Embedded Wireless Zilant ZMX-8100 Manuale utente
ZILANT™
USER MANUAL
THIS PAGE HAS BEEN LEFT BLANK
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 3 -
Zilant™User Manual
ZMX-8100
ZUM-VG-371220113
www.embeddedwireless.com
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 4 -
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved
All information provided here are subject to change without prior notice.
Trademarks
Zilant™ and ZMS User Interface are trademarks of Embedded Wireless. Names of other
products, companies or standards mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
Revision History
Part No
Revision History Date
ZPM-VG-366260911 Initial release of Zilant™ Product Manual 08/11
ZPM-VG-370190712 New Feature and user interface 07/12
ZUM-VG-371220113
ZUM-VG-372220113
Issued End User version. Updates to LED indicators and EW
profile.
Antenna, LED Indicator, Safety measures
01/13
01/13
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 5 -
Contents
Copyright Notice & Revision History
Contents Page
Welcome Note
Regulatory Statements
1.0 Introduction
About Embedded Wireless
Product Support
2.0 Inspect Product Checklist
3.0 Hardware Configuration
Front Panel Interface
Back Panel Interface
4.0 Installing the Unit
Connect Antenna, Interfaces Port and Power Supply
5.0 Device Readiness
6.0 Restore Factory Default Settings
7.0 Limited Warranty
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 6 -
WELCOME NOTE
Thank you for choosing the Zilant™ product.
The user manual describes how to install and configure the Zilant™ unit.
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 7 -
Wireless Safety and Compliance
Turn wireless off in areas where wireless use is forbidden or when it may cause
interference or danger. Some specific situations are described below. In general,
you should not use your Device with wireless turned on any place you are not
allowed to use a cellular device.
Be Careful Around Other Electronic the Devices The Device generates, uses,
and can radiate radio frequency (RF) energy and, if not used in accordance with
its instructions, may cause harmful interference to radio communications and
electronic equipment. External RF signals may affect improperly installed or
inadequately shielded electronic operating systems, entertainment systems and
personal medical devices. While most modern electronic equipment is shielded
from external RF signals, if in doubt, check with the manufacturer. For personal
medical devices (such as pacemakers and hearing aids), consult with your
physician or the manufacturer to determine if they are adequately shielded from
external RF signals.
Steps to Minimize Interference
If your Device does cause harmful interference to radio or television reception
(which you can determine by turning your Device off and on), you can try to
correct the interference by one or more of the following measures: reorient or
relocate the receiving antenna for the radio or television; increase the separation
between the radio or television and your Device; connect equipment and
receivers to different outlets; or consult the radio or television manufacturer or an
experienced radio/TV technician for help.
Where to Place the Device
The Device should be placed close to your wall power outlet and is normally
more than 20cm from your body. . For example, the Device can be placed on the
floor under a table.
Information regarding Exposure to Radio Frequency Energy Exposure to
Radio Frequency Energy
Your Device is designed and manufactured not to exceed the emission limits for
exposure to RF energy set by the Federal Communications Commission of the
United States (FCC). It should be installed and operated with a minimum
distance of 20 cm from your body. It must not be co-located or operating in
conjunction with any other antenna or transmitter. Information on your Device is
on file with the FCC and can be found under the Display Grant section of
http://www.fcc.gov/oet/ea/ after searching on the FCC ID for your Device, which
can be found on the back of the Device.
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 8 -
Regulatory Statements
The product must be set up and operated strictly according to manufacturer’s
instructions included in the user documentation provided with the product. All
changes and modifications must be expressly approved by the manufacturer.
Failure to do so may nullify the user’s authority to operate the product. The
manufacturer and its authorised resellers and distributors will assume no
responsibility for damage from any failure to comply with these guidelines.
FCC Compliance Statement for Model Number ZMX8100, FCC ID:
R42ZMX8100
This Device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This Device may not cause harmful interference; and
(2) this Device must accept any interference received, including interference that
may cause undesired operation.
This Device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. However, there is no guarantee that interference will not occur in a
particular installation.
This Device meets the FCC Radio Frequency Emission Guidelines and is
certified with the FCC as the FCC ID number found on the back of the Device.
Important: Changes or modifications to the Device not expressly
authorized by Company could void your authority to operate the Device.
This product is listed by UL. Representative samples of this product have
been evaluated by UL and meet applicable safety standards.
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 9 -
1.0 Introduction
EMBEDDED WIRELESS
Embedded Wireless builds next generation wireless products. The company is
strongly committed to building successful products and have patented over 47
technologies.
Why choose products by Embedded Wireless
Embedded Wireless is a next-generation wireless telecommunications company
offering connected healthcare and services for independent living, chronic
disease management, elderly home care, personal wellness, intelligent
automation, end-end 3G/4G enterprise solutions and telecommunications.
Embedded Wireless delivers custom-designed products and solutions with
cutting-edge engineering capabilities in digital hardware, RF, ASIC/ FPGA,
software and embedded software.
Visit the Website
Browse the Embedded Wireless website at www.embeddedwireless.com.
The Website provides product information, data sheets and access to customer
support.
Product Manual for Zilant™
Copyright © 2013 Embedded Wireless Labs Sdn Bhd. All rights reserved. - 10 -
PRODUCT SUPPORT
Contact your product reseller for product support.
Please provide the following information when contacting support services by
email-
Model number or product name
Serial number of the product
Firmware revision
Any possible screenshots or visual feedback relating to the problem.
Check label at the bottom of the unit for more information.
Indice
