Extech Instruments Prc20 Manuale utente

USER GUIDE

Thermocouple Calibrator

Model PRC20

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

2PRC20-EU-EN-V1.2 1/13

Introduction

Thank you for selecting the Extech Model PRC20. This device is shipped fully tested and calibrated

and, with proper use, will provide years of reliable service. Please visit the Extech Instruments

website (www.extech.com) to check for the latest version of this User Guide. Extech Instruments is

an ISO-9001 certified company.

Safety

International Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages

may be present

Double insulation

Safety Notes

Turn the unit OFF when the device is not in use.

Remove the batteries if the device is to be stored for longer than 60 days.

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types. Always install new batteries of the same type.

Cautions

Improper use of this meter can cause damage, shock, injury or death. Read and understand

this user manual before operating the meter.

Inspect the condition of the thermocouples and the meter itself for any damage before

operating the meter. Repair or replace any damage before use.

If the equipment is used in a manner not specified by the manufacturer, the protection provided

by the equipment may be impaired.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

3PRC20-EU-EN-V1.2 1/13

Meter Description

1. AC adaptor input jack

2. Display

3. Power ON/OFF

4. Source output adjustment arrow buttons

5. Set and exit the adjustment mode button

6. Unit button (thermocouple type, °F or °C)

7. I/O button

8. MEM (memory STEP button)

9. Backlight/ZERO button

10. Thermocouple mini-connector

Display Layout

1. SOURCE mode icon

2. ZERO function status icon

3. Thermocouple type

4. MEASURE mode icon

5. Auto Power OFF active icon

6. Battery status icon

7. Measure mode value

8. Measure mode units icon

9. Datalogger memory location

10. Source mode value

11. Source mode units icon

12. Cold Junction Compensation (CJC) circuit status (ON or OFF)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

4PRC20-EU-EN-V1.2 1/13

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

5PRC20-EU-EN-V1.2 1/13

Keypad Descriptions and Operation

POWER BUTTON and AUTO POWER OFF FEATURE

1. Use the POWER button to turn the unit ON or OFF. When the unit is powered up, a short

self-test will ensue after which the display will stabilize.

2. When the battery symbol flashes on the display, replace the battery as soon as possible.

Low battery power may cause inaccurate readings and erratic meter operation.

3. This instrument is equipped with Auto Power OFF which turns the meter off after 10 minutes

of inactivity. To override this feature; press and hold the POWER button until the display

icon “ATP” turns off.

UNIT BUTTON

Momentarily press the UNIT button to select °F or °C units.

TYPE BUTTON

Press and Hold the TYPE/UNIT button for 1 second to change the thermocouple type (J, K, T, E, C,

R, S, N or mV).

I/O BUTTON

Momentarily press the I/O button to select either SOURCE (output) or MEASURE (input).

CJC ON/OFF

Simultaneously press the IO and MEM buttons to turn the CJC (cold junction compensation) on or

off. The CJC icon will indicate the status.

Note: CJC should normally be ON.

(Backlight) BUTTON

Momentarily press the Backlight button to turn the backlight on or off.

ZERO ( ) BUTTON

In the MEASURE or SOURCE mode, Press and Hold the ZERO ( ) button for 1 second to zero

the meter.

OFFSET ADJUSTMENT

The offset adjustment can be used to correct any known linearity errors with the thermocouple.

1. Select the measure mode and a thermocouple type (J/K/T/E/C/R/S/N).

2. Press and Hold the SET button for 1 second to enter the offset adjust mode.

3. Press the ▲or ▼button to change the offset value.

4. Press and Hold the SET button for 1 second to zero the offset value.

5. Momentarily press the SET button to save the change and exit the function.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

6PRC20-EU-EN-V1.2 1/13

►◄▼and ▲BUTTONS

The arrow buttons are used to set the output value in the SOURCE mode.

1. Select the SOURCE mode

2. Press the ►or ◄button select a digit for adjustment. The blinking underline curser

identifies the digit selected.

3. Press the ▼or ▲button to adjust the value of the digit. Press and Hold the ▼or ▲button to

rapidly adjust the value.

SET BUTTON

The SET button is used to manually step through the 5 stored output values.

1. Select the SOURCE mode

2. Momentarily press the SET button and the value stored in memory location 01 will be

sourced. “MEM.01” appears in the display.

3. Each press of the SET button will step through the 5 memory locations.

4. The arrow buttons can be used to adjust the value in each memory location.

STEP/MEM BUTTON

The STEP/MEM button is used to automatically step through the 5 stored output values. The meter

can be set for a single cycle of the stored values or a continuous cycle.

1. Select the SOURCE mode

2. Press and Hold the STEP/MEM button. ”STEPSS” (single cycle) and “STEPSC” (continuous

cycle) will alternately appear in the display. Release the button when the desired mode is

displayed.

3. In single cycle mode the meter will source the current or voltage displayed in MEM01 for 5

seconds. The meter will then advance to MEM02 for 5 seconds. This will continue through

MEM05 and then step down through the memory locations. The cycle will end when MEM01

has been reached.

4. In the continuous mode the cycle will continue until manually stopped.

5. Momentarily press the MEM button to stop the cycle. “END” will briefly appear in the display.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

7PRC20-EU-EN-V1.2 1/13

STORING VALUES INTO MEMORY

There are 5 memory locations for each thermocouple type and for mV. The default values stored in

the these locations are:

Memory

Location

Type

J, K, C, R, S, N

Type

M1 0.0oC

(32.0oF)

0.0oC

(32.0oF)

0.0oC

(32.0oF)

0mV

M2 100.0oC

(212.0oF)

100.0oC

(212.0oF)

100.0oC

(212.0oF)

10.00mV

M3 500.0oC

(932.0oF)

200.0oC

(392.0oF)

200.0oC

(392.0oF)

25.00mV

M4 750.0oC

(1382.0oF)

300.0oC

(572.0oF),

500.0oC

(932.0oF)

40.00mV

M5 1000.0oC

(1832.0oF)

400.0oC

(752.0oF)

750.0oC

(1382.0oF)

50.00mV

To change the values in memory:

1. Select the SOURCE mode

2. Press the SET button to select the memory location to be changed.

3. Press the arrow buttons to adjust to the new value

4. Momentarily press the MEM button to store the value. The memory location icon will blink

while the value is being stored..

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

8PRC20-EU-EN-V1.2 1/13

Modes of Operation

MEASURE (Input) Mode of Operation

1. Turn the meter ON.

2. “MEASURE” will appear in the display.

3. Momentarily press the UNIT button to select °F or °C.

4. Press and Hold the UNIT button for 1 second to change the thermocouple type (or mV).

5. Connect the thermocouple to the meter.

6. Read the measurement on the display.

Note: See the keypad description section to turn CJC on/off.

SOURCE (Output) Mode of Operation

In this mode, the unit can source the equivalent mV value for the temperature and the

thermocouple type selected. The values can be output either manually or stepped from memory

as described earlier.

1. Turn the meter ON

2. MEASURE” will appear in the display.

3. Momentarily press the UNIT button to select °F or °C.

4. Press and Hold the UNIT button for 1 second to change the thermocouple type (or mV).

5. Press the “I/O” button to select SOURCE.

6. Connect the Calibration Cable from the meter to the device to be calibrated.

7. Use the

arrow buttons to set the desired output value in the lower display. The upper

display indicates the actual temperature or voltage value being sourced. If the upper display

does not match the set value, check the batteries or the connections to the device being

calibrated.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

9PRC20-EU-EN-V1.2 1/13

Tilt Stand / Hanger

The rear stand is provides two methods for convenience in viewing.

1. Pull the bottom portion of the stand out to place the unit on a flat surface for viewing.

2. Pull the bottom and top portions of the stand out, and then rotate the stand to allow the unit

to be hung.

Battery Replacement

When the battery icon appears on the display, the six AA batteries must be replaced.

The battery compartment is located on the rear of the meter.

1. Open the tilt stand, loosen the captive Philips head screw and remove the battery cover.

2. Remove and replace the batteries, observing polarity.

3. Replace and secure the battery cover.

All EU users are legally bound by the Battery Ordinance to return all used batteries to

community collection points or wherever batteries / accumulators are sold.

Disposal in household trash or refuse is prohibited.

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Battery Safety Reminders

Please dispose of batteries responsibly; always observe local, state, and federal regulations

with regard to battery disposal.

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types or old and new batteries. Always install new batteries of the same

type.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

10 PRC20-EU-EN-V1.2 1/13

Specifications

General Specifications

Display Dot matrix LCD

Cold junction compensation 0.02°F per °F (0.03°C per °C)

Thermocouple Standard and Scale NIST 175, ITS-90

Meter Power 6 AA batteries or AC adaptor

Auto Power OFF Meter automatically powers off after 10 minutes of inactivity

Operating Temperature 5ºC to 40ºC (41ºF to 104ºF)

Storage Temperature -20ºC to 60ºC (- 4ºF to 140ºF)

Operating Humidity Max 80% up to 87ºF (31ºC) decreasing linearly to 50% at

104ºF (40ºC)

Storage Humidity <80%

Operating Altitude 2000 meters (7000ft) maximum

Dimensions 159 x 80 x 44 mm (6.3 x 3.2 x 1.7")

Weight 225g (8 oz.) without batteries

Range Specifications

Source and Measure Ranges Resolution Accuracy (% of reading)

Type J -58 to 1832°F (-50 to 1000°C)

Type K -58 to 2498°F (-50 to 1370°C)

Type T -184 to 752°F (-120 to 400°C)

Type E -58 to 1382°F (-50 to 750°C)

Type C 32 to 3182°F (0 to 1750°C)

Type R 32 to 3182°F (0 to 1750°C)

Type S 32 to 3182°F (0 to 1750°C)

Type N -58 to 2372°F (-50 to 1300°C)

0.1° (measure)

1° (source)

± (0.05% + 1°C /1.8°F)

mV Measure: -10mV to 60mV

Source: -5mV to 55mV 0.01mV ± (0.01% + 1digit)

www.extech.com

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extech Instruments Apparecchiature di prova

Extech Instruments

Extech Instruments MG325 Manuale utente

Extech Instruments

Extech Instruments ET60 Manuale utente

Extech Instruments

Extech Instruments 382252 Manuale utente

Extech Instruments

Extech Instruments 480403 Manuale utente

Extech Instruments

Extech Instruments SL120 Manuale utente

Extech Instruments

Extech Instruments CB10 Manuale utente

Extech Instruments

Extech Instruments ET15 Manuale utente

Extech Instruments

Extech Instruments MS420 Manuale utente

Extech Instruments

Extech Instruments ET25 Manuale utente

Extech Instruments

Extech Instruments ET10 Manuale utente

Extech Instruments

Extech Instruments CT70 Manuale utente

Extech Instruments

Extech Instruments ExStik PH150-C Manuale utente

Extech Instruments

Extech Instruments ET26B Manuale utente

Extech Instruments

Extech Instruments ET28B Manuale utente

Extech Instruments

Extech Instruments TK30 Manuale utente

Extech Instruments

Extech Instruments PRT200 Manuale utente

Extech Instruments

Extech Instruments 380375 Manuale utente

Extech Instruments

Extech Instruments 422123 Manuale utente

Extech Instruments

Extech Instruments 382356 Manuale utente

Extech Instruments

Extech Instruments MG320 Manuale utente

Extech Instruments

Extech Instruments TK36 Manuale utente

Extech Instruments

Extech Instruments HDV540 Manuale utente

Extech Instruments

Extech Instruments 7630 Manuale utente

Extech Instruments

Extech Instruments 407744 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Extech Instruments prc20 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche