EnOcean Capt2web Manuale utente

EnOcean

User manual

November 16, 2009

Contents

1 Introduction 5

1.1 Packet content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 External Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3.1 Ethernet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3.2 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3.3 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Quick start guide 8

2.1 Operation requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 EnOcean 11

3.1 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 User Interface 13

4.1 Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1.1 Packet View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1.2 Table View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1.3 CSV View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1.4 Timeline View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1.5 Detail View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.2 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5 On-line data logging 17

6 Settings 19

6.1 Monitoring Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.2 IP address settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7 USB console 22

7.1 Installing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

7.2 Connecting to the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7.3 Using the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7.4 Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8 Troubleshooting tips 28

9 Important information 29

9.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9.2 No warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9.3 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9.4 Disclaimer of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9.5 Copyright for the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9.6 Disclaimer for the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9.7 Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Conformity 32

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

List of Tables

1.1 Packet content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 capt2web speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.1 List of EnOcean Radio Protocol ﬁelds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2 List capture information ﬁelds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.3 List of EnOcean Radio Protocol types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

List of Figures

2.1 capt2web hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 capt2web main application screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1 Example of a captured packet in the packet view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.1 Packet View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Table View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3 CSV View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.4 Timeline View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.5 Detail View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.6 Deﬁning a ﬁlter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.7 Deﬁning several rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1 USB view in the web interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.1 Static IP address settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.2 Automatic IP address conﬁguration using DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.1 Windows Hardware Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

7.2 Choose Location Dialog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

7.3 capt2web Hardware was found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

7.4 Properly installed capt2web module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

7.5 Screen shot of the console interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

7.6 Link to ﬁrmware update page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

7.7 Firmware update site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

Chapter 1

Introduction

capt2web is a device to monitor wireless networks. Due to its small form factor it can be placed right in the best place

for wireless network trafﬁc to be monitored. It provides a full-featured web based capture monitor software that

runs in all common web-browsers. Thus, the monitoring software can be accessed using any computer, independent

from the computer’s operating system. For common operation, neither hardware nor software installation applies

for the monitoring computer.

This document covers instructions for the use of capt2web . The ﬁrst chapter contains the speciﬁcations of capt2web

. A quick start guide follows, that describes in short terms how to get capt2web into operation for the ﬁrst time. In

the third part, the web interface, being the main user interface, is described. Especially focussing on the different

views of captured data.

The following chapters cover additional features such as data logging on an USB mass storage, console mode for

conﬁguration and the ﬁrmware update.

Please make sure to read the instructions carefully.

If there are still open questions after reading this manual, contact STZEDN for support.

1.1 Packet content

Item Comment

capt2web module Hardware device for wireless protocol monitoring

Power supply 230VAC /6.0VDC, 800mA

Support CD CD containing manuals and the USB driver, necessary for console connection

CAT5 Ethernet cable

Mini-USB-A plug to USB-A socket adaptor to attach a USB mass storage device

USB extension for mass storage device connection

USB-A to Mini-USB cable to connect to capt2web with the console

Table 1.1: Packet content

Please, only use the cables and adaptors provided together with capt2web .

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

CHAPTER 1. INTRODUCTION page 6

1.2 Speciﬁcations

Parameter Minimum Typical Maximum

Module dimensions

Length 117 mm

Width 79 mm

Height 24 mm

Power Requirements

Supply voltage 5.5V DC 6.0V DC 7.5V DC

Current consumption 200mA 350mA 450mA

Environmental conditions

Temperature Range 0◦C 25◦C 40◦C

Table 1.2: capt2web speciﬁcations

1.3 External Interfaces

1.3.1 Ethernet connection

The capt2web module contains a full duplex 10/100Mbps Ethernet interface. Use the CAT5 cable supplied to connect

the device to an Ethernet switch or directly to a computer. The interface is Auto-MDIX capable. It requires no special

cable, such as a crossover cable, to directly connect it to a computer, but the connection type is automatically

recognized.

Instructions for the conﬁguration of the Ethernet interface, especially IP settings, can be found in chapter 6and 7.3.

1.3.2 USB interface

capt2web provides a full-speed USB on-the-go port on its Mini-USB connector. The USB on-the-go (OTG) functionality

allows the capt2web module either to act as an USB device or Host depending on the type of end point connected to

it. This provides maximum ﬂexibility.

Host mode: the port supports USB mass storage devices for continuous data logging. See chapter 5for details.

Client Mode: capt2web module acts as a CDC device providing a console interface to conﬁgure your device and

display information about it. See chapter 7for details.

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

CHAPTER 1. INTRODUCTION page 7

1.3.3 Power Supply

capt2web can be powered either using the power adaptor provided (5.5V to 7.5V DC, center positive) or over a USB

CDC connection. As the power consumption is up to 450mA, the power supply over the USB interface requires an

active USB hub. Please use primarily the AC-DC adaptor provided with capt2web to guarantee its function. Both

power supplies can be connected in parallel without any interaction. When connecting capt2web for the ﬁrst time to

a computer, make sure that the AC-DC adaptor is attached to permit proper installing of the CDC drivers.

For a mass storage device attached to the USB port, make sure to consume less than 100mA. In case of doubt, please

contact STZEDN before attaching devices.

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

Chapter 2

Quick start guide

2.1 Operation requirements

In order to operate the capt2web , you must have the following:

•A computer equiped with a network port (network adaptor: standard Ethernet 10/100 Base-T)

•A compatible web browser. capt2web was tested with the following browsers:

–Mozilla Firefox 3.x or higher

–Microsoft Internet Explorer 6 and higher

–Opera 9.6x or higher

–Safari 4 or higher

•A reader for PDF-documents to access the documentation.

For conﬁguring capt2web using the console interface, you further need:

•A USB port

•The required user privileges to install the CDC drivers (only once).

Long-term data logging further requires a formatted USB mass storage device (USB memory stick). The data on the

storage are not deleted due to logging. Please do not use a bus-powered USB hard disk together with capt2web to

prevent damage.

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

CHAPTER 2. QUICK START GUIDE page 9

2.2 Installation

Figure 2.1: capt2web hardware

1. Connect the power supply unit to the socket labelled "Power"

2. Plug the power supply in a 230VAC outlet.

åThe green power LED inside capt2web will be turned on, when powered.

3. Network connection for capt2web

(a) Assign a static IP address within the range of capt2web ’s address to your computer and establish a direct

connection using the provided Ethernet patch cable.

(b) Connect capt2web to your local network using the provided Ethernet patch cable.

Each capt2web is conﬁgured with a default static IP address. It is printed on the

back label on the capt2web ; this address can also be changed permanently. If the

address conﬁguration is not matching your network settings (IP address and/or sub

net mask), please conﬁgure the IP address using the console as described in the cor-

responding chapter of the user manual. Please contact your local network adminis-

trator before connecting any network device to your network.

4. Start a web browser and type the IP address of capt2web in the address ﬁeld.

5. Start a capture by pressing the "Start" button on the web page.

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

CHAPTER 2. QUICK START GUIDE page 10

Figure 2.2: capt2web main application screen

Steinbeis Transfer Center Embedded Design and Networking

Baden-Württemberg Cooperative State University Lörrach

Prof. Dr.-Ing. Axel Sikora

Indice

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente

EnOcean capt2web Manuale utente

Manuali Strumento di misura popolari di altre marche