Emerson Keystone EPI2 Manuale utente
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
May 2022
Keystone OM11 - EPI2
DeviceNet Interface
Notes
May 2022
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
This page is intentionally left blank
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
Table of Contents
May 2022
Table of Contents i
Table of Contents
Section 1: Introduction
Introduction ........................................................................................................... 1
Section 2: Operation and Storage
Operation and Storage............................................................................................ 2
Section 3: Distinguish Old/New Models
Distinguish Old/New Models................................................................................... 3
Section 4: Installation
4.1 Assembling Procedure for Models 63-125 Nm
Old Version (US or Non-US Market) ............................................................... 6
4.2 Assembling Procedure for Models 250-500-1000-2000 Nm
Old Version (US or Non-US Market) ............................................................... 9
Section 5: Communication Features
Communication Features ..................................................................................... 11
Section 6: DeviceNet Interface Module
6.1 On Board Indication Module........................................................................ 12
6.2 Wiring Diagram........................................................................................... 14
6.3 Bus/Hardwired Mode Selection ................................................................... 14
Section 7: Brief DeviceNet Description
7.1 Network Cable ............................................................................................ 16
7.2 Terminator ................................................................................................. 16
Section 8: Communication Interface
8.1 Actuator Commands................................................................................... 17
8. 2 Actuator Status and Indication ................................................................... 18
8.2.1 Positioning Algorithm ...................................................................... 19
8.3 Fail-Safe Data .............................................................................................. 20
8.4 DeadBandConguration ........................................................................... 20
8.5 UserDenedData ...................................................................................... 21
8.6 CongurationData..................................................................................... 21
8.7 DeviceNetCongurableParameters........................................................... 23
8.8 EDS File ....................................................................................................... 23
Table of Contents
May 2022
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
Table of Contentsii
Section 9: Local Settings
9.1 On-Board Interface...................................................................................... 25
9.2 DeviceNetMACIDConguration ................................................................. 26
9.3 DeviceNetCommunicationSpeedConguration ........................................ 27
Section 10: Bluetooth Communication Module
Bluetooth Communication Module....................................................................... 28
Section 11: DeviceNet Certicate
DeviceNetCerticate............................................................................................ 29
Section 12: Optional Kits
Optional Kits ......................................................................................................... 30
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0 May 2022
1
Section 1: Introduction
Introduction
NOTE:
Before installation, these instructions must be fully read and understood.
Section 1: Introduction
The OM11 DeviceNet interface is an electronic module that allows you to connect the
Keystone EPI2 electrical actuator to a DeviceNet network. The module has its own
microprocessor and acts as a pure bus interface without affecting the actuator control
integrity. It is installed inside the actuator housing and takes the electrical power from the
actuator power supply module. The DeviceNet network is fully isolated from the
actuator electronics.
For details about EPI2 actuator, please refer to Installation, Operation and Maintenance
Manual for Keystone EPI2, Electric Actuator.
!WARNING
EPI2 actuators must be electrically isolated before any disassembling or reassembling
operations. Before any disassembling or reassembling operations, please follow in detail
the relevant section of the basic installation and operating manual (latest revision available).
!WARNING
The electronic parts of the EPI2 actuators and all option modules can be damaged by
a discharge of static electricity. Before you start, touch a grounded metal surface to
discharge any static electricity.
! WARNING
Itisassumedthattheinstallation,conguration,commissioning,maintenanceandrepair
worksarecarriedoutbyqualiedpersonnelandcheckedbyresponsiblespecialists.
! WARNING
Repairwork,otherthanoperationsoutlinedinthismanual,isstrictlyreservedtoqualied
Emerson personnel or to personnel authorized by the company itself.
May 2022
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
2
Section 2: Operation and Storage
Operation and Storage
Section 2: Operation and Storage
The module is designed to work and to be stored in the same environment as the actuator.
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0 May 2022
3
Section 3: Distinguish Old/New Models
Distinguish Old/New Models
Figure 1 Label for non-US market - digits X7X8 on product coding chart
Section 3: Distinguish Old/New Models
It is important to distinguish between EPI2 old models and the new ones. To install the
board on base actuator, in fact, it is necessary to choose the correct mechanical parts from
the kit.
Furthermore, the meaning of some data exchanged on the DeviceNet interface depends
on model (old or new); differences will be explained in the following sections.
Figures 1 and 2 allow to distinguish old version of EPI2 from the new version (on the labels,
the digits of Product Number are boxed); furthermore, the logic boards with heatsink
identiesoldversionmodels,whilelogicboardswithoutheatsinkidentiesnew
version models.
Figure 2 Label for US market – digit 6 on product coding chart
May 2022
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
4Distinguish Old/New Models
Section 3: Distinguish Old/New Models
Figure 3 Example of EPI2 old version (heatsink present)
Figure 4 Example of EPI2 new version (heatsink not present)
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0 May 2022
5
Installation
Section 4: Installation
Section 4: Installation
To assemble the OM11 into the EPI2 actuator, proceed as follows:
• Ensure that all the parts received with the OM11 are available, as described in
Section 12, Optional Kits.
• Using Section 12, Optional Kits, select only mechanical parts (screws and spacers)
depending on actuator models.
• Gather the right tools for the assembly and for setting the actuator controls.
• With an Allen wrench of 5 mm, unscrew the cover screws, see Figure 5.
Figure 5
• Remove the actuator cover, see Figure 6.
Figure 6
Follow one of the following assembling procedures depending on actuator model.
May 2022
Installation, Operation and Maintenance Manual
VCIOM-02377-EN Rev. 0
6Installation
Section 4: Installation
4.1 Assembling Procedure for Models 63-125 Nm
Old Version (US or Non-US Market)
• Detect the black cable required for the OM11 which is already included in the basic
actuator, see Figure 7.
Figure 8
• ConnecttheatcablefurnishedintothekittoconnectorJ3onOM11,see
Figure 8.
Figure 7
Altri manuali per Keystone EPI2
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Emerson Unità di controllo
Emerson
Emerson Keystone Figure 637 Manuale di installazione e funzionamento
Emerson
Emerson Keystone Figure 56 Manuale utente
Emerson
Emerson ANDERSON GREENWOOD 4020HP Manuale
Emerson
Emerson FB1100 Manuale elenco delle parti
Emerson
Emerson Fisherr D2 FloPro Manuale utente
Emerson
Emerson KEYSTONE F635 Istruzioni per l'installazione
Emerson
Emerson Anderson Greenwood 95 Series Manuale utente
Emerson
Emerson Fisher EWNS Manuale utente
Emerson
Emerson Fisher EWD Manuale utente
Emerson
Emerson Baumann 89000 Manuale utente
Emerson
Emerson PENBERTHY FHS Manuale
Emerson
Emerson Yarway 7100 Series Manuale utente
Emerson
Emerson Sapag 1100 Manuale utente
Emerson
Emerson C471 Manuale utente
Emerson
Emerson Liebert iCOM Manuale utente
Emerson
Emerson Keystone Figure 221 Series Manuale utente
Emerson
Emerson Fisher Slurry Vee-Ball V300S Manuale utente
Emerson
Emerson Fisher 92C Manuale utente
Emerson
Emerson AVENTICS AV03 Manuale utente
Emerson
Emerson SW95 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
