Ero electronic ESR Manuale utente

ESR

ESR-T

ETR

170.IU0.ESR.0A02-01/B

rUSER MANUAL

rMANUEL DE SERVICE

rBEDIENUNGSANLEITUNG

rISTRUZIONI D'USO

EXR-0-02.p65 2/28/01, 4:52 PM1

INDEX

ASSEMBLING ..................................................... 1

WARNINGS ................................................. 1

General assembling information ................. 1

Wall mounting .............................................. 3

Omega din rail mounting ............................. 4

CONNECTION DIAGRAMS ................................ 5

GENERAL NOTES FOR WIRING ............... 5

WARNING ................................................... 5

Power Þnominal current conversion .......... 8

CONNECTIONS ................................................. 9

Single phase connection ............................. 9

Three phase without neutral connections .. 10

Three phase with neutral connections ....... 11

ETR connection ......................................... 13

GENERAL SPECIFICATIONS .......................... 14

CHARACTERISTICS OF THE ESR-T .............. 15

CHARACTERISTICS OF THE ESR ................. 16

CHARACTERISTICS OF THE ETR .................. 17

MAINTENANCE ................................................ 18

APPENDIX A

Dimensions and panel cut out ..................A.1

INDEX

MONTAGE .......................................................... 1

INSTRUCTIONS .......................................... 1

Normes generales pour le montage ............ 1

Montage mural ............................................. 3

Montage au moyen d'une barre OMEGA .... 4

RACCORDEMENTS ELECTRIQUES ................ 5

NOTES GENERALES

POUR LE RACCORDEMENT ..................... 5

INSTRUCTIONS .......................................... 5

La conversion

puissance Þ courant nominal ..................... 8

RACCORDEMENTS ........................................... 9

Raccordement monophasé .......................... 9

Reccordements triphasés sans neutre ...... 10

Raccordements triphasés avec neutre ...... 11

Raccordements pour ETR ......................... 13

DONNES TECHNIQUES COMMUNES ............ 14

CARACTERISTIQUES DES MODELES ESR-T15

CARACTERISTIQUES DES MODELES ESR .. 16

CARACTERISTIQUES DES MODELES ETR .. 17

ENTRETIEN ...................................................... 18

APPENDIX A

Dimensions et percages ................................... A1

EXR-0-02.p65 2/28/01, 1:04 PM2

INDICE

MONTAGGIO ...................................................... 1

AVVERTENZE ............................................. 1

Norme generali per il fissaggio .................... 1

Fissaggio a parete ....................................... 3

Fissaggio tramite barra OMEGA ................. 4

COLLEGAMENTI ELETTRICI ............................ 5

NOTE GENERALI PER IL

COLLEGAMENTO ....................................... 5

AVVERTENZE ............................................. 5

La conversione

potenzaÞcorrente nominale ....................... 8

COLLEGAMENTI ................................................ 9

Collegamento monofase .............................. 9

Collegamenti trifase senza neutro ............. 10

Collegamenti trifase con neutro ................. 11

Collegamento per ETR .............................. 13

DATI TECNICI COMUNI ................................... 14

CARATTERISTICHE DEI MODELLI ESR-T ..... 15

CARATTERISTICHE DEI MODELLI ESR ........ 16

CARATTERISTICHE DEI MODELLI ETR ........ 17

MANUTENZIONE ............................................. 18

APPENDIX A

Dimensioni e forature ................................ A1

INHALTSVERZEICHNIS

MONTAGE .......................................................... 1

HINWEISE ................................................... 1

Allgemeine Montagevorschriften ................. 1

Wandmontage ............................................. 3

Montage mit OMEGA-Schiene .................... 4

ELEKTRISCHE ANSCHLÜSSE .......................... 5

ALLGEMEINE ANMERKUNGEN ZUM

ANSCHLUSS ............................................... 5

HINWEISE ................................................... 5

Die Umformung Leistung ÞNennstrom ...... 8

ANSCHLÜSSE .................................................... 9

Einphasiger Anschluß .................................. 9

Dreiphasige Anschlüsse ohne

Sternpunktleiter ......................................... 10

Dreiphasige Anschlüsse mit

Sternpunktleiter ......................................... 11

Anschlüsse für ETR ................................... 13

ALLGEMEINE TECHNISCHE DATEN ............. 14

LEISTUNGSMERKMALE VON DEN ESR-T .... 15

LEISTUNGSMERKMALE VON DEN ESR ........ 16

LEISTUNGSMERKMALE VON DEN ETR ........ 17

WARTUNG ....................................................... 18

APPENDIX A

Abmessungen ............................................ A1

EXR-0-02.p65 2/28/01, 1:04 PM3

ASSEMBLING

WARNINGS:

1) The correct functionality of these devices is

guaranteed only if transport, storage,

installation, wiring, working condition and

maintenance are executed in compliance with

this manual.

2) The protection degree of these devices is

equal to IP 20 (according to CEI EN 60529)

and they are connected to dangerous power

lines, for these reasons:

- installation, wiring and maintenance must be

executed by qualified personnel;

- all warnings contained in this manual must

be complied.

3) Do not execute any dielectric strength or

insulation resistance test on the power

terminals.

These type of tests could damage the power

semiconductors.

4) Circuit-breaker:

- a switch or circuit-breaker shall be included in

the building installation;

- It shall be in close proximity to the equipment

and within easy reach of the operator;

- it shall be marked as the disconnecting device

for the equipment.

NOTE: a single switch or circuit-breaker can

drive more than one device.

5) Before to execute any operation on the load or its

connections, disconnect the device from the

power line by the circuit breaker.

6) During continuous operation, the heat sink could

reach a temperature higher than 80 °C (176 °F)

Before execute any operation to the device, you

have to be sure that its temperature is decreased

to an acceptable value.

7) For placing the device, choose a cleaned

position, easy to reach, and possibly without

vibration.

8) The ambient temperature must be comprised

between 0 °C and 40 °C (32 to 104 °F).

GENERAL ASSEMBLING INFORMATIONS

1) These devices must be assembled vertically or

with a maximum inclination of 20°.

Fig. 1

EXR-1-02.p65 2/28/01, 1:04 PM1

Fig. 2

2) In order to allow a sufficient heat dissipation,

these devices must be spaced 100 mm out to

the bottom and 150 mm out to the top of the

cabinet or any other element (I.E. raceway)

which can compromise the air flow.

Fig. 3

EXR-1-02.p65 2/28/01, 1:04 PM2

3) The manufacturer strongly recommends

against to assemble two or more devices one

upon another but, if necessary, the distance

between the two devices must be longer than

400 mm.

Fig. 4

The device can be mounted either on wall or on a

Omega DIN rail.

WALL MOUNTING

For wall mounting you can use the (A) holes.

ESR/ESR-T ETR

In this case it is advisable to use M4 screws with

a torque of 1Nm.

For the mounting template and the mechanical

dimensions of all models, please refer to the

appropriate drawing, located in the "Mechanical

dimensions" paragraph.

(A)

(A) (A)

(A)

EXR-1-02.p65 2/28/01, 1:04 PM3

OMEGA DIN RAIL MOUNTING

For rail mounting use an Omega DIN rail in

accordance with EN 50 022 (35 x 7.5 mm or 35 x

15 mm) regulations.

MOUNTING

Fig. 5

REMOVING

Fig. 6

For the mechanical dimensions of all models,

please refer to the appropriate drawing, located in

the Appendix A.

screwdriver

Omega

DIN rail

EXR-1-02.p65 2/28/01, 1:04 PM4

Table 1

ESR/ETR Fuse

Model Manuf. model

Ferraz 6600CPURGA22X58/32

25 - 400 Bussmann FWP.32A.22F

Gould 52443

Ferraz 6600CPURGA22X58/50

40 - 400 Bussmann FWP.50A.22F

Gould 53251

Ferraz 6600CPURGA22X58/80

60 - 400 Bussmann FWP.80A.22F

Gould 53259

Ferraz 6600CPURGA22X58/100

80 - 400 Bussmann FWP.100A.22F

Gould 53263

25 - 600 Ferraz 6600CPURD22X58/32

40 - 600 Ferraz 6600CPURD22X58/50

60 - 600 Ferraz 6600CPURD22X58/80

80 - 600 Ferraz 6600CPURD22X58/100

CONNECTION DIAGRAMS

GENERAL NOTES FOR WIRING

WARNINGS:

1) The wiring must be executed only after you have

mounted the device correctly.

2) Before connecting the device, you have to be

sure that the power line voltage value is less

than the nominal value reported on the

device's identification label.

3) Before connecting the device, you have to be

sure that the current absorbed by the load (see

Power Þnominal current conversion para-

graph) is less than the device nominal current as

a function of the ambient temperature and the

Duty cycle (see Trend of the nominal current in

relation with the ambient temperature and

duty cycle paragraph).

4) Before execute any operations, be absolutely

sure that the device is disconnected from the

power line through the circuit breaker.

5) Use copper wires only.

6) Do not care to the input command polarity;

the + (terminal 5) and - (terminal 6) marks are

indicative only.

7) The power input IS NOT fuse protected; so it is

necessary placing an external one selected

among the types shown in Table 1( for ESR

and ETR) or Table 2 (for ESR-T).

NOTE:

The Manufacturer decline any responsibility for

injury and/or property damage if NO fuse or

fuse not included in Table 1 and 2 is used.

The warranty validity also depends on it.

EXR-1-02.p65 2/28/01, 1:04 PM5

- for the terminals 5 and 6 is:

max = 0.5 Nm

advisable = 0.33 Nm

Fig. 7/A ESR/ESR-T TERMINAL BLOCK

Table 2

ESR-T Fuse

Model Manuf. model

Ferraz 6600.CP.URGB.14.51/20

12 - 240 Bussmann FWP.20A.14F

Ferraz 6600.CP.URGB.14.51/32

18 - 240 Bussmann FWP.30A.14F

9) For connect the devices to the power line, use

appropriate sized wires with 75 °C (167 °F)

minimum temperature rating. The following table

shows the recommended sizes:

Nominal fwires AWG

current (mm2)

12 A 2.5 14

18 A 4 12

25 A 6 10

40 A 10 8

60 A 16 6

80 A 25 (*) 4

(*) without wire terminal

10) The torque for tightening the terminals 1, 2

and earth of ESR-T and ESR is:

- for ESR-T and ESR 25

max = 0.8 Nm

advisable = 0.7 Nm

- for ESR 40, 60 and 80

max = 2 Nm

advisable = 1.5 Nm

EXR-1-02.p65 2/28/01, 1:04 PM6

11)The torque for tightening the terminals 1, 3, 5,

7 and earth of the ETR is:

max = 2 Nm

advisable = 1.5 Nm

- for the terminals A1 and A2 is:

max = 0.5 Nm

advisable = 0.33 Nm

Fig. 7/B ETR TERMINAL BLOCK

EXR-1-02.p65 2/28/01, 1:04 PM7

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente

ero electronic ESR Manuale utente

Manuali Sistema di controllo popolari di altre marche