Emerson KTM Series Manuale
KTM SERIES EF190FE SPLIT BODY FLANGED BALL VALVES
INSTALLATION AND MAINTENANCE MANUAL
Before installation these instructions must be fully read and understood
Emerson.com/FinalControl VCIOM-03153-EN 18/07© 2017 Emerson. All Rights Reserved.
1 USE
Long life of valves can be maintained under
normal working conditions and in accordance
with pressure/temperature and corrosion
datachart.
2 MANUAL OPERATIONS
The opening and closing of the valve is done by
turning the handle ¼ turn (90° turn).
A. Valve in open position
The handle is in line with the valve or pipeline.
B. Valve in closed position
The handle is perpendicular with the pipeline.
3 AUTOMATED OPERATIONS
Alignment between actuator and valve is
extremely important.
Misalignment will result high operational
torque, create the stem side loading and cause
early stem leakage.
4 GENERAL INFORMATION FOR ON-SITE
INSTALLATION
4.1 Remove plastic end flanges
protectioncovers.
5 DISASSEMBLY AND CLEANING
PROCEDURES
CAUTION
Ball valves can trap fluids in ball cavity when it is
in closed position.
5.1 If the valve has been used to control
hazardous media, it must be
decontaminated before disassembly. It is
recommended that the following steps be
taken for safe removal and reassemble.
A. Relieve the line pressure.
B. Place valve in half-open position
and flush the line to remove any
hazardous material from valve.
C. All persons involved in the removal
and disassembly of the valve should
wear the proper protective clothing,
such as face shield, glove, and apron,
etc.
5.2 Remove both counter flanges studsand
nuts and lift valve from line for
maintenance.
4.2 The valve may be fitted in any position on
the pipeline.
4.3 Before installing the valves, the pipes
must be flushed clean of dirt, burrs and
welding residues to prevent damage to the
seats and ball surface.
4.4 The pipeline must be free of tension.
5.3 Remove handle (item 18) or actuator set,
stemnut (item 16), lock saddle (item15),
belleville washers (item 14), gland
(item13), thrust washer(item 12) and
stem packing(item 11).
5.4 Remove body stud (item 7) and nuts
(item7a) to allow end cap (item 2)
separated from body (item 1). The ball seat
(item 5) in the end cap should come out.
Remove body gasket(item 6).
5.5 Rotate the stem to "close" position, thus,
the ball (item 3) can be taken out easily
frombody.
5.6 Take out the ball seat (item 5) from body
seatpocket.
5.7 Pull out stem (item 4) and remove the
stem seal (item 8 and 10) compress ring
(item 9). Atthis stage, all the parts are in
"Loose condition" and ready for inspection.
6 VISUAL INSPECTION
Clean and inspect metal parts. It is not
necessary to replace the ball and stem unless
the ball seating surfaces have been damaged
by abrasion or corrosion. Full replacements
of all soft parts are strongly recommended.
Thereplacement parts can be ordered in
"Repair kit" form.
2
(2½"~5")
(6"~12")
KTM SERIES EF190FE SPLIT BODY FLANGED BALL VALVES
INSTALLATION AND MAINTENANCE MANUAL
7 PROCEDURE TO CHANGE PARTS AND
ASSEMBLY
7.1 Install ball seat (item 5) to body (item 1)
seat pocket and make sure the spherical
curvature facing the ball.
7.2 Put lower stem seal (item 8), compress
ring (item 9) and upper stem seal (item10)
to stem (item 4) and slide the stem up
through the body. Install stem packing
(item 11) and top with thrust washer
(item12), gland (item 13), Belleville washer
(item 14), lock saddle (item 15) and drive
stem nut (item 16) per the stem torque
data to ensure the whole stem seals have
been properly compressed. Turn the lock
saddle to engage it with stem nut - this is
to prevent stem nut from unthreading.
7.3 Put the handle (item 18) on stem and
secure it with handle nut (item 16).
7.4 Turn the handle to "close" position. Line
up the ball slots with stem tang and slides
ball (item 3) into the position. Turn the
handle to "open" position to prevent the
ball from falling out.
7.5 Install the body gasket (item 6) into the
shoulder of the end cap (item 2), put the
ball seat (item 5) into seat pocket.
7.6 Put the end cap (item 2) into body with all
the holes line up between or end cap holes
guided by body studs and engaged.
7.7 Finger tight the body stud and nuts and
tighten one side snugly, then the one
diagonally across. Repeat for other bolts
or nuts until the torque is observed per
bolting torque data.
7.8 Cycle the valve slowly with gentle back
and forth motion to build gradually to full
quarter turn. By cycling slowly, the seat
lips will assume a permanent seal shape
against the ball.
7.9 If possible, test the valve before placing
it back to line for service to ensure "No"
through and external leakage is observed.
3
15 ½ M8 195 22 52 6 M5 53 6
20 ¾ M8 195 22 52 6 M5 53 6
25 1 M10 399 45 130 15 M6 74 9
32 1¼ M10 399 45 130 15 M6 74 9
40 1½ M12 700 79 174 20 M8 177 20
50 2 M12 700 79 174 20 M8 177 20
65 2½ M12 700 79 190 22 M10 351 40
80 3 M12 700 79 190 22 M10 351 40
100 4 M12 700 79 260 30 M10 354 40
100 • 4 M16 1222 138 260 30 M10 354 40
125 5 M12 700 79 400 46 M10 354 40
125 • 5 M16 1222 138 400 46 M10 354 40
150 6 M16 1222 138 547 62 M12 575 65
200 8 M16 1222 138 547 62 M12 575 65
200 • 8 M20 3479 393 547 62 M12 575 65
250 10 M16 1222 138 850 97 M16 1097 124
250 • 10 M22 4514 510 850 97 M16 1097 124
300 12 M20 3479 393 850 97 M16 1097 124
300 • 12 M22 4514 510 850 97 M16 1097 124
KTM SERIES EF190FE SPLIT BODY FLANGED BALL VALVES
INSTALLATION AND MAINTENANCE MANUAL
BOLTING TORQUE DATA FOR EF190FE
Valve size For body nut For stem nut* For stem extension bolt or nut
DN NPS Size lbf·in Nm lbf·in Nm Size lbf·in Nm
NOTES
* NPS 4 and smaller stem nut are inch system.
NPS 5 and larger stem nut are metric system.
• For flange end ASME Class 300 and EN PN25/40
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product.
Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
KTM is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson and
the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by
our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without
notice.
Emerson.com/FinalControl
Altri manuali per KTM Series
3
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Emerson Unità di controllo
Emerson
Emerson Fisher Vonk CHV Manuale utente
Emerson
Emerson Daniel 762 Manuale utente
Emerson
Emerson ALCO Thermo TX6 Manuale utente
Emerson
Emerson numatics E22 Manuale utente
Emerson
Emerson ANDERSON GREENWOOD 4142HF Manuale
Emerson
Emerson KEYSTONE OPTISEAL F16 Manuale utente
Emerson
Emerson FASANI Manuale utente
Emerson
Emerson Fisher ME00124272 Guida alla configurazione
Emerson
Emerson Bettis Om3-SCE300 Manuale utente
Emerson
Emerson unidrive m Manuale utente
Emerson
Emerson EIM 2000 Series Manuale utente
Emerson
Emerson Daniel 770 Manuale utente
Emerson
Emerson Yarway Manuale utente
Emerson
Emerson Neotecha Sapro Guida all'installazione
Emerson
Emerson ALCO CONTROLS BVE Series Manuale utente
Emerson
Emerson Alco Controls CVE-014 Manuale utente
Emerson
Emerson Heated Flame Ionization Detector Module Model NGA 2000... Manuale utente
Emerson
Emerson Yarway 9200 Series Manuale utente
Emerson
Emerson FISHER RSS Series Manuale utente
Emerson
Emerson PACSystems RX3i IC695ECM850 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
