EtherPower SUN-2242 Manuale utente

Benefits and Technical Information.

SUN-2242 is an Ethernet I/O controller with build-in web server. It has 2 digital inputs, 2

analog inputs, 2 relay outputs and 1-Wire input for up to 5 temperature & humidity

sensors.

SUN-2242 can be controlled and monitored over any TCP/IP network and Internet by web

browser or any specialized monitoring software by SNMP v1 and v2 protocol.

Benefits

Easy and fast configuration – full configuration can be performed through the Web

using a web browser

Control and configuration over SNMP

IP security – access is protected by name and password

Removable terminal connectors

2 dry contact inputs for monitor discrete detectors - door sensor, motion sensor, smoke

detector and etc. (volt free)

2 analog inputs

2 relays with NO contacts; ON/OFF or Pulse modes

1-Wire input for up to 5 Temperature & humidity sensors

HTTP API commands

XML (over HTTP)

SNTP synchronization protocol

Firmware update over IP

Alarm alert – SNMP trap and E-mail

SMTP with TLS Encryption

TLS 1.0, TLS 1.1 and TLS 1.2 support

E-mails to up 2 recipients like alarm alert

Dynamic DNS with support of DynDNS and No-IP services

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 2

Technical information

Power requirements

Input Voltage: 12VDC / 0.5 A (adapter)

Power Connector: Jack Ø5.5 x 2.0 / 10mm

Ethernet Interface

Connector: 8-pin RJ45

Magnetic Isolation Protection: 1.5 kV (built-in)

Number of ports: 1

Speed: 10/100 Mbps, Auto MDIX

Protocols

HTTP, DHCP, SNMP v1 and v2, SNTP, SMTP, SMTP TLS, XML

Operating conditions

Operating temperature: -20 to +70 °C

Operating Relative Humidity: 5 to 85% (non-condensing)

Digital inputs

Number: 2

Type: Dry contact

Isolation: Non isolated

Dry Contact Level: Logic “0”: Short to GND

Logic “1”: Open

Analog inputs

Number: 2

Type: Single ended

Input range: 0 to 60 VDC

Isolation: Non isolated

Resolution: 10-bit

Relay outputs

Number: 2

Contact type: Form A ( N.O. contact)

Max. switched current: 3A

Max. switched voltage: 30VDC

Insulation Resistance: 1000 mega-ohms 500 VDC at 20°C, 50% RH

Mechanical Life Expectancy: 5 000 000 operations

Electrical Life Expectancy: 120 000 operations

1-Wire interface

RJ11 for connecting 5x temperature & humidity sensors

Physical Characteristics

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 3

Housing: Aluminum enclosure / wall mount

Weight: 170 g

Dimensions: 112 x 82 x 40 [mm]

Warranty – 2 years

Device Connection

Connect the SUN-2242 to 10/100 Mb/s network. Use a classic TP patch cable for

connection to switch, router or to PC.

If the Ethernet connection is OK, the ACT and LINK indicator should light up and then ACT

indicator blink according to network data transfer.

Restoring defaults factory configuration

Press and hold the Reset button located on the back of the box, connect power, and hold

the button pressed for 10 seconds or more.

Default network parameters configuration:

IP address: 192.168.2.2

Network mask: 255.255.255.0

Default gateway: 192.168.2.1

IP configuration via DHCP: Disabled

User name: admin

Password: admin

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 4

Installation Guidelines

SUN-2242 controller must be installed by qualified personnel.

Controller must not be installed directly outdoors.

SUN-2242 must not be used for medical, life saving purposes, or for any purpose where its

failure could cause serious injury or the loss of life.

This unit must not be used in any way where it's function or failure could cause significant

loss or property damage.

The first step is to establish communication between computer and SUN-2242 controller.

This can be done by assigning a temporary IP address to the computer.

For computers with Windows OS assigning of IP address is made in “Local area connection

properties” or “Wireless Network Connection Properties”.

IP Address of the computer should be at the same network.

Into the web browser you should type http://192.168.2.2. If network settings are correct the

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 5

Web Pages

Login Page - access to the SUN-2242 is protected by name and password

Status Page - Monitoring parameters

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 6

Status page has 4 sections – “Digital inputs”, “Analog inputs”, “Outputs” and

“Sensors”.

Digital Inputs section can be used for monitoring sensors in “dry contact”(volt

free) mode - motion PIR sensors, Water Leak sensors, Water level sensors,

Door/window sensors, Smoke detectors.

One side of the sensor is connected to IN1 or IN2 terminal and the other is

connected to GND terminal.

Please note that Digital inputs are not galvanic isolated!

Analog Inputs section can be used for monitoring directly batteries, power

supplies, solar panels and any analog sensor with voltage up to 60V DC.

Please note that Analog inputs are not galvanic isolated!

Outputs section can be used to open/close garage door and control motors,

pumps, valves, lights …

For loads greater than 3A/30V DC an external relay should be used.

Sensors section can be used for control 5x1-Wire sensors for temperature and

humidity.

Maximum cable length when is used UTP cable is 50m.

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 7

Network Settings page – configuration of network parameters

Device name – up to 15 characters.

MAC address – hardware address of the device. It is unique and cannot be changed.

IP address – The SUN-2242 IP address configuration can be either static or set

through DHCP.

Enable DHCP - allows device automatically obtain a valid IP address from Gateway

Gateway – default gateway IP address

Subnet mask – local network mask

Primary DNS – needs to be set properly for correct operation. Domain Name Service

associates host names with IP addresses. Without a correctly configured DNS

server, the following functions will not work:

- Time synchronization (SNTP), used in e-mails and SNMP traps

- E- mailing (SMTP)

HTTP Port – The TCP port used for HTTP communications with SUN-2242. A default

setting for this port is 80. Value of HTTP port can be changed from 80 to 65500. It is

recommended that the port be left unchanged unless the user has an understanding

of TCP/IP and ports

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 8

System Settings

System name – used in the XML to easy identify of the device

System location – used in the XML to easy identify of the device

NTP server – host name of the NTP server used to synchronize time of the controller

Time zone – offset of time zone with respect to that of the NTP Server.

Interval – Automatic synchronization interval. This option allows the user to specify

how often the time on the SUN-2242 will be synchronized with the NTP server

Uptime - time since SUN-2242 was last powered.

Temperature Units - Specifies the unit of temperature (C – Celsius / centigrade, F –

Fahrenheit)

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 9

Account Settings - One user account with username and password can be configured

for HTTP access.

Sensor Settings

This page is used to configure temperature and humidity sensors.

Up to 5 x 1-Wire sensors can be connected to the SUN-2242.

Every 1-Wire sensor comes with a unique ID. After a sensor is connected must to find it

by click on the button "Find sensors".of Status web page.

S U N - 2 2 4 2 U s e r M a n u a l v 1 . 1 P a g e 10

Indice

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente