Extech Instruments 382095 Manuale utente
User Manual
Power and Harmonics Analyzer
Model 382095
382095 V4.1 7/06
2
EN 61010-2-032
CATIII600V
PollutionDegree2
Definition of Symbols:
Caution: Refer to Accompanyi ng D ocuments
Caution: Risk of Electric Shock
Double Insulati on
Over-voltage category III (CAT III): equipment in fixed installations.
WARNING: If the power analyzer is used in a manner not specified by the
manufacturer, the protection provided by the clamp meter may be impaired.
Please read the following instructions before use
1. Do not operate this instrument in wet or d usty environm ents.
2. Do not operate this instrument in the presence of combustible or explosive gas
3. Do not touc h e xposed meta l parts or unused terminals.
4. Consider the use of rub ber gl oves i n operatio n.
5. Do not operate in excess of AC 500V (P hase to Neutral), or AC 600V (Phase to Phase)
6. Do not operate this instrument if it appears to be malfunctioni ng
382095 V4.1 7/06
3
Table of Contents
FEATURES 5
PANEL DESCRIPTI ON 6
OPERATING INSTRUCTIONS 11
Power Quality of a 3 Phase 4 Wire (3P4W) System 11
Power Quality of a 3 Phase 3 Wire (3P3W) System 12
Power Quality of a Single Phase (1P2W) System 13
Power Quality of a 1 Phase 3 Wire (1P3W) System 14
Measurement of a S ystem with CT or VT 15
Harmonic Analysis of Voltage or Cu rrent 16
Display the Phase Angle of Harmonics 17
Measurement of Maximum Deman d 18
Waveform of Voltage and Current 18
Waveform of Voltage Only 19
Graphic Phase Diagram 19
Phase Sequence of a 3 Phase System 21
Balance and Unbalance 3 Phase (3P3W, 3P4W) Power Sou rce S ystem 21
Balance and Unbalance 3 Phase (3P3W or 3P4W) Load System 22
Transient Capture (Dips, S wells, Outage) 23
Down Load Transient Data 25
Data Logging of Power Data (3P4W, 3P3W, 1P2W, 1P3W) 25
Down Load Po wer Da ta 25
Data Logging of Harmonics 25
Down Load Harmonics Data 26
HARDCOPY of SCREEN 27
READ the SAVED SCREE N 28
SET THE CT AND VT RATIO 29
SET THE TIME INTERVAL FOR MAXIMUM DEMAND 30
SET THE SAMPLING TIME FOR DATA LOGGING 31
SET THE CALENDER CLOCK 32
PROTOCOL OF RS-232C IN TERFACE 33
SPECIFICATIONS 33
BATTERY REPLACEMENT 41
MAINTENANCE & CLEANIN G 41
Nomenclature 42
382095 V4.1 7/06
4
Support line (781) 890-7440
Product specifications subject to change without notice
For the latest version of this User ’s Guide, Software updates, and other
up-to-the-minute product information, visit our website: www.extech.com
Extech Instruments Corporation, 285 Bea r Hill Rd., Waltham, MA 02451
Warranty
EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and
workmanship for one year from date of shipment (a six month limited warranty applies to sensors and
cables). If it should become necessary to return the instrument for service during or beyond the warranty
period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our
website www.extech.com for contact information. A Return Authorization (RA) number must be issued
before any product is returned to Extech. The sender is responsible for shipping charges, freight, insurance
and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from
action of the user such as misuse, improper wiring, operation outside of specification, improper
maintenance or repair, or unauthorized modification. Extech specifically disclaims any implied warranties or
merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or
consequential damages. Extech's total liability is limited to repair or replacement of the product. The
warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied.
Calibration and Repair Services
Extech offers repair and calibration services for the products we sell. Extech also provides NIST
certification for most products. Call the Custome r Service Department for information on calibration
services available for this produc t. E xtech recomme nds that annual calibrations be performed to verify
meter performance and accuracy.
Copyright ©2006 Extech Instruments Corporation
All rights reserved including the right of reproduction in whole or in part in any form.
382095 V4.1 7/06
5
FEATURES
■ Analysis for 3P4W, 3P3W, 1P2W, 1P3W
■ True RMS value (V
123
and I
123
)
■ Active Power (W, KW, MW, GW)
■ Apparent and Reactive Power (KVA, KVAR)
■ Power Factor (P F), Phase Angle (Φ)
■ Energy (WH, KWH, KVARH, PFH)
■ Current measurement f rom 0.1 mA to 1000A, ca pable of anal yzing IT standby power consumption
to the maximum demand of a factory
■ Display of 35 Parameters in One Screen (3P4W)
■ Programmable CT (1 to 600 ) and PT (1 to 3000) Ratios
■ Display of Overlapped Voltage and Current Waveform
■ Maximum Demand (MD KW, MW, KVA, MVA) with Programmable Period
■ Harmonic Analysis (V
123
and I
123
) to the 99
th
Order
■ Display of 50 Harmonics in one Screen with Waveform
■ Display of Waveform with Peak Values (1024 Samples / Pe riod)
■ Analysis of Total Harm onic Distortion (THD-F)
■ Graphic Phase Diagram with 3 Phase System Parameters
■ Capture 28 Transient Events (Time + Cycles) with Programmable Threshold (%)
■ DIP, SWELL, and OUTAGE are included in transient events.
■ 3 Phase Voltage or Current Unbalanced Ratio (VUR, IUR)
■ 3 Phase Voltage or Current Unbalanced Factor (d0%, d2%)
■ Calculated Unbalanced Current through Neutral Line (In)
■ 512K Memory with Pro grammable Interval (Sampling time from 2 to 6000 seconds, data logging
time from 4.7 hours to 1180 days for 3P4W system)
■ Output of Waveform, Po wer Parameters and Harmonics on Command
■ Large Dot Matrix LCD Display with Backlight
■ Optical Isolated RS-232C Interface
382095 V4.1 7/06
6
PANEL DESCRIPTION
382095 V4.1 7/06
7
Panel Description
1. Input Terminal for Neutral Line (Voltage )
2. Voltage Input Terminals for Each Phase (V1 , V2, V3)
3. External DC Input (The AC adapto r must be 600V isolated)
4. Current Input Terminals for Each Phase (I 1, I2, I3)
5. LCD Display
6. Indication of locations where SEC., CT, VT, an d SETUP are displayed in LCD.
7. Buttons
8. RS-232C Window
9. Stand Holder
10. Stand
11. Battery Cover
12. Battery Compartment
Press this button to e xit transient detection mode. Also used to exit the SETUP menu
Press this button to pe rform t ransient detection
Press this button to hold the data displayed in LCD, press again to continue operation.
Press this button to begin th e measurement of harmonics in ma gnitude.
Press this button to select V1, I1, V2, I2, V3, o r I3 for harmonics anal ysis
382095 V4.1 7/06
8
Press this button for the voltage or current input range
Press to enter the Main Menu (also used t o navigate menu items).
Press this button to increment value by one. Hold the button for t wo seconds or
more to speed u p the increment.
Press this button to decre ment value by one.
In harmonic analysis mode, use these buttons to move the cursor left or right.
Press this button to start data logging. Press it again to stop data logging. The
sampling interval is displayed in the LCD via the SEC indicator.
In the power mode, press this button to display the phase. In th e harmo nic
analysis mode, press this button to display phase angle instead of magnitude.
Press this button to tu rn the back light on. Press it again to turn the back light off.
Press this button to begin me asuring power.
Press this button to displa y the waveforms for voltage and current.
Press this button to displa y the waveform for voltage only
In the power mode, press this button to select the appropriate s ystem (3P4W,
3P3W, 1P2W or 1P3W). In the waveform mode, press to select (V1, I1), (V2, I2),
or (V3, I3).
Press this button to tu rn the power on or off.
382095 V4.1 7/06
9
Current Probe (100A)
1. Jaw Assembly
2. Trigger
3. Range Selector
4. 6 pin mini DIN connector
NOTE: To choose the 100A current probe, press the SETUP button to select CLAMP. When the
CLAMP is reverse video, press the ▲or ▼button to select 100.
Current Probe (1000A)
1. Jaw Assembly
2. Trigger
3. Range Selector
4. 6 pin mini DIN connector
NOTE: To select the1000A current probe, press the SETUP button to select CLAMP. When the
CLAMP is reverse video, press the ▲or ▼button to select 1000.
(HARMON)
(POWER)
(HARMON)
60A
100A
100A
10A
1A
100A
1A
10A
10A
100A
1000A
382095 V4.1 7/06
10
Flexible Current Probe (3000A)
NOTE: The flexible current probe has a maximum input of 3000A however the maximum input
current of the 382095 Power and Ha rmonics Analyzer is 1000A.
1. Control Box
2. Output Range Select S witch
3. Flexible Loop
4. Coupling Assembly
NOTE: To select the 3000A flexible current pro be, press the SETUP button to select CLAMP. When
the CLAMP is reverse video, press the ▲or ▼button to select 3000.
Indice
Altri manuali Extech Instruments Strumento di misura
Extech Instruments
Extech Instruments EX820 Manuale utente
Extech Instruments
Extech Instruments HD450 Manuale utente
Extech Instruments
Extech Instruments Oyster Series Manuale utente
Extech Instruments
Extech Instruments HD750-NIST Manuale utente
Extech Instruments
Extech Instruments HDV7C-A4-60-1 Manuale utente
Extech Instruments
Extech Instruments RH520 Manuale utente
Extech Instruments
Extech Instruments HT200 Manuale utente
Extech Instruments
Extech Instruments 407445 Manuale utente
Extech Instruments
Extech Instruments EC170 Manuale utente
Extech Instruments
Extech Instruments PQ3350 Manuale utente
Extech Instruments
Extech Instruments PH210 Manuale utente
Extech Instruments
Extech Instruments RH390 Manuale utente
Extech Instruments
Extech Instruments BR250 Manuale utente
Extech Instruments
Extech Instruments 401027 Manuale utente
Extech Instruments
Extech Instruments SDL720 Manuale utente
Extech Instruments
Extech Instruments EX622 Manuale utente
Extech Instruments
Extech Instruments CO52 Manuale utente
Extech Instruments
Extech Instruments AN200 Manuale utente
Extech Instruments
Extech Instruments 34135-A Manuale utente
Extech Instruments
Extech Instruments CLT600 Manuale utente
