Edimax ES-3116RL Manuale utente
0
16 / 24 Ports
F
Fa
as
st
t
E
Et
th
he
er
rn
ne
et
t
S
Sw
wi
it
tc
ch
he
es
s
1
19
9”
”
R
Ra
ac
ck
km
mo
ou
un
nt
t
Q
Qu
ui
ic
ck
k
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
G
Gu
ui
id
de
e
1
FCC Certifications
This Equipment has been tested and found to comply with the limits for a
ClassAdigital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interferencewhen
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 classAfor ITE, the essential protection requirement
of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check with
your local distributors for the latest information. No part of this document can
be copied or reproduced in any form without written consent from the
company.
Trademarks:All trade names and trademarks are the properties of their
respective companies.
Copyright © 2005, All Rights Reserved.
2
English.
Introduction
This device is a powerful, high-performance Fast Ethernet
switch, with all ports capable of 10 or 100Mbps auto-negotiation
operation (NWay), which means this switch could automatically
negotiate with the connected partners on the network speed and
duplex mode. It is ideal for micro-segmenting large networks into
smaller, connected subnets for improved performance, enabling
the bandwidth demanding multimedia and imaging applications.
Moreover, the 10/100Mbps auto-sensing ability provides an
easy way to migrate 10Mbps to 100Mbps network with no pain.
Compared to the shared 10Mbps or 100Mbps networks, the
switch delivers a dedicated 10/100Mbps connection to every
attached client with no bandwidth congestion issue. This switch
also supports auto MDI / MDI-X function; each port could be
used to connect to another switch or hub with no crossover
RJ-45 cable.
Store-and-forward switching mode promises the low latency
plus eliminates all the network errors, including runt and CRC
error packets. To work under full-duplex mode, transmission and
reception of the frames can occur simultaneously without
causing collisions as well as double the network bandwidth.
The switch is plug-n-play without any software to configure and
also fully compliant with all kinds of network protocols. Moreover,
the rich diagnostic LEDs on the front-panel can provide the
operating status of individual port and whole system.
Before you start to install the switch, check the following
contents in this package：
zOne Rackmount Fast Ethernet Switch
zOne power cord and one user’s manual
zRack-mount brackets and screws
3
LED Definition
Please refer to the following table for LED definition
24 Ports example
LED Status Operation
Steady Green Power is on
Power Off Power is off
Steady Green The port is connected
Blinking Green The port is
transmitting/receiving data.
Link/Act
Off No connection
Stations Connection
Connect each station to the switch by twisted-pair cable. Plug
one RJ-45 connector into a RJ-45 port of the switch, and plug
the other RJ-45 connector into the station’s network adapter.
Power on the switch and then system is ready. For cable
selection, refer to the following table.
Switches Connection
In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As all
the ports support auto MDI / MDI-X function, using a straight
cable to make a switch-to-switch connection is allowed.
4
For cable selection, refer to the following table：
Network Speed Cable Type Max. Length
10Mbps Cat. 3, 4, 5 UTP/STP 100 meters
100Mbps Cat. 5 UTP/STP 100 meters
Rack-Mount
The switch may standalone, or may be mounted in a standard
19-inch equipment rack. Rack mounting produces an orderly
installation when you have a number of related network devices.
The switch is supplied with two optional rack mounting brackets
and screws. These are used for rack mounting the unit.
Specification
Standard
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x full duplex operation and
flow control
Interface 16/ 24 * 10/100Mbps RJ-45 Fast
Ethernet Ports
Uplink Auto MDI/MDI-X(Auto crossover)
Network Speed 10/100Mbps & Full/Half duplex mode
auto detection
MAC Addr. Table 8K MAC entries
Memory 160Kbytes
Power Supply Internal Power supply
3.3V 4A (100-240V/ 50-60Hz)
EMI CE and FCC class A
Altri manuali per ES-3116RL
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Edimax Interruttore
Edimax
Edimax ES-5804PH Manuale utente
Edimax
Edimax ES-5816P Guida di riferimento
Edimax
Edimax GS-1016 Manuale utente
Edimax
Edimax ES-516G+ Manuale utente
Edimax
Edimax EK-PAK2 Manuale utente
Edimax
Edimax SP-1101W Manuale utente
Edimax
Edimax ES-5500P Manuale utente
Edimax
Edimax ES-3205P Manuale utente
Edimax
Edimax ES-3305P Manuale utente
Edimax
Edimax 5/8 Ports Desktop Manuale utente
Edimax
Edimax EK-UAK2 Guida di riferimento
Edimax
Edimax ES-3208P Manuale utente
Edimax
Edimax ES-5808PHG Manuale utente
Edimax
Edimax ES-5500M V2 Manuale utente
Edimax
Edimax ES-5816P Manuale utente
Edimax
Edimax ES-5816PHG Manuale utente
Edimax
Edimax GS-5008E Manuale utente
Edimax
Edimax EK-UA2C Manuale utente
Edimax
Edimax EK-2U2C Manuale utente
Edimax
Edimax EU-HB4S Manuale utente
