ESAB Origo Mig 320 Manuale utente

Valid for serial no. 626-xxx-xxxx, 121-xxx-xxxx0463 274 001 GB 20120822

Origo™

Mig 320

Instruction manual

- 2 -

- 3 -

TOCe

Rights reserved to alter specifications without notice.

1 SAFETY 4...........................................................

2 INTRODUCTION 6...................................................

2.1 Equipment 6................................................................

3 TECHNICAL DATA 7.................................................

4 INSTALLATION 7....................................................

4.1 Location 7..................................................................

4.2 Assembly of components 8...................................................

4.3 Assembly of stabilizer 9......................................................

4.4 Electrical installation 9.......................................................

4.5 Mains power supply 10........................................................

5 OPERATION 11.......................................................

5.1 Connection and control devices 11.............................................

5.2 Overheating protection 11.....................................................

5.3 Inductance connection 12.....................................................

6 MAINTENANCE 12....................................................

6.1 Inspection and cleaning 12....................................................

7 FAULT TRACING 13..................................................

8 ORDERING OF SPARE PARTS 13......................................

DIAGRAM 14............................................................

ORDER NUMBER 18.....................................................

ACCESSORIES 19.......................................................

- 4 -

ba51e

1 SAFETY

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be ob

served in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equip

ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in

jury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding and cutting

2. The operator must ensure that:

Sno unauthorised person is stationed within the working area of the equipment when it is

started up.

Sno-one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame-proof

clothing, safety gloves.

SDo not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

WARNING

Do not use the power source for thawing frozen pipes.

- 5 -

ba51e

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and

cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill

SInstall and earth the unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

CAUTION

Read and understand the instruction manual before

installing or operating.

CAUTION

This product is solely intended for arc welding.

- 6 -

ba51e

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical and/or

electronic equipment that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain

information on approved collection stations.

For further information contact the nearest ESAB dealer.

ESAB can provide you with all necessary welding protection and accessories.

2 INTRODUCTION

The Mig 320 is a step switched power source designed for MIG/MAG−welding

together with wire feed units Feed 302 and Feed 304.

The power units are fan−cooled and equipped with thermal overload protection.

The machine is fitted with an instrument that displays current and voltage. It

incorporates a hold function and can be calibrated.

The power source comes in different variants, see page 18.

ESAB's accessories for the product can be found on page 19.

2.1 Equipment

The power source is supplied with:

SReturn cable, 3m, with return clamp

SShelf for gas cylinder

SGuide pin for wire feed unit

SInstruction manual

- 7 -

ba51e

3 TECHNICAL DATA

Mig 320

Voltage 230/400-415/500V 3∼50 Hz 230/440-460 3∼60Hz

Permissible load

at100 % duty cycle 195 A/24 V

at 60 % duty cycle 250 A/27 V

at 30 % duty cycle 320 A/30 V

Setting range (DC) 40A/16V-320A/30V

Open circuit voltage 16-40 V

Open circuit power 200 W

Efficiency at max current 75%

Power factor at max current 0.94

Control voltage 42 V, 50/60 Hz

Dimensions LxWxH 840 x 425 x 830

Weight 111 kg

Operating temperature -10 to +40°C

Transportation temperature -20 to +55°C

Enclosure class IP 23

Application classification

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 40°C.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

The installation must be carried out by a professional.

CAUTION

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user's responsibility to take adequate precautions.

4.1 Location

Position the welding power source in such way that its cooling air inlets and outlets

are not obstructed.

- 8 -

ba51e

4.2 Assembly of components

WARNING

During transport, the rear wheels of the power source are in their forward position.

Before use, place the wheels in their rear position.

- 9 -

ba51e

4.3 Assembly of stabilizer

Assemble the stabilizer if a counter balance is to be installed on machine. The stabilizer

is an accessory. The order number can be found on page 19.

Attention! Use of a counter balance without stabilizer may cause the machine to tip

over.

4.4 Electrical installation

- 10 -

ba51e

4.5 Mains power supply

Check that the unit is connected to the correct mains power

supply voltage, and that it is protected by the correct fuse size. A

protective earth connection must be made, in accordance with

regulations.

Rating plate with supply connection data

Recommended fuse sizes and minimum cable areas

Mig 320 3∼ 50 Hz 3∼ 50/60 Hz 3∼ 50 Hz 3∼ 60 Hz 3∼ 60 Hz

Voltage V 230 400/415 500 230 440/460

Current A

at100% duty cycle 16 9 7 16 8

at 60% duty cycle 23 14 10 23 12

at 30% duty cycle 35 20 16 34 18

Cable area mm24 x 4 4 x 2,5 4 x 2,5 4 x 4 4 x 2,5

Fuse, slow A 20 16 16 20 16

NB: The mains cable areas and fuse sizes as shown above are in accordance with Swedish

regulations. They may not be applicable in other countries: make sure that the cable area and fuse

sizes comply with the relevant national regulations.

Altri manuali per Origo Mig 320

Indice

Altri manuali ESAB Sistema di saldatura

ESAB

ESAB EMP 255ic Manuale utente

ESAB

ESAB Caddy Tig 1500i VRD Manuale utente

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud Manuale utente

ESAB

ESAB Aristo RoboFeed 3004w Manuale utente

ESAB

ESAB fabricator 141i Manuale utente

ESAB

ESAB Miggytrac B501 Manuale utente

ESAB

ESAB ESABMig C240 Manuale utente

ESAB

ESAB Buddy Feed 402 Manuale utente

ESAB

ESAB LHF 400 Manuale utente

ESAB

ESAB Rustler EM 201C Manuale utente

ESAB

ESAB EMP 215ic Manuale utente

ESAB

ESAB ET180i Manuale utente

ESAB

ESAB TIG 300i Manuale utente

ESAB

ESAB ES 180i Manuale utente

ESAB

ESAB Aristo Mig C3000i Manuale utente

ESAB

ESAB Heliarc SR-9 Guida

ESAB

ESAB AristoFeed 30- 4 Manuale utente

ESAB

ESAB MultiMaster 160 Manuale utente

ESAB

ESAB Powercut 650 Manuale utente

ESAB

ESAB Aristo Mig U4000i Manuale utente

ESAB

ESAB Migmaster 280 Pro Manuale utente

ESAB

ESAB Aristo Mig 5000i Manuale utente

ESAB

ESAB LAF 1251 Manuale utente

ESAB

ESAB ESABMig C420 Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente