Emerson Keystone PED Winn Hiseal Guida rapida
KEYSTONE PED - OPERATING AND SAFETY INSTRUCTIONS
HigH Performance Butterfly ValVes (model Winn Hiseal)
© 2017 Emerson. All rights reserved.
STORAGE/PROTECTION/SELECTION
Storage
When valves are to be stored for some time
before being fitted, storage should be in
theoriginal delivery crates with any waterproof
lining and/or desiccant remaining in place.
Storage should be off the ground in a clean, dry,
indoor area. If storage is for a period exceeding
six months the desiccant bags (if supplied)
should be changed at this interval.
Protection
Valves are delivered with protection according to
customer’s specification, or in accordance with
the Quality Assurance Manual, to protect the
valve seats and closure member from damage.
Wrapping and/or covers should be left in place
until immediately before fitting to the pipe.
Selection
Ensure the valve’s materials of construction
and pressure/temperature limits shown on
the identification plate are suitable for the
process fluid and conditions. If in doubt contact
themanufacturer.
INSTALLATION
WARNING
For safety reasons, it is important to take
thefollowing precautions before you start work on
the valve:
1. Personnel making any adjustments to the
valves should utilize equipment and clothing
normally used to work with the process where
the valve is installed.
2. The line must be depressurized, drained and
vented before installing the valve.
3. Handling and Installation of all valves,
operators and actuators must be carried
out by personnel trained in all aspects of
installation and manual/mechanical handling
techniques.
4. Ensure the valve pressure/temperature
limitations marked on the identification label
are above or equal to service conditions.
Before installation these instructions must be fully read and understood
Installation
1. On-off valves are bi-directional as standard,
unless otherwise stated, and may be fitted
in either direction.
2. Installation may be carried out with stem
displaced through any angle permitted by
the bolting.
3. Spread the flanges to fit the valve easily
(donot use the valve as a crow bar).
4. Remove protective covers from valve faces.
5. Ensure that mating flanges and gaskets are
clean and undamaged.
6. Should there be any possibility of abrasive
particles (weld slag, sand etc.) within the
piping system, this could damage valve
seating areas. The system will need to be
flushed clean.
7. Ensure mating pipe flanges are aligned
correctly, bolting should be easily inserted
through mating flange holes.
8. Fit the valve into pipework ensuring easy
access of the lever/handwheel.
9. Tighten the flange bolts in a diagonal
pattern.
CE Mark in accordance with P.E.D. requirements
Valve identification
code (VIC)
Valve model/size
Works order
number
ASME/ANSI B16.34
Emerson.com/FinalControl VCOSI-01734-EN 18/01
2
!! Read all warning labels fitted to the valve
before operation or maintenance !!
OPERATION AND ROUTINE MAINTENANCE
Scope
These instructions relate to manual and
actuated valves. For special service designs,
typically cryogenic and fugitive emissions see
separate instructions.
Operation
All standard manually operated valves are
‘clockwise to close’. The closed position is
indicated by either the handlever or indicator
arrow being at 90° to the pipe/valve bore axis.
Routine maintenance
No routine maintenance is required other
than periodic inspection to ensure satisfactory
operation and sealing.
Any sign of leakage from the gland packing
should be addressed immediately by
depressurizing the valve and tightening
thegland screws gradually and evenly. If no
further adjustment is possible, or if seat or joint
leakage is suspected, the valve will require a
complete overhaul. This should be carried out
after depressurization and in accordance with
specific maintenance Instructions. Only original
spares should be used.
Spare parts
Valves are identified by a code, which is
stamped on the identification plate, located on
the valve neck. This reference should be quoted
in respect of any after sales queries, spare
parts or repair enquiries/orders.
KEYSTONE PED - OPERATING AND SAFETY INSTRUCTIONS
HigH Performance Butterfly ValVes (model Winn Hiseal)
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product.
Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Keystone is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson
and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by
our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without
notice.
Emerson.com/FinalControl
Altri manuali Emerson Unità di controllo
Emerson
Emerson Keystone OM3 - EPI2 Manuale utente
Emerson
Emerson KTM VIRGO E Series Manuale
Emerson
Emerson NEOTECHA KR Series Guida rapida
Emerson
Emerson Bettis XTE3000 Manuale utente
Emerson
Emerson KTM Series Manuale
Emerson
Emerson Fisher HS Manuale utente
Emerson
Emerson SW95 Manuale utente
Emerson
Emerson SI-I/O Manuale utente
Emerson
Emerson CROSBY STYLE HC ISOFLEX Guida
Emerson
Emerson KEYSTONE FIGURE PCS17 Manuale operativo e di manutenzione
Emerson
Emerson Neotecha Sapro Guida all'installazione
Emerson
Emerson Rosemount RM5800 Manuale utente
Emerson
Emerson KEYSTONE V30 Series Manuale utente
Emerson
Emerson Fisher VS100 Series Manuale utente
Emerson
Emerson Fisher A11 Manuale utente
Emerson
Emerson Sempell S Series Manuale utente
Emerson
Emerson Fisher C407-10 Manuale utente
Emerson
Emerson Bettis Q series Manuale utente
Emerson
Emerson RSTi-OM Manuale utente
Emerson
Emerson Fisher N100 Series Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
