Elcometer Adhesion Verification Unit Manuale utente

User Guide

Elcometer AVU

Adhesion Verification Unit

www.elcometer.com

For the avoidance of doubt, please refer to the original English language version.

Dimensions: 165 x 155 x 105mm (6.5 x 6.1 x 4.1")

Weight: 3kg (6.6lbs)

transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any form or by any

means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written permission of

Elcometer Limited.

CONTENTS

www.elcometer.com

en-1

Section

Page

Overview

en-2

Box Contents

en-2

Getting Started

en-3

Performing the Test

en-3

Assessing the Results

en-5

After Test

en-6

Dolly Adaptors

en-6

Warranty Statement

en-6

Technical Specification

en-6

Legal Notices & Regulatory Information

en-7

Appendix A:

en-8

Recommended Test Pressures & Acceptable Ranges

1 OVERVIEW

www.elcometer.com en-2

a The Elcometer AVU is supplied with an Elcometer 506 / 510 20mm dolly adaptor fitted. Dolly adaptors for other

adhesion gauges from Elcometer and other manufacturers, are available as optional accessories -

see Section 7 “Dolly Adaptors” on page en-6 for details.

1 Dolly Adaptor

2 LCD Display

3 Softkeys

4 Battery Life Indicator

5 Adhesion Reading

6 ‘Max Hold’ Key

7 Units of Measurement (MPA or PSI)

8 On/Off Key

2 BOX CONTENTS



Elcometer Adhesion Verification Unit (AVU)



Elcometer 506 / 510 dolly Adaptor for 20 & 14.2mm Skirt



Carry Case



2 x AA Batteries



Test Certificate



User Guide

3 GETTING STARTED

3.1 SWITCHING ON / OFF

To switch the gauge on, press and hold the “On/Off” ( ) key.

The gauge has an integrated backlight which will timeout after 30

seconds of inactivity.

The unit will switch off automatically after 5 minutes of inactivity.

www.elcometer.com

en-3

3 GETTING STARTED (continued)

3.2 SETTING UP THE ELCOMETER AVU

The procedure outlined below must be followed each time the

Elcometer AVU is switched on, prior to testing adhesion gauges.

1 Fit the appropriate dolly adaptor -

screwing clockwise to tighten into

position (Figure 1). The reading on

the Elcometer AVU display should be

zero.

 Do not overtighten as this will apply

pressure and result in inaccurate readings.

2 Connect an adhesion gauge or

actuator to the dolly adaptor

(Figure 2).

 Elcometer 506 / 510 actuator shown.

3 Apply pressure until the reading on the

Elcometer AVU display is between

2 - 3.4 MPa (300 - 500 psi).

4 Leave the gauge pressured for a

minimum of 30 minutes to prepare the

Elcometer AVU for test and allow the

equipment to settle.

Note: The Elcometer AVU should be set up in an

operating environment of between

20°C to 25°C (68°F to 77°F).

4 PERFORMING THE TEST

Figure 1

Figure 2

The Elcometer AVU is designed to provide users with a method of

verifying the performance of their pull-off adhesion gauges .

The performance of an adhesion gauge should be verified at a number

of test pressures. Refer to Appendix A on page en-8 for recommended

test pressures for Elcometer pull-off adhesion gauges based on our

certification procedures. For other manufacturers’ gauges, refer to the

manufacturers’ specification.

a The Elcometer AVU is supplied with an Elcometer 506 / 510 20mm dolly adaptor fitted. Dolly adaptors for other

adhesion gauges from Elcometer and other manufacturers, are available as optional accessories -

see Section 7 “Dolly Adaptors” on page en-6 for details.

www.elcometer.com en-4

4 PERFORMING THE TEST (continued)

1 Fit the appropriate dolly adaptor -

screwing clockwise to tighten into

position (Figure 1). The reading on the

Elcometer AVU display should be zero.

 Do not overtighten as this will apply

pressure and result in inaccurate readings.

2 Connect the adhesion gauge or

actuator to the dolly adaptor (Figure 2).

 Elcometer 506 / 510 actuator shown.

3 “MAX” should be displayed on the

Elcometer AVU LCD to indicate that

‘Max Hold’ is switched on. ‘Max Hold’

holds the Elcometer AVU reading

when the required test pressure has

been reached on the adhesion gauge.

Press the “MAX” softkey to switch

‘Max Hold’ on and off.

 The display will hold the maximum value

until the ‘MAX’ softkey is pressed again.

4 Apply pressure until the required test

pressure is reached on the adhesion

gauge and compare the adhesion

gauge’s reading with the reading on

the Elcometer AVU display - see

Section 5 “Assessing the Results” on

page en-5.

5 To switch between measurement

units, press the “MPa/psi” softkey.

The Elcometer AVU will provide adhesion readings for 20mm dollies

irrespective of which dolly adaptor is fitted - see below for additional

information.

ELCOMETER 506 / 510 DOLLY ADAPTOR FOR

50MM ACTUATOR SKIRT (Part Number: T99923936)

When using the Elcometer 506 Analogue Adhesion Tester with 50mm

dolly adaptor, the reading on the Elcometer AVU display should be

compared with the reading on the 20mm scale of the Elcometer 506

analogue pressure gauge.

Figure 1

Figure 2

a The Elcometer AVU is supplied with an Elcometer 506 / 510 20mm dolly adaptor fitted. Dolly adaptors for other

adhesion gauges from Elcometer and other manufacturers, are available as optional accessories -

see Section 7 “Dolly Adaptors” on page en-6 for details.

Adhesion gauges should be tested at a number of pressure / adhesion

values across their measurement range - see Appendix A page en-8

for recommended test pressures for Elcometer pull-off adhesion

gauges.

When comparing the adhesion gauge reading with the Elcometer AVU

reading, the user should refer to the adhesion gauge’s accuracy

statement. This is usually quoted in the operating instructions or

technical data sheet.

The adhesion gauge can be stated as performing within specification if

the Elcometer AVU adhesion reading is within the stated accuracy of

the adhesion gauge. If outside specification, re-calibration is

recommended - contact Elcometer or your local supplier for further

information.

The Elcometer AVU can be used to re-certify adhesion gauges if it has

a current and valid calibration certificate, dated within 12 months of

test. This provides users with a Calibration Certificate which is

traceable through the certification of the Elcometer AVU unit in

accordance with Elcometer’s procedures.

The Elcometer AVU is supplied with a Test Certificate as standard and

is also available with an optional Calibration Certificate. To certify or

re-certify the Elcometer AVU, contact Elcometer or your local supplier.

5 ASSESSING THE RESULTS

When using the Elcometer 506 Digital Adhesion Tester or Elcometer

510 Automatic Adhesion Tester with 50mm dolly adaptor, the dolly size

should be set to 20mm before test - refer to the Elcometer 506 or 510

User Guide for instructions on how to select the 20mm dolly size.

ELCOMETER 106 SCALE 6 DOLLY ADAPTOR

(Part Number: T99923938)

When testing the Elcometer 106 Pull-Off Adhesion Tester with the

Scale 6 dolly adaptor, the Elcometer AVU reading should be multiplied

by a conversion factor of 6.4516 before comparing with the adhesion

gauge reading.

For other manufacturers’ gauges, please refer to the manufacturers’

instructions for adhesion readings using 20mm dollies.

4 PERFORMING THE TEST (continued)

www.elcometer.com

en-5

6 AFTER TEST

1 Release all pressure from the adhesion gauge.

2 Detach the adhesion gauge or actuator from the dolly adaptor.

3 Press the “MAX” softkey to release the ‘Max Hold’.

7 DOLLY ADAPTORS

Dolly adaptors are available for testing Elcometer 106 , 506 and 510

pull-off adhesion gauges. Adaptors are also available for testing other

manufacturers’ gauges.

Description Part Number

Elcometer 506 / 510 Dolly Adaptor: T99923935

20 & 14.2mm Skirts

Elcometer 506 / 510 Dolly Adaptor: T99923936

50mm Skirt b

Elcometer 106 Dolly Adaptor: Scales 1 to 4 T99923937

Elcometer 106 Dolly Adaptor: Scale 6 T99923938

AT-M & AT-A Adhesion Gauge Dolly Adaptor T99923939

PAT Adhesion Gauge Dolly Adaptor T99923986

b The Elcometer AVU is not suitable for verifying the accuracy of the Elcometer 106 Scale 5 due to its scale

range.

8 WARRANTY STATEMENT

The Elcometer AVU is supplied with a 12 month warranty against

manufacturing defects, excluding contamination and wear.

www.elcometer.com en-6

9 TECHNICAL SPECIFICATION

Range

0 - 30MPa (0 - 4000psi)

Resolution

±0.01MPa (1psi)

Accuracy

±0.33% of full scale

Power

Supply

2 x AA alkaline dry batteries

(rechargeable batteries can be used)

Dimensions

165 x 155 x 105mm (6.5 x 6.1 x 4.1")

Weight

3kg (6.6lbs)

Note: Batteries must be disposed of carefully to avoid environmental contamination.

Please consult your local Environmental Authority for information on disposal in

your region. Do not dispose of any batteries in fire.

This product meets the Electromagnetic Compatibility Directive. The product is Class B, Group 1 ISM

equipment according to CISPR 11. Group 1 ISM product: A product in which there is intentionally

generated and/or used conductively coupled radio-frequency energy which is necessary for the internal

functioning of the equipment itself. Class B product are suitable for use in domestic establishments and

in establishments directly connected to a low voltage power supply network which supplies buildings

used for domestic purposes.

is a registered trademark of Elcometer Limited, Edge Lane, Manchester, M43 6BU.

United Kingdom

All other trademarks acknowledged.

The Elcometer AVU is packed in cardboard packaging. Please ensure that this packaging is disposed

of in an environmentally sensitive manner. Consult your local Environmental Authority for further

guidance.

10 LEGAL NOTICES & REGULATORY INFORMATION

www.elcometer.com

en-7

11 APPENDIX A

ELCOMETER 506 ANALOGUE GAUGES (Accuracy: ±1% of full scale)

Megapascals (MPa)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

3.0

2.74 - 3.26

18.0

17.74 - 18.26

8.0

7.74 - 8.26

23.0

22.74 - 23.26

13.0

12.74 - 13.26

ELCOMETER 506 ANALOGUE GAUGES (Accuracy: ±1% of full scale)

Pounds Per Square Inch (psi)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

500

462 - 538

2000

1962 - 2038

1000

962 - 1038

2500

2462 - 2538

1500

1462 - 1538

3000

2962 - 3038

ELCOMETER 506 DIGITAL GAUGES (Accuracy: ±1% of full scale)

Megapascals (MPa)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

2.0

1.74 - 2.26

15.0

14.74 - 15.26

5.0

4.74 - 5.26

20.0

19.74 - 20.26

10.0

9.74 - 10.26

25.0

24.74 - 25.26

ELCOMETER 506 DIGITAL GAUGES (Accuracy: ±1% of full scale)

Pounds Per Square Inch (psi)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

500

462 - 538

2000

1962 - 2038

1000

962 - 1038

2500

2462 - 2538

1500

1462 - 1538

3000

2962 - 3038

www.elcometer.com en-8

ELCOMETER 106 SCALE 1 (Accuracy: ±15% of the reading)

Pounds Per Square Inch (psi)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

100

85 - 115

400

340 - 460

200

170 - 230

500

425 - 575

300

255 - 345

ELCOMETER 106 SCALE 1 (Accuracy: ±15% of the reading)

Megapascals (MPa)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

0.5

0.43 - 0.58

2.5

2.13 - 2.88

1.0

0.85 - 1.15

3.0

2.55 - 3.45

1.5

1.28 - 1.73

3.5

2.98 - 4.03

2.0

1.70 - 2.30

ELCOMETER 510 AUTOMATIC GAUGES (Accuracy: ±1% of full scale)

Pounds Per Square Inch (psi)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

500

464 - 536

2000

1964 - 2036

1000

964 - 1036

2500

2464 - 2536

1500

1464 - 1536

3000

2964 - 3036

ELCOMETER 510 AUTOMATIC GAUGES (Accuracy: ±1% of full scale)

Megapascals (MPa)

Gauge

Pressure

Elcometer AVU

Acceptable Range

Gauge

Pressure

Elcometer AVU

Acceptable Range

2.0

1.75 - 2.25

15.0

14.75 - 15.25

5.0

4.75 - 5.25

20.0

19.75 - 20.25

10.0

9.75 - 10.25

25.0

24.75 - 25.25

11 APPENDIX A (continued)

www.elcometer.com

en-9

Indice

Lingue:

Altri manuali Elcometer Strumento di misura

Elcometer

Elcometer 103 Manuale utente

Elcometer

Elcometer CG100ABDL Manuale utente

Elcometer

Elcometer UG20DL Manuale utente

Elcometer

Elcometer 204 Manuale utente

Elcometer

Elcometer 112 Manuale utente

Elcometer

Elcometer 138 Manuale utente

Elcometer

Elcometer 331 H Manuale utente

Elcometer

Elcometer 224 Manuale utente

Elcometer

Elcometer PG70 Manuale utente

Elcometer

Elcometer 319 Standard Manuale utente

Elcometer

Elcometer 355 Manuale utente

Elcometer

Elcometer 148 Manuale utente

Elcometer

Elcometer 456 Manuale utente

Elcometer

Elcometer 3000 Series Manuale utente

Elcometer

Elcometer 701 Manuale utente

Elcometer

Elcometer 124 Manuale utente

Elcometer

Elcometer G116A-1 Manuale utente

Elcometer

Elcometer 2300 Series Manuale utente

Elcometer

Elcometer 345 Manuale utente

Elcometer

Elcometer CG20 Manuale utente

Elcometer

Elcometer 112 Manuale utente

Elcometer

Elcometer 456 Manuale utente

Elcometer

Elcometer Protovale 331 Manuale utente

Elcometer

Elcometer 207 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente