Edimax ES-5808P Manuale utente
User Manual
ES-5808P
8 Ports 10M/100M Desktop PoE
Web Smart Fast Ethernet Switch
FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. It may
cause harmful interference to radio communications if the equipment is not installed
and used in accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
1
Content
Content 1
Introduction 2
Hardware Description 5
User Log In 7
Administrator 8
Port Management 13
VLAN Setting 17
Per Port Counter 21
QoS Setting 22
Security 24
Spanning Tree 26
Trunking 29
Backup/Recovery 30
Miscellaneous (IGMP) 31
Logout 32
2
Introduction
Product Overview
This 8 ports 10/100 Mbps PoE web-smart switch includes auto-MDI/MDIX
crossover detection function. 8 of those ports are all built with PoE functionality,
providing the ultimate choice in network flexibility. With this added PoE feature,
this switch is an ideal solution for building wireless, IP surveillance, and VoIP
networks.
This 8 ports web-smart PoE switch provides a port-based and 802.1Q tag
VLAN function to provide better traffic management, reduce latency, improve
security and save bandwidth. This is also a cost-saving feature as it reduces
the need to add additional hardware to the network.
The switch has 8 10/100BASE-TX ports that support the IEEE 802.3af PoE
protocol. Each port and transmit a maximum power 15.4 watts. User can also
enable or disable power supply on PoE ports from UI.
Web Management Features
Port Management
Port Configuration
Port Mirroring
Bandwidth Control
Broadcast Strom Control
PoE On/Off Setting
VLAN Setting
Port-based/ Tag-based
VLAN ID: 1~4094
Trunking
Link Aggregation Setting
2 groups (1~4 port for each group)
QoS Setting
Priority Mode
Class of Service Configuration
TCP/UDP Port-based
Security Setting
MAC address filtering
3
TCP/UDP Port filtering
STP/RSTP
Spanning Tree Protocol
Backup Recovery Configuration
Specifications
Standard
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
IEEE 802.3x Full-duplex and Flow Control
IEEE 802.af PoE
IEEE 802.3ad Link Aggregation
IEEE 802.1d Spanning tree protocol
IEEE 802.1w Rapid Spanning tree protocol
IEEE 802.1x Port-based Network Access Control
IEEE 802.1Q VLAN
IEEE 802.1p Class of Service
Number of Port
8-port 10/100BaseTX with PoE (Full power)
Mechanical
LED Indicator
Per Port: Link/ Act
PoE Port: Act/Status
Per Unit: Power
Power Consumption: 130Watts (Max)
Power Input: 100~240V/AC, 50~60HZ
Power Output: 48V/DC per Port Output –15.4W Max per Port
Product Dimensions/ Weight
266 × 160 × 44 mm (L × W ×H) / 1.6kg
Performance
MAC Address: 4K
4
Buffer Memory: 1.625Mb
Transmission Method: Store and Forward
Package Contents
Before you start to install this switch, please verify your package that
contains the following items:
One Fast Ethernet PoE Switch
One Power Cord
A User Manual CD
5
Hardware Description
This section mainly describes the hardware of the 8 PoE port Ethernet Combo
Web-Smart Switch and gives a physical and functional overview on the certain
switch.
Physical Dimensions/ Weight
260 × 160 × 44 mm (L × W × H) / 1.6kg
Front Panel
The front Panel of the Web Managed Switch consists of 8 10/100Base-TX
RJ-45 ports. The LED Indicators are also located on the front panel.
LED Indicators
The LED Indicators present real-time information of systematic operation
status. The following table provides description of LED status and their
meaning.
Table 1-1 LED Indicators
LED
Status
Description
Power
On
Power is on.
Off
Power is off.
Blink
Reset Button for 3 seconds
PoE
On
Port is Linked to Power Device
Off
No Power Device is connected
Link/Act
On
The port works in 10/100M
Blinks
(continuously)
Networking is active
Off
No device attached
LED
Display
RJ-45 Port
6
Rear Panel
The 3-pronged power plug is placed at the rear panel of the switch right side
shown as below.
Hardware Installation
Set the switch on a large flat space with a power socket close by. The flat
space should be clean, smooth, level and sturdy. Make sure there is enough
clearance around the switch to allow attachment of cables, power cord and
allow air circulation. The last, use twisted pair cable to connect this switch to
your PC then user could start to operate the switch.
7
User Log In
This part instructs user how to set up and manage the switch through the web
user interface. Please follow the description to understand the procedure.
At the first, open the web browser, and go to 192.168.2.1 site then the user will
see the login screen. Key in the password to pass the authentication then
clicks the OK.The log in process is completed and comes out the sign
“Password successfully entered”.
Log in
ID: admin
Password: 1234
Figure 1-1-1
※Note: It will show error message if you key in wrong user name or password.
Figure 1-1-2
Main Page
Figure 1-2
8
Administrator
Authentication Configuration
This page shows authentication configuration information. User can set new
Username and Password in this page.
Figure 1-3
System IP Configuration
This page shows system configuration including the current IP address and
sub-net mask and gateway.
Figure 1-4
User can configure the IP settings, Subnet Mask, Gateway as below:
IP address: Manually assign the IP address that the network is using. The
default IP is 192.168.2.1
Subnet Mask: Assign the subnet mask to the IP address.
Gateway: Assign the network gateway for industrial switch. The default
Altri manuali per ES-5808P
1
Indice
Altri manuali Edimax Interruttore
Edimax
Edimax ES-1016 Manuale utente
Edimax
Edimax EU-4306 Manuale utente
Edimax
Edimax USBH-004 Manuale utente
Edimax
Edimax ES-5500P Manuale utente
Edimax
Edimax GS-5654LX Manuale utente
Edimax
Edimax EK-UAK2 Manuale utente
Edimax
Edimax ES-5824P Manuale utente
Edimax
Edimax EK-PS2C Manuale utente
Edimax
Edimax ES-3305P V3 Manuale utente
Edimax
Edimax GS-3008P Manuale utente
Edimax
Edimax ES-5844P Manuale utente
Edimax
Edimax EK-2U2C Manuale utente
Edimax
Edimax ES-5500G V3 Guida di riferimento
Edimax
Edimax EK-PA2C Manuale utente
Edimax
Edimax ES-5816P Guida di riferimento
Edimax
Edimax ES-1008PL Manuale utente
Edimax
Edimax EU-HB4S Manuale utente
Edimax
Edimax 16 Port Nway Fast Ethernet PoE Web Smart... Manuale utente
Edimax
Edimax SP-2101W V3 Manuale utente
Edimax
Edimax ES-5160G V2 Manuale utente
