Elero QuinTec-868 Manuale utente

138210501_EN_0919

QuinTec-868

Operating instructions

(translation)

Product contents

• Wall transmitter module

• CR 2032 battery (installed)

• elero frame

• Black xing plate with xing set (wall plugs

and screws)

• Operating instructions

Technical data

Power

supply

3 V

battery, CR 2032

Radio frequency [MHz]

(band)

868

Transmission power

[mW] | [dBm]

≤ 500 | ≤ 10

Number of channels 5 + 1

Connections, terminals None

Operating temperature

[°C]

0 ... 50

Protection class (IP) 20

Dimensions (WxHxD)

[mm]

Wall transmitter module

Fixing plate

elero frame

50 x 50 x 9.6

approx. 75 x 75

approx. 80 x 80

Weight [g] approx. 50

Type of mounting Wall mounting

Item number 286550001

Safety instructions

Please read this operating manual carefully

as the procedure in this manual is a prere-

quisite for correct use of the product.

Only operate the transmitter within sight

of the devices being controlled.

It is not recommended to operate all drives

simultaneously. For safety reasons, at least

one drive should be controlled independently

from others to provide a safe escape route

in the event of an emergency.

The gures in this operating manual are for

illustration purposes only. The illustrations

may di󰀨er from your product with respect to

minor details and are provided for general

information only.

elero GmbH continuously strives to improve

all products. As a result, the specications,

features and technology of this product may

be changed at any time. The information in

this operating manual is based on current

information at the time of publication.

No claims can be derived from the technical

data, images and information in this opera-

ting manual.

&$87,21

Intended use

Foreseeable misuse

Only use in dry rooms for controlling elero

radio receivers. Do not perform any modi-

cations to the device. Do not operate the

transmitter inadvertently or carelessly. The

manufacturer will not assume liability for

damage caused by the above.

General

• 5-channel wall transmitter with 5 individual

channels and 1 central channel for operating

roller shutters, venetian blinds and awnings

• Suitable for standard device deployment

50 x 50 mm

• Radio frequency for reliable transmission

• Large operator buttons

• Display of system statuses using LEDs

Assembly / commissioning

Important: The battery is not activated at

delivery. For commissioning, remove the

insulating strip Ⓐ .

Make sure the radio link is unobstructed.

Avoid installing the unit in a distributor box

or metal housing, in direct proximity to large

metal objects, or on or close to the oor.

Check the installation surface for hidden

cables, etc.

Installation:

1. Attach the xing plate to the installation

location using the screws and wall plugs.

2. For programming the wall transmitter to

the radio control or receiver:

see “Programming the transmitter / channel”.

3. Insert the wall transmitter and the elero

frame into the xing plate at a right angle

with the wall.

Asynchronous

programming mode

Programming the transmitter / channel for

multiple receivers

Requirement: The receiver is installed

Programming can only be performed in one selec-

ted channel. Several receivers can be program-

med to one channel.

1. Switch the circuit o󰀨 and on again: The receiver

will remain ready to program / in programming

mode for approx. 5 minutes.

2. Position yourself with the transmitter to be pro-

grammed within sight and radio range of the blind.

3. Press the [P] programming button for approx.

1 second.

The blind will move up and down for approxima-

tely 2 minutes (programming mode).

If several receivers are connected to the same

feed line, then all are simultaneously ready to

program / in programming mode. The blinds will

start moving up and down randomly. The longer

programming is delayed, the greater the o󰀨set

will be. Individual receivers can now be assigned

to the respective channel of the transmitter.

4. Immediately (maximum 1 second) after the

start of upward travel, press the [UP ▲] button.

The blind will stop for a short time.

5. Immediately (maximum 1 second) after the

start of downward travel, press the

[DOWN/CLOSE ▼] button. The blind will stop.

Important: You can stop receivers that you

do not want to program by pressing the STOP

button ■ on an already programmed transmit-

ter. You can now make the channel assignment/

change without having to disconnect the indivi-

dual receivers.

6. If the blind moves in the opposite direction or the

blind does not stop after programming, delete

the transmitter from the receiver and repeat the

programming process.

7. QuinTec-868 is now programmed.

Stopping programming mode in the transmitter

Press the [STOP ■] button for at least 6 seconds

until the LED status ashes orange.

Programming additional transmitters /

channels to one receiver

1. Press the [UP ▲]+[DOWN/CLOSE ▼]+[P]

buttons simultaneously for 3 seconds on a trans-

mitter that has already been programmed to the

receiver. The LED status and operating mode ④

goes out after about 3 seconds. The receiver will

remain in programming mode for approximately

5 minutes. Press the programming button [P] on

the transmitter to be programmed for approxi-

mately 1 second.

2. Immediately (maximum 1 second) after the start

of upward travel, press the [UP ▲] button.

The LED status and operating mode ④ lights

up briey. The blind stops, starts moving again,

stops again, and then moves downwards.

3. Immediately (maximum 1 second) after the

start of downward travel, press the

[DOWN/CLOSE ▼] button.

The indicator light will light up briey.

The blind will stop.

4. The transmitter or the transmitter channel has

been programmed.

Deleting individual transmitters / channels

1. Press the [STOP ■]+[P] buttons simultaneously

and hold them down for approx. 6 seconds.

2. The indicator light will light up orange and

then red.

Delete all transmitters and receivers

To perform a factory reset, all selected drives must

be supplied with power.

1. Press the [UP ▲]+[DOWN/CLOSE ▼]+

[STOP ■]+[P] buttons and hold them down for at

least 6 seconds.

2. LED status ④ shines orange rst and then red.

Follow these instructions to ensure proper

and safe use. Retain for future use.

Control elements, front

① Fixing plate

② eleroframe

③Wall transmitter module

④ LED status and operating mode

⑤ LEDs channels 1 to 5

⑥ UP ▲ button

⑦ STOP ■ button

⑧ DOWN/CLOSE ▼ button

⑨ Selection button for channel and operating

mode

Back / battery replacement

123456

12345678

286550001RM

286550001RM.asm

24.10.17 HERMANNC

Rohteil QuinTec-868

für Adapterrahmen 50x50 mm

1:5

Diese Maße werden besonders geprüft

This dimensions are particularly examined

Gratfrei

burr-free

Allgemeintoleranzen

General Tolerances:

DIN ISO 2768-1 m-E

DIN ISO 2768-2 K-E

Maßstab / Scale:

Werkstoff / Material:

Datum / Date: Name:

A-EW

geprüft

proofed:

Benennung / Title:

Zeichnungsnummer / Drawingnumber:

Werkzeug-Nr

Tool-Number:

Gemäß RoHS-Richtlinie 2011/65 EG / according to RoHS directive 200/11/EU

Index: Kurzbeschreibung / Short Comment: Name:Datum / Date:

elero GmbH

Antriebstechnik

Maybachstr. 30, D-73278 Schlierbach

Fon: (0049) 7021 / 9539-0

Fax: (0049) 7021 / 9539-212

Verwendung , Kennzeichnung / Used in, Spezification:

Gewicht / weight:

Solid Edge

CAD-Nr / CAD-No:

DIN A4

Format / format:

rev. Nr.

Lieferantenkennzeichnung nach Absprache

Supplier ID according to prior agreement

0,000 kg

Reg. Nr

Fehler: Keine Referenz

Fehler: Keine Referenz - -

Ⓐ Insulating strip

Ⓑ Battery compartment with marking

Disposal

Batteries and old units may not be disposed

of with household waste!

1. Dispose of packaging in the recycling bin

for cardboard and paper.

2. Dispose of old batteries in the recycling

bin for used batteries or have a retailer

recycle them.

3. Dispose of old units at an electronic waste

recycling facility or have a retailer recycle

them.

Conformity

elero hereby declares that QuinTec-868 wall

transmitter is in compliance with Directive

2014/53/EU. The full text of the EU Declaration

of Conformity is available at the following

internet address:

www.elero.com/downloads-service/

Service/manufacturer's

address

If malfunctions have occurred or the device

has been damaged despite proper handling,

contact your contractor or dealer.

elero GmbH

73278 Schlierbach

GERMANY

www.elero.de

Repairs

Please specify the item number, item

description, type of fault, situational circum-

stances, presumed cause, unusual events

prior to the problem.

Cleaning

Clean the device with a damp cloth only.

Do not use cleaning agents because they

can damage the surfaces.

Warranty

Within the legal warranty period, we will

remedy any defects caused by material or

manufacturing defects by repairing or

replacing the unit. Unauthorised modica-

tions will void the warranty.

LED status and

operating mode ④

Green - steady If the Selection button

pressed previously:

Operating mode Auto

Red - steady If the Selection button

pressed previously:

Operating mode Manual

Orange - as-

hing slow

Channel (transmitter)

not programmed in any

receiver

Orange - as-

hing fast

(approx. every

2 seconds)

Channel (transmitter) is

in programming mode.

Operation of receivers

already programmed is

not possible.

Orange - ashing

fast (approx.

every 2 seconds)

More than 10 receivers are

ready for programming.

Orange or green -

ashing multiple

times, then red

after 6 seconds

Channel (transmitter)

has been deleted

Red - ashing

quickly

Battery almost depleted

Synchronous

programming mode

For programming one transmitter to multiple

receivers at the same time.

1. Press the [DOWN/CLOSE ▼]+ [P] but-

tons simultaneously for 3 seconds on a

transmitter that has already been pro-

grammed to the receiver. The status LED

ashes orange and green multiple times.

The receivers are now synchronously in

programming mode. The blind moves in

briey in the down direction.

2. With the transmitter to be programmed,

perform steps 1 to 7 as described under

“Programming the transmitter / channel”.

Conguring the drive

Dening the intermediate position

Requirement:

The blind is in the upper end position.

1. Press the [DOWN/CLOSE ▼] button until

the desired intermediate position is reached.

2. Additionally, briey press the [STOP ■] button.

The blind will stop. The intermediate positi-

on has now been stored.

Dene one of the ventilation/tilting/fabric

tautening positions

Requirement:

The blind is in the lower end position.

1. Press the [UP ▲] button until the ventilati-

on gaps open, the venetian blind slats are

tilted or the awning fabric is taut.

2. Additionally, briey press the [STOP ■] button.

The blind will stop. The ventilation / tilting /

fabric tautening position has been stored.

Moving to the intermediate position

Requirement:

The intermediate position is dened and the

blind is in the upper end position (combined

with Combio).

1. Press the [DOWN/CLOSE ▼] button twice

(in quick succession): The blind moves to

the saved intermediate position.

If no intermediate position has been dened,

the blind moves to the lower end position.

Important: If you are using venetian blinds

and a dened tilt position, the venetian blind

slats will also tilt.

If no tilt position has been dened, the blind

will stop at the intermediate position with the

slats closed.

Moving to the ventilation / tilting / fabric

tautening positions

Requirement:

The position of the ventilation / tilting / fabric

tautening is dened and the blind is in the

lower end position (combined with Combio).

1. Press the [OPEN ▲] button twice in quick

succession:

The blind moves to the saved position.

If no ventilation / tilting / fabric tautening

position is dened, the blind moves to the

upper end position.

Deleting the intermediate position

Requirement: The transmitter is programmed.

1. Press the [DOWN/CLOSE ▼]+ [STOP ■]

buttons simultaneously for approx. 3 seconds.

The intermediate position is now deleted.

The indicator light will light up briey.

Deleting the ventilation position / tilting

position / fabric tautening position

Requirement: The transmitter is programmed.

1. Press the [UP ▲]+ [STOP ■] button simul-

taneously for approx. 3 seconds.

The ventilation / tilting / fabric tautening posi-

tion has now been deleted. The LED status

and operating mode ④ lights up briey.

Selection button ⑨

Auto Manual

A receiver that is

programmed res-

ponds to the timer

function of a corres-

ponding control unit

or to commands by

sensors.

A receiver that is

programmed does

not respond to the

timer function of a

corresponding con-

trol unit or to com-

mands by sensors.

• Short operation: Display of the current

operating mode Auto / Manual with

selection Next channel / Central channel.

• Operation approx. 1 s duration: Display of

the current operating mode Auto / Manual

without channel change.

• Long press approx. 2 s duration:

Switch between operating modes Auto

and Manual.

Important:

Wind sensors trigger corresponding travel

movements in both operating modes.

Notes on troubleshooting

Fault Cause Remedy

Drive not

running,

indicator

light not

illuminating

Battery

depleted

The battery

is incorrectly

installed

Install a new

battery

Insert the

battery

correctly

The drive is

not running,

the status

LED shines

or ashes

red

1. The

receiver

is outside

radio

range

2. Receiver

not ope-

rating or

faulty

1. Reduce

distance

to the

receiver

2. Switch on

or replace

receiver

Drive runs

in the wrong

direction

Directions

are incorrec-

tly program-

med

Delete

transmitter

and program

correctly

LEDs channels 1 to 5 ⑤

shining green

Display active channel(s)

(1 or 5 channels) (one

channel / the central chan-

nel is always selected)

Replacing the battery

After a battery change, the transmitter pro-

gramming is retained; QuinTec does to have

to be reprogrammed into the radio receiver/

transmitter.

1. Pry the wall transmitter module ③ and the

elero frame ② out of the xing plate ①.

2. Carefully pull the battery out of the battery

compartment Ⓑ using a blunt, insulated

tool. Use only a CR 2032 battery. Make

sure the polarity is correct. The positive

terminal must be visible.

3. Reinsert the wall transmitter ③ into the

xing plate ①.

Dispose of the used battery in accordance with

environmental regulations.

Central channel

• Same control system for several receivers

with one travel command.

• All programmed receivers can be controlled

in the central channel.

• QuinTec-868 can be programmed in several

receivers.

Indice

Altri manuali elero Sistema di controllo

elero

elero Picolo 0 Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente

elero QuinTec-868 Manuale utente

Manuali Sistema di controllo popolari di altre marche