EOS EOS-500 Manuale utente
Rev_A
P a g e 1 | 9
1
EOS-500
Marine Anemometer
Rev_A
P a g e 2 | 9
2
DISCLAIMER
Neither EOS Weather instruments nor its affiliates shall be liable to the purchaser
of this product or third parties for damages, losses, costs, or expenses incurred by
purchaser or third parties as a result of use, misuse, accident, or abuse.
Notwithstanding the above EOS Weather Instruments liability shall not exceed the
purchase price of the equipment.
THIS EQUIPMENT IS NOT TO BE USED FOR SAFETY PURPOSES
USE OF THIS PRODUCT SHALL BE DEEMED TO BE ACCEPTANCE OF EOS WEATHER
INSTRUMENTS STANDARD TERMS AND CONDITIONS (ENCLOSED AND AVAILABLE
AT WWW.EOSWEATHER.CA).
IF YOU DO NOT AGREE TO BE BOUND BY THESE TERMS AND CONDITIONS PLEASE
RETURN THIS PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND
ADVISORY USE ONLY
This equipment does not include self-test circuitry to
warn of loss of functionality. Additional measures
should be in place to safeguard personnel or equipment.
Rev_A
P a g e 3 | 9
3
Table of Contents
1. Introduction
2. Installation
2.1. Required tools
2.2. Pre-assembly of the Windvane
2.3. Pre-assembly of the Anemometer
2.4. Installing the EOS-500
2.5. Electrical connection
3. The IR-761 Display
3.1. Display operation
3.2. Indications Alarms
4. Specifications
4.1. Electrical Specifications
Rev_A
P a g e 4 | 9
4
1. Introduction
Thank you for choosing the EOS-500 Marine Anemometer from EOS Weather Instruments.
EOS has designed and built the EOS-500 to the highest standards for years of reliable, dependable, and
accurate service. The EOS-500 is designed to operate within the harsh demands of the marine
environment. However, no piece of marine electronic equipment can function properly unless installed
and maintained in the correct manner. Please read carefully and follow these instructions for
installation and usage of the EOS-500 in order to ensure optimal performance.
The signal from the EOS-500 is a standard NMEA 0183 signal and can directly be transmitted to any
device accepting the NMEA 0183 protocol. The EOS-500 only provides relative wind speed and direction.
2. Installation
The EOS-500 is a high accurate Anemometer and includes various sensitive parts. Great care must be
taken when handling and installing this high precision equipment. Installation is easy, however
following safety advice should be adhered to:
-Do NOT install your system near any power- or any other utility lines.
-Do NOT install the Anemometer before taking all necessary safety pre-cautions.
-Ensure a free flow of wind around the sensor
After unpacking the system from its packaging carefully observe that no damages are visible. If any
damaged equipment is observed, immediately contact us.
After unpacking your shipment, ensure the following parts are inside the packaging:
oMain unit incl. 60’ (18m) cable
oWind vane
oAnemometer cups
-IR 761 Display unit incl. mounting hardware
-Power cable
-2 x stainless steel U-Bolts
-This manual
Rev_A
P a g e 5 | 9
5
2.1 Required Tools
For ease of installation, the EOS-500 is partially pre-assembled. Some minor assembly is required. The
included mounting hardware makes the installation easy and quick. The tools required for the
installation:
-Regular (-) screw driver
-Wrench (12mm or 1/2”)
2.2. Pre-assembly of the Wind vane.
For the ease of shipping of your station, the Wind vane and the Anemometer cups have been removed.
-Line up the arrow on the top shaft with the “N” on the housing.
-Gently push the wind vane onto the shaft with the point aligned to the “N”
-Ensure that the vane is properly seated on the shaft.
-Secure the vane by tightening the point of the wind vane.
oDON’T OVERTIGHTEN THIS !
Rev_A
P a g e 6 | 9
6
2.3. Pre-assembly of the Anemometer.
-Insert the cup assembly onto the shaft and secure the screw.
-Ensure that the cup assembly is properly seated on the shaft.
oDON’T OVERTIGHTEN THE SCREW !
2.4. Installing the EOS-500.
The pole for the Wind vane / anemometer should be about 2” (5 cm) in diameter. Ensure that the pole
you select for the unit is strong enough to withstand high winds and will not cause any bending or
vibration.
-Use a wrench to secure the ¼” U-bolts.
-Ensure that the “N” on the housing will point towards North or the Bow of the vessel.
Rev_A
P a g e 7 | 9
7
2.5. Electrical Connection
WARNING: Supply voltage should NOT exceed 36V. Also, do NOT reverse polarity; this will harm the
equipment.
IMPORTANT: Ensure that the ground wire is properly connected to the vessels ground
PAIR
COLOR
FUNCTION
1
RED
DC + (12 –36V Dc)
1
BLACK
DC -
2
WHITE
NMEA +
2
BLACK
NMEA -
GROUND
Ground
3. The IR-761 Display
Relative Wind Direction
Relative Wind direction variation
Relative Wind Speed
Speed Unit
Max. Wind Speed
Rev_A
P a g e 8 | 9
8
3.1. Display operation
“S” Key: Select Key
Switch / Select between wind speed units: m/s, knots, km/h, mph
“ “ Key: Backlight DIM control.
“F” Key: Function Key
Will alternate between: “Relative Mode”, True Mode”, and “Relative, Max wind interval setting Mode”
In the “Relative, Max wind interval setting Mode”, use the keys to select the wind speed interval
between 1, 2, 5 and 10 minutes.
NOTE: “True Mode”; This selection will show “ERR” when connected directly to the EOS-500.
3.2. Indications / Alarms
ERR: “ERR” indications that the display doesn’t receive any NMEA data, or the data is
incorrect. The “ERR” will also occur in case “TRUE” is selected but no true wind data is
received.
“- - --“Incorrect data
“_ _ _” NMEA is received but other than the required “MWV”
Rev_A
P a g e 9 | 9
9
4. Specification
EOS-500
IR-761
Wind Speed Range
1 –95 knots (1.8 –176 km/h)
0 –99.9 m/s, km/h, knt, mph
Wind Speed Resolution
0.1 knot (0.2 km/h)
0.1
Wind Speed accuracy
1 knot (2 km/h)
Wind Direction accuracy
1 degree
Wind Direction resolution
0.1 degree
10 degrees
4.1 Electrical Specifications
EOS-500
IR-761
Operating Voltage
9 –36VDc
12 –36 VDC
Power consumption
<100mW
2 W
EOS Weather Instruments
102 Chain Lake Drive, Unit 5
Halifax, Nova Scotia
B3S 1A7
Canada
TEL: +1 (902) 982 6652
Indice
Altri manuali EOS Strumento di misura
