-45 ports, use 100-ohm Category 5, 5e or better twisted-pair cable for

1000BASE-T connections, Category 5 or better for 100BASE-TX connections,

and Category 3 or better for 10BASE-T connections.

◆First install SFP transceivers and then connect fiber optic cabling to the

transceiver ports. The following transceivers are supported:

■1000BASE-SX (ET4201-SX)

■1000BASE-LX (ET4201-LX)

■1000BASE-ZX (ET4201-ZX)

As connections are made, check the port status LEDs to be sure the links are valid.

8. (Optional) Extend

PoE Budget to 740W

(ECS2100-28PP only)

If you have purchased an optional Extended Power Supply (EPS460W) and Chassis

(PS3000), follow the instructions below to connect it to the ECS2100-28PP and to

AC power.

Note:

The ECS2100-28PP default PoE power budget is 370 W, by purchasing an

Extended Power Supply kit, the ECS2100-28PP can extend its PoE power budget up

to 740W.

10/100/1000BASE-T RJ-45 Port.

Twisted-pair Cable with RJ-45 Plug.

Quick Start Guide

– 7 –

Note:

For International use, you may need to change the AC line cord. You must

use a line cord set that has been approved for the socket type in your country.

Extended Power Supply—EPS460W

Install the ECS2100-28PP in a standard 19-inch rack and power on.

Install the PS3000 chassis in a standard 19-inch rack.

Install one or more EPS460W PSUs in the chassis. The chassis can support up to three EPS460W

PSUs.

Use the PSU cable (provided) to connect each EPS460W PSU to an ECS2100-28PP switch.

Connect the AC power cord to power on the EPS460W PSU, and check the LEDs on the PSUs to

ensure proper operation. The Link LEDs for connected switches should light up.

Quick Start Guide

– 8 –

Hardware Specifications

Item Specification

Chassis Specifications

Size (W x D x H):

ECS2100-10T: 19.64 x 11.71 x 3.66 cm (7.73 x 4.61 x 1.44 in.)

ECS2100-10P: 33.0 x 20.4 x 4.26 cm (12.99 x 8.03 x 1.67 in.)

ECS2100-10PE: 24.0 x 15.5 x 2.65 cm (9.44 x 6.10 x 1.04 in.)

ECS2100-28T/28P/28PP: 44 x 22 x 4.4 cm (17.32 x 8.66 x 1.73 in. )

Weight ECS2100-10T: 816 g (1.8 lb)

ECS2100-10P: 2.4 kg (5.34 lb)

ECS2100-10PE: 973 g (2.15 lb)

ECS2100-28T: 2.2 kg (4.86 lb)

ECS2100-28P: 2.8 kg (6.18 lb)

ECS2100-28PP: 3.1 kg (6.85 lb)

Temperature Operating: 0 ° C to 50 ° C (32 ° F to 122 ° F)

Operating: 0 ° C to 40 ° C (32 ° F to 104 ° F, ECS2100-10P only)

Storage: -40 ° C to 70 ° C (-40 ° F to 158 ° F)

Humidity Operating: 10% to 90% (non-condensing)

Power Specifications*

* Maximum power consumption values are measured under a 100 percent loading test and

should be used as estimates for planning purposes.

AC Input Power ECS2100-10T: AC 100-240 V, 50-60 Hz, 0.5 A

ECS2100-10P: AC 100-240 V, 50-60 Hz, 2.1 A

ECS2100-28T: AC 100-240 V, 50-60 Hz, 0.5 A

ECS2100-28P: AC 100-240 V, 50-60 Hz, 3.2 A

ECS2100-28PP: AC 100-240 V, 50-60 Hz, 5.8 A

AC-DC Power Adapter

(ECS2100-10PE only)

Input: AC 100-240 V, 50-60 Hz, 1 A

Output: 54 VDC, 1.67A

Total Power Consumption ECS2100-10T: 8 W

ECS2100-10P: 160 W

ECS2100-10PE: 80 W

ECS2100-28T: 20 W

ECS2100-28P: 260 W

ECS2100-28PP: 490 W

ECS2100-28PP+ one extended power supply: 950 W

Regulatory Compliances

Emissions CE Mark

◆EN 55022, Class A

FCC Class A

BSMI Certificate

Immunity IEC 61000-3-3, 61000-4-2/3/4/5/6/11

Safety UL/CUL(UL60950-1, CSA60950-1)

CB (IEC60950-1)

CSA/NRTL (UL60950, CSA 22.2.No 60950)

EN 60950-1:2006+A11:2009+A1: 2010+A12:2011+A2:2013 / IEC 60950-

1:2005; Am1:2009; CSA22.2 No. 60950-1-07 2nd; UL 60950-1 2nd

CB (IEC/EN 60950-1)

Altri manuali per ECS2100-10P

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Edge-Core Interruttore

Edge-Core

Edge-Core ECS4310-18T Manuale utente

Edge-Core

Edge-Core AS7726-32X Manuale utente

Edge-Core

Edge-Core AS4610-30T Manuale utente

Edge-Core

Edge-Core ECS5610-52S Manuale utente

Edge-Core

Edge-Core ECS2100-10T Manuale utente

Edge-Core

Edge-Core ES4528V-38 Manuale di programmazione

Edge-Core

Edge-Core ECS4130-28T Manuale utente

Edge-Core

Edge-Core ES3628EA Manuale utente

Edge-Core

Edge-Core ECS2100-10T Manuale utente

Edge-Core

Edge-Core ES3526VA-PoE Manuale utente

Edge-Core

Edge-Core ECS4610-24F Manuale di programmazione

Edge-Core

Edge-Core ECS3510-10PD Manuale di programmazione

Edge-Core

Edge-Core AS4600-54T Manuale utente

Edge-Core

Edge-Core ES4524D Manuale utente

Edge-Core

Edge-Core ECS4810-12M-EUK Manuale utente

Edge-Core

Edge-Core ECS5520 Series Manuale utente

Edge-Core

Edge-Core ECS4620-28T Manuale utente

Edge-Core

Edge-Core ES4308-POE Manuale di programmazione

Edge-Core

Edge-Core ECS2100-10T Manuale utente

Edge-Core

Edge-Core ECS4620-28T Manuale utente

Edge-Core

Edge-Core ES4308-POE Manuale di programmazione

Edge-Core

Edge-Core ECS4620-28P Manuale di istruzioni

Edge-Core

Edge-Core ES4704BD Manuale utente

Edge-Core

Edge-Core ECS1100-5P Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente