Elsner KNX W Guida

KNX W

Wind Sensor

Installation and Adjustment

Item number 70123

1 Content

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Wind Sensor KNX W • from software version 1.00, ETS programme version 1.1

Status: 18.04.2023 • Errors excepted. Subject to technical changes.

1. Description ........................................................................................... 3

1.1. Deliverables .............................................................................................................. 3

1.2. Technical specifications ........................................................................................... 3

2. Installation and commissioning ........................................................... 4

2.1. Location ..................................................................................................................... 4

2.2. Mounting the sensor ................................................................................................ 5

2.2.1. Attaching the mount ..................................................................................... 5

2.2.2. View of rear side and drill hole plan ........................................................... 7

2.2.3. Preparing the sensor .................................................................................... 8

2.2.4. PCB layout ..................................................................................................... 9

2.2.5. Mounting the weather station ..................................................................... 9

2.3. Notes on mounting and commissioning .............................................................. 10

3. Addressing of the device at the bus .................................................. 10

4. Maintenance ....................................................................................... 11

5. Disposal ............................................................................................. 11

6. Transmission protocol ....................................................................... 12

6.1. List of all communication objects ......................................................................... 12

7. Setting of parameters ........................................................................ 15

7.1. General settings ..................................................................................................... 15

7.2. Threshold values .................................................................................................... 15

7.2.1. Wind threshold value 1 / 2 / 3 .................................................................... 15

7.3. Logic ....................................................................................................................... 17

7.4. AND Logic 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 ......................................................................... 17

7.4.1. Linkage inputs of AND Logic ..................................................................... 18

7.4.2. OR Logic 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 ................................................................ 19

7.4.3. Linkage inputs of OR Logic ........................................................................ 19

2 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

ETS In the ETS tables, the parameter default settings are marked by

underlining.

3 Description

Wind Sensor KNX W • Status: 18.04.2023 • Technical changes reserved. Errors reserved.

1. Description

The Wind Sensor KNX W measures wind speed and transfers the values to the KNX

system. Three switching outputs with adjustable threshold values as well as additional

AND and OR logic gates are available.The sensor system, the evaluation electronics

and the electronics of the bus connection are mounted in a compact housing.

Functions:

•Wind measurement: The wind strength measurement takes place

electronically and thus noiselessly and reliably, even during hail, snow and

sub-zero temperatures. Even turbulent air and anabatic winds in the vicinity of

the weather station are recorded

•Wind sensor monitoring: If the wind measurement value changes by less

than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is

output as a fault message. All wind alarms with a limit value below 35 m/s

become active as a result

•3 threshold values can be adjusted per parameter or via communication

objects

•8 AND and 8 OR logic gates with each 4 inputs. Every switching incident as

well as 8 logic inputs (in the form of communication objects) may be used as

inputs for the logic gates. The output of each gate may optionally be configured

as 1 bit or 2 x 8 bits

Configuration is made using the KNX software ETS. The product file can be down-

loaded from the Elsner Elektronik website on www.elsner-elektronik.de in the “Ser-

vice” menu.

1.1. Deliverables

• Sensor with combined wall/pole mounting

• 2x stainless steel installation band for pole installation

1.2. Technical specifications

Housing Plastic material

Colour White / translucent

Mounting On-wall

Degree of protection IP 44

Dimensions approx. 96 × 77 × 118 (W × H × D, mm)

Weight approx. 170 g

Ambient temperature Operation -30…+50°C, storage -30…+70°C

Operating voltage 20...30 V DC.

An appropriate power supply unit can be obtained from

Elsner Elektronik.

Cable cross-section Massive conductors of up to 1.5 mm² or conductors

with fine wires

4 Installation and commissioning

Wind Sensor KNX W • Status: 18.04.2023 • Technical changes reserved. Errors reserved.

The product conforms with the provisions of EU directives

2. Installation and commissioning

Installation, testing, operational start-up and troubleshooting should

only be performed by an authorised electrician.

CAUTION!

Live voltage!

There are unprotected live components inside the device.

• Inspect the device for damage before installation. Only put undamaged devic-

es into operation.

• Comply with the locally applicable directives, regulations and provisions for

electrical installation.

• Immediately take the device or system out of service and secure it against un-

intentional switch-on if risk-free operation is no longer guaranteed.

Use the device exclusively for building automation and observe the operating instruc-

tions. Improper use, modifications to the device or failure to observe the operating in-

structions will invalidate any warranty or guarantee claims.

Operate the device only as a fixed-site installation, i.e. only in assembled condition and

after conclusion of all installation and operational start-up tasks, and only in the sur-

roundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

2.1. Location

Select an assembly location at the building where wind speed may be collected by the

sensor unobstructedly.

At least 60 cm of clearance must be left all round the device.This facilitates correct wind

speed measurement without eddies. The distance concurrently prevents spray (rain-

drops hitting the device) or snow (snow penetration) from impairing the measurement.

It also does not allow birds to bite it.

Current max. 30 mA., max. 0,4 W.

Residual ripple 10%

Data output KNX +/- bus terminal plug

Group addresses max. 254

Allocations max. 255

Communication objects 80

Measurement range Wind 0...35 m/s

5 Installation and commissioning

Wind Sensor KNX W • Status: 18.04.2023 • Technical changes reserved. Errors reserved.

2.2. Mounting the sensor

2.2.1. Attaching the mount

The sensor comes with a combination wall/pole mount. The mount comes adhered by

adhesive strips to the rear side of the housing. Fasten the mount vertically onto the wall

or pole.

Fig. 1

There must be at least 60 cm of space below,

to the sides and in front of the sensor left

from other elements (structures, construction

parts, etc.).

60 cm

Fig. 2

The wind sensor must be mounted on a verti-

cal wall (or a pole).

Wall

pole

Fig. 3

The wind sensor must be mounted in the

horizontal transverse direction (horizontally).

Horizontal

6 Installation and commissioning

Wind Sensor KNX W • Status: 18.04.2023 • Technical changes reserved. Errors reserved.

Fig. 4

When wall mounting: flat side on wall, crescent-

shaped collar upward.

Collar

Fig. 5

When pole mounting: curved side on pole, collar

downward.

Collar

Fig. 6

Different mounting arms are available from Els-

ner Elektronik as additional, optional accessories

for flexible installation of the weather station on

a wall, pole or beam.

Example of the use of a mounting arm:

Due to flexible ball joints, the sensor can be

brought into ideal position.

Fig. 7

Example use of the hinge arm mounting:

Fitting to a pole with worm drive hose clips

7 Installation and commissioning

Wind Sensor KNX W • Status: 18.04.2023 • Technical changes reserved. Errors reserved.

2.2.2. View of rear side and drill hole plan

Slot hole 7,5 x 5 mm

Fig. 8 a+b

Drill hole plan

Dimensions of rear side of

housing with bracket. Sub-

ject to change for technical

enhancement.

8 Installation and commissioning

Wind Sensor KNX W • Status: 18.04.2023 • Technical changes reserved. Errors reserved.

2.2.3. Preparing the sensor

The sensor cover snaps in on the left and right along the bottom edge (see Fig.). Re-

move the cover. Proceed carefully, so as not to pull off the wire connecting the PCB in

the bottom part with the cover (cable with plug).

Lead the cable for the voltage supply and bus connection through the rubber seals on

the bottom of the device and connect Voltage L/N and Bus +/- to the terminals provid-

ed.

The connection cable must be plugged in between the cover and the circuit board.

Fig. 9

1 Cover Snaps

2 Bottom part of housing

Unsnap cover and

remove upwards

Fig. 10

Remove the cable shielding under the circuit

board and only feed the connector cables up-

wards through the openings in the circuit

board.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Elsner Strumento di misura

Elsner

Elsner Cala KNX IL CH Guida

Elsner

Elsner KNX TH65-AP Guida

Elsner

Elsner KNX TH65-AP Manuale utente

Elsner

Elsner KNX PY Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente