Ekwb EK-FB ASUS ROG ZE Monoblock Manuale utente

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on October 10th 2017

REMOVING STOCK COOLER. Remove all encircled screws. There are 4 (four) screws

on the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET heat pipe cooling solution. And 3 (three) screws for the

plastic factory I/O cover. Please store away the factory backplate and I/O cover as

it will be reused.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS ZENITH EXTREME motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PREPARING YOUR MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo below with enclosed thermal grease.

The quantity of about two stripes is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

STEP 4: CUTTING THERMAL PADS

Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s circuit board. WARNING:

DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]

Installation manual for EK-FB ASUS ROG ZE Monoblock water block

Mosfets

CPU socket

AMD X399

Chipset

1. Thermal pad G–1.0mm

(for mosfets and inductor coils):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on October 10th 2017

Place thermal pads on PCB as shown on the picture below.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL

PADS PRIOR TO INSTALLATION!

STEP 5: PLACING THERMAL PADS

STEP 6: PLACING A BLOCK ON TO THE MOTHERBOARD

Place the EK-FB ASUS ROG ZE Monoblock series water block gently to the motherboard

or vice versa (as shown on photo below). Make sure that mounting holes are aligned.

Place it on factory installed washers on the motherboard (MOSFET area).

STEP 7.1: ATTACHING A BLOCK ON TO THE MOTHERBOARD

STEP 7.2: ATTACHING A BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Secure top 4 (four)

nickel screws with enclosed 2,5mm Allen key. Tighten screws diagonally and evenly

till the end of the thread. Do not use excessive force when tightening the screws!

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Use 2 (two) M2,5x7 AX1

screws with original backplate. Tighten the screws evenly. Do not use excessive force

when tightening the screws! Now you can reinstall factory plastic I/O cover.

STEP 8: CONNECTING THE D-RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock D-RGB LED strip to the ADD HEADER on

the motherboard. Please ensure that the arrow indicated on the connector is plugged

into the +5V line as indicated on your motherboard. Failure to do so will damage

your motherboard or LED strip.

For the EK-FB ASUS ROG ZE Monoblock series water block to operate properly the

G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET

PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EK-

ACF series please use hose clamps or appropriate substitute to secure the tubing to

the barb. The use of biocide containing and corrosion inhibiting coolant is always

recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

M2.5x7 screws

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Place 1mm thermal pads in

large strip over marked area

and make sure all mosfet chips

and inductor coils are covered.

Questo manuale è adatto per i seguenti modelli

Altri manuali ekwb Hardware per computer

ekwb

ekwb Vector 2 FTW3 RTX 3080/90 ABP Manuale utente

ekwb

ekwb EK-FC1080 GTX Ti Strix Manuale utente

ekwb

ekwb EK-FC R9-290X Manuale

ekwb

ekwb EK-Classic Pump Reservoir 160 SPC PWM D-RGB Manuale

ekwb

ekwb EK-Vector RTX Aorus 2080Ti Manuale utente

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manuale utente

ekwb

ekwb EK-FB ASUS Z270E Strix Monoblock Series Manuale utente

ekwb

ekwb Ultra Monoblock EK-FB GA X99 Manuale utente

ekwb

ekwb EK-Pro CPU Water Block SP5 Manuale utente

ekwb

ekwb EK-FB ASUS R5-E10 Guida

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Manuale utente

ekwb

ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Manuale utente

ekwb

ekwb EK-FC Titan Z Manuale

ekwb

ekwb EK-KIT HT Series Manuale utente

ekwb

ekwb EK-FC980 GTX TF5 Manuale

ekwb

ekwb EK-FC750 GTX Series Manuale utente

ekwb

ekwb EK-FB GA AX370 Gaming RGB Monoblock Manuale utente

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Manuale utente

ekwb

ekwb EK-FC Titan Series Manuale

ekwb

ekwb EK-FB EVGA X58 CLASSIFIED Manuale utente

ekwb

ekwb EK-FC980 GTX Ti Strix Manuale

ekwb

ekwb EK-FC580 DCII Guida

ekwb

ekwb Velocity-AMD Manuale utente

ekwb

ekwb EK-XRES 140 Revo D5 Series Guida

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb EK-FB ASUS ROG ZE Monoblock Manuale utente

Manuali Hardware per computer popolari di altre marche