EOS SBM App Module Manuale di istruzioni

Indice

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21

EOS SBM App Module

General guide for setup and operation

Before the setup

Install the SBM App module and connect it to the sauna control unit with the pre-mounted sauna bus

cable (requires a free RJ12 sauna bus connector in the sauna control unit). Connect the module to

your router / cable modem (internet access point) using a standard Ethernet cable (RJ45). Make sure

the internet connection is available and is not blocked by the firewall (port 7250 should be available).

Make sure the sauna control unit has been set up correctly and remote control has been cleared

during initial setup.

01 Setup preparation

Download the free “EOS Spa Control” app on your mobile device from the Google PlayStore or Apple

AppStore and install it. Keep the sauna control unit and the SBM App module powered (stand by

mode). Launch the app. Self-guided setup process will lead you through all steps.

02 Welcome screen

Welcome to the setup of your EOS Spa Control app. Tap on “launch setup”

button to start.

03 MAC address

For setup and pairing you will need an individual MAC address. This

address you can find printed on the type shield attached on the SBM App

module.

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21

03 Enter the MAC address

Pairing step 1

Give in the last three pairs of the individual MAC address in the

corresponding fields.

„Where do I find the MAC address“ – press to get help with locating the

MAC address.

Tap on “Start pairing” to initiate the pairing sequence. Hold on a pointed

tool, e.g. a paper clip, ready.

04 Press the pairing button

Pairing step 2

Now press firmly on the pairing button on the SBM App module with a

pointed tool (e.g. paper clip end) for 1 second.

You need to do this within 60 seconds. The countdown will be displayed

on the app screen.

05 Pairing successful

Pairing step 3

If the pairing has been successful, the appropriate confirmation screen

will be displayed. Otherwise repeat the pairing.

You mobile device is now successfully paired with the app module (with

your sauna control unit).

Tap on “Next” to finalize the setup.

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21

06 Name your sauna

Pairing step 4

Here you can assign a name to your sauna, for instance “My Sauna”.

To complete the setup tap on the “to the control” button.

How to control your sauna with the app

01 Start you sauna

To unlock the app and start your sauna (start heating) press and hold

both buttons for 3 seconds.

02 Faulty connection

If the app has lost connection to the SBM App module, e.g. no internet

connection or due to a connection fault, an error message will be shown:

“No connection to the sauna can be established at the moment. Please try

again later”.

The app will try to reconnect automatically. The error message will

disappear once the connection has been re-established.

EOS SBM App module and EOS Spa Control app – quick start up guide Print no. 2934 4672 13.21

03 Sauna being started

While the start or stop command is being transmitted to the sauna control

unit a temporary overlay screen „your sauna is being switched on“ will be

displayed.

04 Climate settings

If you have a dry Finnish sauna or a sauna with

humidity operation the climate settings interface

will accordingly display the settings for

temperature only (right image) or temperature

and humidity (left image). Use +/- to adjust.

You can also switch light and stop the heating

through the corresponding buttons.

Current climate values will be displayed in the

upper area.

05 Other settings

Press the cog symbol the upper right corner to check the global

parameters, such as the sauna cabin name, paired MAC address and the

app version.

In this submenu you can delete the pairing – for this press on “disconnect

sauna”.