Elcometer 319 S Manuale utente

User Guide

Elcometer 319 Model S & T

Dewpoint Meter

www.elcometer.com

Gauge Overview

Box Contents

Using the Gauge

Getting Started

The Sensors

Setting Limits

Taking a Reading

Using External Temperature Probes

Statistics

Batching - Model T

Reviewing Batch Data - Model T

Menu Structure - Model S

Menu Structure - Model T

Downloading Data - Model T

Spares & Accessories

Warranty Statement

Technical Specification

Legal Notices & Regulatory Information

www.elcometer.com

For the avoidance of doubt, please refer to the original English language version.

Gauge Dimensions: 174 x 75 x 35mm (6.85 x 2.95 x 1.38")

Gauge Weight: 300g (10.5oz) - including batteries

transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any form or by any

means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written permission of

Elcometer Limited.

CONTENTS

en-1

1 GAUGE OVERVIEW

1 Surface Temperature Probe

2 Air Temperature & Humidity Probe

3 LED Indicators - Red (left), Green (right)

4 LCD Display

5 Softkeys

6 On/Off Key

7 Wrist Strap Connection

8 USB Data Output Socket (below cover)

9 Battery Compartment

10 Integrated Magnets

11 K-Type Probe Connector (below cover)

www.elcometer.com en-2

2 BOX CONTENTS



Elcometer 319 Dewpoint Meter



Protective Pouch with Belt Clip



2 x AA Batteries



Wrist Harness



ElcoMaster Software & USB Cable (Model T only)



Calibration Certificate



User Guide

3 USING THE GAUGE

www.elcometer.com

en-3

Measurement Units -°C, g/kg,°F, gr/lb

Power: USB

Bluetooth On

Menu Softkey

Stats Softkey

Batch Softkey (Model T)

Hold Current Reading; Start / Stop Logging (Model T)

Trend Indicators - Value increasing or decreasing

Climatic Parameters - Maximum of 5

Power: Batteries - including battery life indicator

Manual Logging

Batch Softkey - when in batching (Model T)

Batch Number / Batch Reading Number (Model T)

Alarm - reading outside set and enabled limits

Softkeys Locked (Model T)

Interval Logging - when in batching (Model T)

Thermometer Mode On

External Probe Temperature

4.1 FITTING THE BATTERIES

Each gauge is supplied with 2 x AA alkaline

batteries.

To insert or replace the batteries:

1 Remove the battery cover by rotating the

retaining screw anti-clockwise.

2 Insert 2 batteries taking care to ensure

correct polarity.

3 Refit the cover and rotate the retaining screw clockwise to

secure.

The battery condition is indicated by a symbol in the top right of the

displa e more segments displayed, the better the y ( ). Th

condition of the batteries.

When no segments are displayed, it is not advisable to use the

gauge for interval logging over long periods of time (Model T only;

see Section 4.6 - ‘Setting Manual or Interval Logging’ on page en-7).

If the batteries are replaced during interval logging, the gauge may

show ‘Please Wait’ whilst it re-calculates the batch statistics.

When the batteries are nearly depleted, the battery power supply

symbol will start flashing and the gauge emits short beeps every 10

seconds to indicate that the batteries should be changed.

The gauge can also be powered via USB using the USB cable

supplied (Model T) or available to purchase as an accessory

(Model S) - see Section 15 - ‘Spares & Accessories’ on page en-21.

Note: The USB cable can not be used to charge the batteries.

4.2 SELECTING YOUR LANGUAGE

1 Press and hold the ON/OFF button until the Elcometer logo is

displayed.

2 Press Menu/Setup/Languages and select your language using



the softkeys.



3 Follow the on screen menus.

www.elcometer.com en-4

4 GETTING STARTED

To access the language menu when in a foreign language:

1 Switch the gauge OFF.

2 Press and hold the left softkey and switch the gauge ON.



3 Select your language using the softkeys.



4.3 SCREEN SETTINGS

A number of screen settings can be defined by the user via

Menu/Setup/Setup Backlight including:

 Backlight Brightness; This can be set to ‘Low’, ‘Medium’ or

‘High’.

 Backlight Timeout; The display will dim if inactive for the

period defined by the user. To adjust the backlight timeout use



the softkeys to highlight ‘Backlight Timeout’ and press



‘Sel’. Use the softkeys to set the required value - between



0 (off) and 60 seconds - and press ‘Ok’ to set or ‘Esc’ to

cancel.

The gauge can also be set to switch off automatically after a user

defined period of inactivity - between 1 and 10 minutes - via

Menu/Setup/Auto Switch Off.

Note: ‘Auto Switch Off’ is disabled when the gauge is powered by the USB

connection.

4.4 SETTING UP THE READING DISPLAY

The user can select up to five climatic parameters to be displayed

on screen. Measurements are taken for all climatic parameters but

only those selected are displayed. Users can select from:

 RH; % Relative Humidity

 Ts; Surface Temperature

 Ta; Air Temperature

 Td; Dewpoint Temperature - calculated from Ta and RH

 TΔ; Delta Temperature - the difference between surface

temperature and dewpoint

 Tdb; Dry Bulb Temperature - equal to Ta

4 GETTING STARTED (continued)

www.elcometer.com

en-5

 Twb; Wet Bulb Temperature - calculated from Ta and RH

 SH; Specific Humidity - calculated from Ta and RH

Note: The formula used for calculation of Twb and SH uses a fixed value of air

pressure set at 1.0 atmosphere (1013mbar). The accuracy of Twb and

SH will vary at other values of atmospheric pressure. This variation may

be greater than ±1°C for Twb and ±1% / 10 mbar for SH.

To setup the display:

1 Press Menu/Setup/Display/Select

Readings.

2 Use the softkeys to highlight the



required option and press ‘Sel’.

Pressing ‘Sel’ again will de-select the

option.

 The gauge will beep if the user attempts to

select a parameter when five are already

selected in which case, a parameter must

be de-selected before another is chosen.

3 To select which parameter is shown in

the largest digits at the bottom of the

display, press

Menu/Setup/Display/Main Reading.

4 Use the softkeys to highlight the



required option from the list displayed

and press ‘Sel’.

 Only those climatic parameters selected via Step 2 above will be available

for selection in the ‘Main Reading’ list.

 To increase the size of the main reading, reduce the number of

parameters displayed on the reading screen.

Note: If a reading exceeds any set limits during measurement, it will be shown

flashing on the display, even if it has not been selected for display via

Steps 1-2 above.

4.5 SELECTING THE MEASUREMENT UNITS

A choice of measurement units is available ; °C, °F, g/kg, gr/lb. To

select the measurement units, press Menu/Setup/Units.

www.elcometer.com en-6

4 GETTING STARTED (continued)

a g/kg and gr/lb relate to ‘Specific Humidity’ measurements only.

The sensors for (a) humidity (RH) and air

temperature (Ta); and (b) surface

temperature (Ts) are located at the top of

the gauge.

Note: The surface temperature sensor is serialised

for calibration traceability purposes.

FOR ACCURATE READINGS

 Do not obstruct airflow through the holes in the casing around

the humidity and air temperature sensors.

 Keep fingers away from the holes - body heat can affect

readings.

 Allow the gauge some time, approximately 20 minutes, to

acclimatise once it is brought from a cold environment into a

warm place and vice versa.

www.elcometer.com

en-7

4.6 SETTING MANUAL OR INTERVAL LOGGING

Users can choose to manually log readings - ‘Manual Logging’

(Model S & T) or program the gauge to take readings at set time

intervals and save the readings into the batch memory automatically

- ‘Interval Logging’ (Model T only).

To select ‘Manual Logging’ in immediate mode (Model S & T):

1 Press Menu/Setup/Manual Logging.

2 To select immediate saving of a reading, use the softkeys



to highlight ‘Save only’ and press ‘Sel’.

3 To select holding of a reading followed by an option to save,

use the softkeys to highlight ‘Hold & Save’ and press ‘Sel’.



 The default setting is ‘Hold & Save’.

‘Manual Logging’ is also available when in batching (Model T).

‘Interval Logging’ is only available when in batching (Model T).

For information on creating a new batch with ‘Manual Logging’ or

‘Interval Logging’, see Section 10.1 ‘Creating a New Batch’ on

page en-15.

4 GETTING STARTED (continued)

5 THE SENSORS

www.elcometer.com en-8

TO AVOID DAMAGE

Do not use excessive force when measuring surface

temperature. Light contact between the probe and the surface is

sufficient. Using force does not increase the measuring speed

or improve the accuracy of the measurement, but it does

increase wear and/or damage to the sensor tip.

Do not drag the surface temperature probe over the surface to

avoid excessive wear.

The humidity sensor is fragile and should never be touched. Do

not use compressed air to clean the sensors or the gauge.

If the surface of the humidity sensor becomes saturated with

moisture, allow the moisture to evaporate fully in a dry

environment before using the gauge to take measurements.

Protect the gauge from paint dust and dirt as much as possible

as these can affect the long term accuracy of the humidity

sensor. Always keep the gauge in its protective pouch when not

in use.

Do not wash the sensors in water or with solvents.

5 THE SENSORS (continued)

6 SETTING LIMITS

A lower and/or upper limit can be set by the user for any or all the

climatic parameters.

Limits can be set for individual readings (when not in Batching) or

limits can be set for each batch (when in Batching).

To set limits for individual readings (Model S & T):

1 Press Menu/Set Limits.

2 Use the softkeys to highlight the required parameter and



press ‘Sel’.

3 Use the softkeys to highlight ‘High Limit on’ and press ‘Sel’



to enable the limit.

4 Use the softkeys to highlight ‘High Limit’ and press ‘Sel’.



www.elcometer.com

en-9

5 Use the softkeys to set the required value and press ‘Ok’



to set or ‘Esc’ to cancel.

6 If required, repeat Steps 3-5 to set and enable a low limit value.

7 Repeat Steps 2-6 for each climatic parameter as required.

To set limits for a batch (Model T):

Limits can be set when a new batch is created. Once a reading is

saved into the batch, limits cannot be amended and limits cannot be

added.

1 Press Batch/New Batch/Limits.

2 Use the softkeys to highlight the required parameter and



press ‘Sel’.

3 Use the softkeys to highlight ‘High Limit on’ and press ‘Sel’



to enable the limit.

4 Use the softkeys to highlight ‘High Limit’ and press ‘Sel’.



5 Use the softkeys to set the required value and press ‘Ok’



to set or ‘Esc’ to cancel.

6 If required, repeat Steps 3-5 to set and enable a low limit value.

7 Repeat Steps 2-6 for each climatic parameter as required.

 Batch limits can be viewed at any time via Batch/Review Batches.

When the value of a parameter falls outside set and enabled limits;

 the appropriate parameter icon flashes;

 If a reading exceeds any set limits during measurement, it will be shown

flashing on the display, even if it has not been selected for display via

Menu/Setup/Display/Select Readings.

 the alarm symbol is displayed next to the parameter;

 the red LED flashes; b

 an audible alarm sounds ;

 when in batching (Model T); a reading which exceeds a high

limit is marked and a reading which exceeds a low limit is

marked .

Note: When the value of the parameter returns within limits, the alarm status is

cleared automatically.

6 SETTING LIMITS (continued)

b The volume of the alarm is determined by the beep volume set via Menu/Setup/Beep Volume

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Elcometer Strumento di misura

Elcometer

Elcometer 331 H Manuale utente

Elcometer

Elcometer 456 Manuale utente

Elcometer

Elcometer 500 Manuale utente

Elcometer

Elcometer Novo-Gloss 402 Manuale utente

Elcometer

Elcometer 3000 Series Manuale utente

Elcometer

Elcometer 319/2 Manuale utente

Elcometer

Elcometer CG20 Manuale utente

Elcometer

Elcometer 311 Manuale utente

Elcometer

Elcometer 2290 Manuale utente

Elcometer

Elcometer 456 Manuale utente

Elcometer

Elcometer 6014 Manuale utente

Elcometer

Elcometer 2350 Manuale utente

Elcometer

Elcometer 407L Manuale utente

Elcometer

Elcometer MTG2 Manuale utente

Elcometer

Elcometer 224 Manuale utente

Elcometer

Elcometer Novo-Gloss 406 Manuale utente

Elcometer

Elcometer Zahn 2210 Manuale utente

Elcometer

Elcometer CG60DL Manuale utente

Elcometer

Elcometer Protovale 331 Manuale utente

Elcometer

Elcometer PTG6 Manuale utente

Elcometer

Elcometer 456 Manuale utente

Elcometer

Elcometer 204 Manuale utente

Elcometer

Elcometer 124 Manuale utente

Elcometer

Elcometer 139 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente