Epson S5U13L01P00C100 Manuale utente

SEIKO EPSON CORPORATION Rev. 1.0

S1D13L01 Display Controller

S5U13L01P00C100

Evaluation Board User

Manual

Downloaded from Arrow.com.

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko

Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any lia-

bility of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or cir-

cuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as,

medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is

no representation or warranty that anything made in accordance with this material will be free from any patent or copyright

infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic

products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from

the Ministry of International Trade and Industry or other approval from another government agency.

All other product names mentioned herein are trademarks and/or registered trademarks of their respective companies.

Downloaded from Arrow.com.Downloaded from Arrow.com.

S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 3

Table of Contents

Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 CNF[2:0] Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2 Configuration Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

3.3 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3.4 Zero Ohm Resistor Configuration . . . . . . . . . . . . . . . . . . . . . . . 11

3.5 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.1 IOVDD, COREVDD, PLLVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.2 3.3V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.3 Backlight Power Supply for LCD Panel . . . . . . . . . . . . . . . . . . . . . . . 11

3.6 LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 4 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1 CN1, CN2, CN5 Panel Interface Connector . . . . . . . . . . . . . . . . . . . 14

4.2 CN3, CN4 Host Bus Interface Connector . . . . . . . . . . . . . . . . . . . . 14

4.3 P1, P2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board . . . . . . 15

Chapter 5 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.1 Current Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2 Oscillator Support for CLKI input . . . . . . . . . . . . . . . . . . . . . . 17

5.3 Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Chapter 6 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Chapter 7 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 8 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Chapter 9 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4 EPSON S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0)

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Chapter 1 Introduction

S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 5

Chapter 1 Introduction

This manual describes the setup and operation of the S5U13L01P00C100 Evaluation Board. The evaluation board

is designed as an evaluation platform for the S5U13L01 Display Controller.

The S5U13L01P00C100 evaluation board can also connect to the S5U13U00P00C100 USB Adapter board so that

it can be used with a laptop or desktop computer, via USB 2.0. The S5U13L01P00C100 evaluation board can be

used with many native platforms via the host connector which provides the appropriate signals to support a variety

of CPUs. However, if you do not use the S5U13U00P00C100 USB Adapter board, there are locations for connectors

for the other host interface. Please use the alocated locations to connect to the host interface.

This user manual is updated as appropriate. Please check the Epson Electronics America Website at vdc.epson.com

for the latest revision of this document before beginning any development.

We appreciate your comments on our documentation. Please contact us via email at documen-

tation@eea.epson.com.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Chapter 2 Features

6 EPSON S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0)

Chapter 2 Features

The S5U13L01P00C100 Evaluation Board includes the following features:

• QFP 128pin S1D13L01F00A100 Display Controller

• Headers for connection to the S5U13U00P00C100 USB Adapter board

Note

The SPI interface is not available when the S5U13L01P00C100 evaluation board is used with the

S5U13U00P00C100 USB adapter board.

• Headers for connection to various host interface

Note

These headers are not mounted. There is space available for mounting.

• Headers for connection to various LCD panels

• On-board 24MHz crystal (EPSON SG-210)

• On-board voltage regulator with 1.5V output, for CORE/PLLVDD

• On-board voltage regulator with adjustable 1.5~3.8V output, for IOVDD

• On-board voltage regulator with 3.3V output, for on-board OSC

• On-board voltage regulator with adjustable 38V/60mA max, to provide power for LED back-light of LCD

panels.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Chapter 3 Installation and Configuration

S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 7

Chapter 3 Installation and Configuration

The S5U13L01P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm resistors which allow it

to be used with a variety of different configurations.

3.1 CNF[2:0] Configuration

The S1D13L01 has 3 configuration inputs CNF[2:0], whichare usedto configure the S1D13L01 host interface type

through DIP switch SW1. Depending on the CNF[2:0] setting, some host interface pins will not be used. Those pins

should be terminated by SW2 and SW3.

Note

1. For SW2~3, the setting must be Off if there is no suggestion in table.

2. For JP105~109, the setting must be 1-2 if there is no suggestion in table.

3. Low means internal pull-down for address bus active.

4. The SPI interface is not available when the S5U13L01P00C100 evaluation board is used with the

S5U13U00P00C100 USB adapter board.

Table 3-1: Host Interface Pin Mapping

S1D13L01

Pin Name Direct 16-bit

Mode 1 Direct 16-bit

Mode 2 Indirect 16-bit

Mode 1 Indirect 16-bit

Mode 2 Direct 8-bit Indirect 8-bit SPI

CNF[2:0] 000 001 010 011 100 101 111

CS# CS# CS# CS# CS# CS# CS# CS#

WR# WR# RDU# WR# RDU# WR# WR# SCK

RD# RD# RDL# RD# RDL# RD# RD# SW2-3=On

UB# UB# WRU# UB# WRU# SW2-1=On SW2-1=On SW2-1=On

LB# LB# WRL# LB# WRL# SW2-2=On SW2-2=On SW2-2=On

AB0 TE (JP108 2-3) TE (JP108 2-3) TE (JP108 2-3) TE (JP108 2-3) AB0 TE (JP108 2-3) TE (JP108 2-3)

AB1 AB1 AB1 P/C# P/C# AB1 P/C# Low

AB[18:2] AB[18:2] AB[18:2] Low Low AB[18:2] Low Low

DB0 DB0 DB0 DB0 DB0 DB0 DB0 SI

DB1 DB1 DB1 DB1 DB1 DB1 DB1 SO

DB[7:2] DB[7:2] DB[7:2] DB[7:2] DB[7:2] DB[7:2] DB[7:2] SW2-5~10=On

DB8 DB8 DB8 DB8 DB8 TE (JP108 3-4) SW3-1=On SW3-1=On

DB[15:9] DB[15:9] DB[15:9] DB[15:9] DB[15:9] SW3-2~8=On SW3-2~8=On SW3-2~8=On

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Chapter 3 Installation and Configuration

8 EPSON S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0)

3.2 Configuration Switches

The S5U13L01P00C100 evaluation board includes the following switch blocks which control the functions

described in Table 3-2: “Switch Settings”. For jumper locations on the evaluation board, see Figure 3-1: “Configu-

ration Switch and Jumper Locations (Red)” on page 10.

Table 3-2: Switch Settings

Switch bit On Off Comment

SW1

1CNF0 is Pull Up (1) CNF0 is Pull Down (0) CNF[2:0] configuration. See Table

3-1: “Host Interface Pin Mapping”

2CNF1 is Pull Up (1) CNF1 is Pull Down (0)

3CNF2 is Pull Up (1) CNF2 is Pull Down (0)

4not used not used

SW2

1UB# is Pull Up UB# is not tied

Host interface pin termination when

not used pin. See Table 3-1: “Host

Interface Pin Mapping”

2LB# is Pull Up LB# is not tied

3RD# is Pull Up RD# is not tied

4not used not used

5DB2 is Pull Down DB2 is not tied

6DB3 is Pull Down DB3 is not tied

7DB4 is Pull Down DB4 is not tied

8DB5 is Pull Down DB5 is not tied

9DB6 is Pull Down DB6 is not tied

10 DB7 is Pull Down DB7 is not tied

SW3

1DB8 is Pull Down DB8 is not tied

2DB9 is Pull Down DB9 is not tied

3DB10 is Pull Down DB10 is not tied

4DB11 is Pull Down DB11 is not tied

5DB12 is Pull Down DB12 is not tied

6DB13 is Pull Down DB13 is not tied

7DB14 is Pull Down DB14 is not tied

8DB15 is Pull Down DB15 is not tied

= suggested settings

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Chapter 3 Installation and Configuration

S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 9

3.3 Configuration Jumpers

The S5U13L01P00C100 evaluation board includesthe following 2-pin, 3-pin, 5-pin and 8-pin jumper blocks which

control the functions described in Table 3-3: “2-Pin Jumper Settings”, Table 3-4: “3-Pin Jumper Settings” , Table

3-5: “5-Pin Jumper Settings” and Table 3-6: “8-PinJumper Setting”. For jumper locations on the evaluation board,

see Figure 3-1: “Configuration Switch and Jumper Locations (Red)” on page 10.

Note

For normal S5U13L01P00C100 operation, JP102 should be in Position 1-2. Also, when using the

S5U13L01P00C100 with the S5U13U00P00C100, JP102 should be in Position 1-2 (JP1 on the

S5U13U00P00C100 must be in Position 1-2). For IOVDD current measurement, JP102 should be removed.

Table 3-5: 5-Pin Jumper Settings

Table 3-3: 2-Pin Jumper Settings

Jumper Position 1-2 No Jumper (Open)

JP101 Connect COREVDD Power Supply Connect a current meter for power measurement

JP102 NOTE Connect IOVDD Power Supply to S5U13U00P00C100 No IOVDD Power Supply to S5U13U00P00C100

JP104 Connect PLLVDD Power Supply Connect a current meter for power measurement

= suggested settings

Table 3-4: 3-Pin Jumper Settings

Jumper Position 1-2 Position 2-3 Off

JP105 WR# is from P1 and CN3 WR# is from P2 WR# is not connected

JP106 DB0 is from P1 and CN3 DB0 is from P2 DB0 is not connected

JP107 DB1 is from P1 and CN3 DB1 is from P2 DB1 is not connected

= suggested settings

Jumper Position Function

JP108 Position 1-2 Position 2-3 Position 1-2: AB0 is AB0 (only for Direct 8bit mode)

Position 2-3: AB0 is TE

Position 3-4 Position 4-5 Position 3-4: DB8 is TE (only for Direct 8bit mode)

Position 4-5: DB8 is DB8

= suggested settings

Chapter 3 Installation and Configuration

10 EPSON S5U13L01P00C100 Evaluation Board User Manual (Rev. 1.0)

Table 3-6: 8-PinJumper Setting

Figure 3-1: Configuration Switch and Jumper Locations (Red)

Jumper Position Function

JP503

Position 1-2 No Jumper In connect case, TPS61161A is Enable

Position 3-4 No Jumper In connect case, Vout = 20mA

Position 5-6 No Jumper In connect case, Vout = 40mA (add connect Position 3-4)

Position 7-8 No Jumper In connect case, Vout = 60mA (add connect Position3-4 and

Position5-6)

= suggested settings

Altri manuali per S5U13L01P00C100

Indice

Altri manuali Epson Scheda madre

Epson

Epson S5U13U11 Manuale utente

Epson

Epson S5U13T04P00C100 Manuale utente

Epson

Epson S1D13709 Manuale utente

Epson

Epson S5U13700B00C Manuale utente

Epson

Epson S5U13781R01C100 Manuale utente

Epson

Epson S5U13L02P00C100 Manuale utente

Epson

Epson S5U1C31D50T1 Manuale utente

Epson

Epson S1D13513 Manuale utente

Epson

Epson S1V3034x Series Guida

Epson

Epson S1R72V27 Manuale utente

Epson

Epson S5U13706P00C100 Manuale utente

Epson

Epson S5U13742P00C100 Manuale utente

Epson

Epson S1D13C00 Manuale utente

Epson

Epson S5U13A05B00C Manuale utente

Epson

Epson S5U13700B00C Manuale utente

Epson

Epson S1D13706 Manuale utente

Epson

Epson S1R72U16 Manuale utente

Epson

Epson S5U13515P00C100 Manuale utente

Epson

Epson S5U13A04B00C Manuale utente

Epson

Epson S5U1C31D51T1 Manuale utente

Epson

Epson S5U13706P00C100 Manuale utente

Epson

Epson S5U1C17M03T Manuale utente

Epson

Epson S5U13705B00C Manuale utente

Epson

Epson S5U13781R00C100 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente