Fasep V548.G4.U Manuale utente
www.fasep.it
User’s MANUAL
V548.G4
.U
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
For any information, please contact: www.fasep.it
e-mail: [email protected]
FASEP 2000 srl
Via Faentina 96 - Ronta
50032 Borgo San Lorenzo (Fi) Italy
Tel. #39 055 8403126
Fax #39 055 2691906 1
VIDEOTRONIC V548.G4.U
USER’S MANUAL
Fig. 1 V548.G4.A
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
2
WARNING
.This document contains information which is the property of FASEP 2000 rl and all rights are reserved. This manual shall not be
photocopied or reproduced in any way without the prior written consent of FASEP 2000 srl.
.FASEP 2000 srl reserves the right to revise products firmware, software or documentation without obligation to notify any person
or organization. The information contained in this document is subject to change without warning.
.Prior of the installation of the unit described in this manual, user should read this manual carefully to be instructed properly on
installation, use and maintenance of the unit.
.Failing to read this manual and operate accordingly may cause damage to the user or the unit.
.FASEP 2000 srl shall not be responsible for inconvenience, breakdown, accidents due to uncomplete knowledge of this manual
or uncomplete application of raccomendations described in this manual.
.FASP2000srlshallnotberesponsibleforinconvenience, breakdown, accidentsduetounauthorizedmodifications of the unit, use
ofnon-original or unauthorizedaccessories(see Accessories listingin this manual for alist oforiginal accessories available forthis
model).
.FASEP2000 srl shall not beresponsible for any inconvenience,breakdown, accidents caused directlyor indirectlyby not
qualified service. Service to any parts by not qualified persons will void warranty and will void any right of the owner of
the unit.
SYMBOLS AND CONVENTIONS
To speed the retrieval of main information and make easy to understand the instructions, this manual uses the following typing
conventions:
<NAME OF THE PUSH BUTTON> Used to indicate name of push-buttons on the control panel.
DISPLAY Used to indicate text or number visible on the displays on the control panel.
ADVICES Contain useful advices or solutions, evidence d with respect to the rest of the text.
NOTE Notes contain important information, evidenced to the rest of the text.
WARNING Warning messages appears corresponding to procedures that, if not properly observed,
may lead to loose of data or cause damage to the unit.
!CAUTION Caution messages appears corresponding to procedures that, if not properly observed,
may cause injuries to the user.
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
3
ORIGINAL INSTRUCTIONS
TABLE OF CONTENTS
WARNING .......................................................................................... 2
SYMBOLSANDCONVENTIONS ........................................................................ 2
1 PRESENTATION ............................................................................. 4
1.0 Intended Use ........................................................................ 4
1.1 Definitions .......................................................................... 4
2 INSTALLATION .............................................................................. 5
2.1 Movingtheunit....................................................................... 5
2.2 Assemblingtheunit ................................................................... 5
2.3 Installation .......................................................................... 5
2.4 ElectricalHookup..................................................................... 5
2.5 Power.............................................................................. 5
3 USEOFCONTROLPANEL..................................................................... 6
3.1 Meaning of the icons on the screen ....................................................... 6
4 CALIBRATIONOFWHEELBALANCER(USER) .................................................... 9
4.1 How to calibrate the wheel balancer (USER) ................................................ 9
4.2 How to control the calibration of wheel balancer and position weight (USER) ..................... 10
5 CalibrationALU-SE .......................................................................... 11
6 CalibrationSONAR .......................................................................... 12
7 MEASUREMENTANDCORRECTIONOFUNBALANCE............................................. 13
7.1 Placing the wheel rim on the wheel balancer ............................................... 13
7.2 Input of Rim Dimensions (Sonar system version) .. . . . ................................. 13
7.3 Input of Rim Dimensions (ALU-SE) ...................................................... 14
7.4 Detecting and correcting umbalance ..................................................... 14
7.5 How to apply the weight using ALU-SE applicator ........................................... 15
7.6 HowtouseSPLITProgram ............................................................ 15
8 SPECIAL FUNCTIONS ....................................................................... 16
8.1 Language selection .................................................................. 16
8.2 Setup ............................................................................. 16
APPENDIX ......................................................................................... 17
A: Technicaldata ...................................................................... 17
B: Environmental Data, Safety Features and Requirements ..................................... 18
C: Errors and Malfunctions recognized by the Computer ........................................ 19
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
4
1 PRESENTATION
1.0 Intended Use
This unit is designed to measure and correct static and dynamic unbalance of vehicle wheel, the dimension and weight
of which are within the working range of the machine (see “Technical Data”appendix for reference)
This unit is meant for a professional use. Operator shall be properly trained before use. Training Course is not included
in the price of the unit and must be purchased separately.
This unit is designed for indoor use only (see “Environmental Data”appendix for reference).
!CAUTION: This unit is designed to spin vehicle wheels only, within the range of dimensions and weight
approved (see “Technical Data”appendix for reference). Special adaptors suit this purpose. Do not
attempt to use the machine to spin anything else. Unproper locking may cause the part being
spinned to be ejected, causing damage to the unit itself, the operator or anything in the in the
neighboorhood.
1.1 Definitions
1. Monitor
2. Weights and tools trays
3. Side flange-holders
4. Foot pedal
5. Wheel guard
6. 3D Sonar input (optional)
7. Quick lock + HD shaft
8. ALU-S
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
5
2 INSTALLATION
2.1 Moving the unit
WARNING When the unit has to be moved: never lift balancer by motor shaft or
by neighborhood of it.
2.2 Assembling the unit
For ease of transportation, the wheel balancer might be disassembled into units. If
necessary, assembling instruction are provided within each package..
2.3 Installation
The wheel balancer must be installed on a firm and level ground.
NOTE:the machine must be secured to the floor. Using four holes in
the base and anchor bolts provided
2.4 Electrical Hookup
!CAUTION: Failure to follow these instructions can results in
damage to unit or create an electrical hazard and will
void warranty..
2.4.1 Electrical hookup is to be provided by a qualified electrician.
2.4.2 A fusible wall-mounted switchbox is required at the installation site. This
switchshouldprovide on-offcontrolandoverloadprotection foryourwheel
balancer only. The switchbox should be fused with time-delay fuse(s) in
accordance with the power rating specified on your wheel balancer.
2.4.3 Electrical connection of the machine should be by plug connectors.
2.4.4 The balancer must be effectively connectedto ground. Theelectric cord is
regularly provided with a ground terminal.
2.4.5 Make sure that Power Rate Specifications for your wheel balancer (refer to nameplate on the wheel balancer) comply
with those provided by the external power source.
!CAUTION Afterelectricalhookuphasbeenperformedunitisreadytooperate. Alwaysobservepertinentsafety
precautions when operating the unit (see Appendix tables for an overview of relevant Safety
requirement).
2.5 Power
Plug the wheel balancer into a 220V socket. To switch on the wheel
balancer press the red button (power) untill it light up. To swicth off the
wheel balancer press the red button (power) untill it light off.
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
6
3 USE OF CONTROL PANEL
3.1 Meaning of the icons on the screen
Select balancing mode
APS Function
Calibration
Delete last character in input
activation code
Change selection
Set default values
Fig. 6 Panel V555
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
7
Diagnostic
Key down
Position calibration
Go to previous page
Fine resolution
Access to Information center
Access to page measures
Laser calibration
Put in the rod laser in rest
position
Start laser
Extract fully rod laser
Manul input measures
Set Dynamic/Static
Mode moto
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
8
Key SET/OK
Double operator
Optimize
Restart software
Reset partial statistics
Reset variation in page Sensor
Save
Set measures
Go to setup menù
Skip current operation
Split function
Stop turning wheel
Key up
View menù and selection
(UP/DOWN)
Automatic flange calibration
Fig. 27
Fig. 28
Fig. 29
Fig. 30
Fig. 31
Fig. 32
Fig. 33
Fig. 34
Fig. 35
Fig. 36
Fig. 37
Fig. 38
Fig. 39
Fig. 40
Fig. 41
Fasep 2000 srl Rev. 1.8
Videotronic V548.G4.U: User’s Manual 11 March 2022
9
Fig. 42
Fig. 43
Fig. 44
Fig. 45
4 CALIBRATION OF WHEEL BALANCER (USER)
4.1 How to calibrate the wheel balancer (USER)
NOTE:the following symptoms indicate need for calibration::
a) check calibration program fails. b) constant low or high weight readings.
c) indicated point of unbalance constantly wrong d) more than 2 spins required to balance wheels
repeatedly.
Switch on the wheel balancer.
Select SET UP > CALIBRATION > SET/OK >
CALIBRATION > SET/OK.
Spin with no wheel on shaft (Fig. 42)
Close the wheel guard or press <START>.
At the end of the spin, put a wheel (Fig. 43)
and close the wheel guard or press <START>.
At the end of the spin, put the calibration
weight (Fig. 44) and close the wheel guard or
press <START>.
NOTA technical calibration is only available for qualified personnel
Indice
Altri manuali Fasep Smontagomme
Fasep
Fasep RASE.2234 Manuale utente
Fasep
Fasep RGU2671.G Manuale utente
Fasep
Fasep TOP AUTOMATIC 4.0 Istruzioni operative
Fasep
Fasep RASE.2247 Manuale utente
Fasep
Fasep RGU600E Manuale utente
Fasep
Fasep RASE.TOP.2248 Manuale utente
Fasep
Fasep BALATRON 331.G3 Manuale utente
Fasep
Fasep RAE.2108 Manuale utente
Fasep
Fasep RGU-566 Istruzioni operative
Fasep
Fasep RGU300.ECO Manuale utente
