Favero ASSIOMA UNO Manuale utente

1. User Manual 1EN

Manuale d’uso 17 IT

Technische Informationen 33 DE

Art. 772-01 ASSIOMA UNO cycle power meter

Art. 772-02 ASSIOMA DUO cycle power meter

0259-0902A _Rev10

FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

ENGLISH -USER MANUAL

Contents

1. Versions

Assioma UNO left pedal with power sensor,

right pedal without power sensor

Art.

772-01

Assioma DUO Left and right pedals with power sensor Art.

772-02

1. Versions 1

2. Package content 2

3. Product description 2

4. Warnings 3

5. Quick start 3

6. Switching on Assioma 3

7. Activating Assioma 3

8. Fixing the pedals to the crank-arms 4

9. Cleat xing, shoe position check and cleat release force adjustment 5

10. Bike computer conguration 7

11. Manual zero offset 8

12. Using Assioma for the rst time on road or rollers 9

13. Battery charge 9

14. Transforming Assioma UNO into Assioma DUO 11

15. Removing the pedals 11

16. Reinstalling the pedals (on another bicycle) 11

17. Compatible bike computers 11

18. LEDs behavior 12

19. Inspection and maintenance 12

20. Spare parts 12

21. Product troubleshooting 13

22. Copyright 14

23. Warranty 14

24. Technical features 14

25. Exploded view of the components 16

2FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

2. Package content

• Assioma pair of pedals with sensor (1 sensor for Assioma UNO, 2 sensors for Assioma DUO).

• 1 battery charger with EU, US, UK, AU plug adaptors ( IEC Types C, A, G ,I ).

• 2 m USB/micro USB cable (1 cable for Assioma UNO,2 cables for Assioma DUO).

• Magnetic charging connector (1 connector for Assioma UNO,2 connectors for Assioma DUO).

• 2 red cleats (6° oat), 1 8 mm hexagonal wrench, 4 washers.

• User manual, Safety instructions, Warranty information.

3. Product description

Assioma is a pedal for racing bicycles with a quick clip system, provided with power

sensor to measure the force applied to the pedal during pedal stroke.

This pedal includes the function of cadence meter and can calculate the power of a

single leg in real time, sending it to the bike computer.

It is provided with a 50 hour rechargeable battery and is designed to guarantee many

years of use. Therefore, there are no openings with gaskets for the replacement of the

battery.

Assioma is fully sealed (IP67) thanks to its case without openings and all its internal

components are immersed in a special lling resin.

For radio communication, Assioma is compatible with the ANT+ standard and

Bluetooth v4.0 standard, or later version. The use of Bluetooth v4.0 in

smartphones started in 2011 - 2012.

4 LEDs, one every 90°

Left pedal (L) or right pedal (R) indication

Connector for battery charging

Sensor

FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

2. Package content

• Assioma pair of pedals with sensor (1 sensor for Assioma UNO, 2 sensors for Assioma DUO).

• 1 battery charger with EU, US, UK, AU plug adaptors ( IEC Types C, A, G ,I ).

• 2 m USB/micro USB cable (1 cable for Assioma UNO,2 cables for Assioma DUO).

• Magnetic charging connector (1 connector for Assioma UNO,2 connectors for Assioma DUO).

• 2 red cleats (6° oat), 1 8 mm hexagonal wrench, 4 washers.

• User manual, Safety instructions, Warranty information.

3. Product description

Assioma is a pedal for racing bicycles with a quick clip system, provided with power

sensor to measure the force applied to the pedal during pedal stroke.

This pedal includes the function of cadence meter and can calculate the power of a

single leg in real time, sending it to the bike computer.

It is provided with a 50 hour rechargeable battery and is designed to guarantee many

years of use. Therefore, there are no openings with gaskets for the replacement of the

battery.

Assioma is fully sealed (IP67) thanks to its case without openings and all its internal

components are immersed in a special lling resin.

For radio communication, Assioma is compatible with the ANT+ standard and

Bluetooth v4.0 standard, or later version. The use of Bluetooth v4.0 in

smartphones started in 2011 - 2012.

4 LEDs, one every 90°

Left pedal (L) or right pedal (R) indication

Connector for battery charging

Sensor

4. Warnings

Please carefully read this manual and the safety instructions before installing

the product. An incorrect installation may lead to accidents and possible

damage to things and/or injury to people.

If you have any doubts about your ability to install the product, we recommend

you to ask for the assistance of a specialized mechanic. An incorrect installation

may cause or result in irreparable damage to the product which shall not be

covered by the warranty. Before starting to ride, check that the force necessary

to release your shoe from the pedal is suitable.

Visit the YouTube channel: Favero Cycling to see the detailed video installation.

https://www.youtube.com/Favero_cycling

5. Quick start

1. Switching on Assioma (Chap. 6).

2. Activating Assioma (Chap. 7).

3. Fixing the pedals to the crank-arms (Chap. 8).

4. Cleat xing, shoe position check and cleat release force adjustment (Chap. 9).

5. Bike computer conguration (Chap. 10).

• Pairing Assioma to the bike computer (Chap. 10.1).

• Conguration of power elds (Chap. 10.2).

• Crank-arm length (Chap. 10.3).

6. Manual zero offset (Chap. 11).

7. Using Assioma for the rst time on road or rollers (Chap. 12).

6. Switching on Assioma

Assioma will automatically switch on by turning the pedals or starting to ride and will

automatically switch off after 5 minutes of inactivity.

When using for the rst time, Assioma can only be switched on by connecting it

to the battery charger with the supplied cable for a few seconds. If the LEDs do

not blink, charge the battery as indicated in Chap. 13.

For LED behavior read Chap. 18.

7. Activating Assioma

Assioma must be activated to measure the power and cadence. If it is not activated,

such measuring will not be performed.

The activation also determines the start of the warranty period, allows updating the

4FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

software and sending diagnostic reports to check the correct operation of the product.

Activation is obtained with the specic “Favero Assioma” app, available both for iOS

and Android. The app can be downloaded free of charge.

Make sure that your smartphone is compatible with the Bluetooth v4.0

standard or later versions, and that your internet connections is active.

Open the app and follow the instructions to perform the search, the connection to

your device and the activation.

For more information, read the FAQs on the website: cycling.favero.com.

8. Fixing the pedals to the crank-arms

8.1. Washer use

The washers supplied are only necessary in the following cases:

• The crank-arm producer requires the use of a washer.

• The crank-arm has a recessed seat and one or two washers must be used to ensure a

free space between sensor and crank-arm.

Pressing the sensor against the crank-arm when tightening the pedal may

damage it. This operation would invalidate the warranty. If necessary, use 1 or 2

washers to ensure a free space of at least 1 mm between the sensor and

crank-arm.

If a cadence sensor is tted near the pedal, remove it to avoid any contact with

the Assioma sensor.

≥ 1 mm

Crank-arm

with recessed seat

0 mm

FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

8.2. Tightening the pedals

Before tightening the pedals, apply a thin layer of grease to the pedal axle thread.

Tighten the pedal to the crank-arm using the supplied 8 mm hexagonal wrench at a

tightening torque of about 35-40 Nm (25-30 ft lb), a standard torque for the tightening

of many pedals. If the crank-arm producer species a different tightening torque,

apply it.

Pay attention to the rotation direction:

• Tighten the left pedal

counter-clockwise

(facing the pedal).

• Tighten the right pedal

clockwise

(facing the pedal).

9. Cleat xing, shoe position check and cleat release force adjustment

9.1. Cleat xing

Use only the supplied cleats (red cleats, oat 6°) or original LOOK Kéo cleats.

The use of non-original LOOK kéo compatible cleats may be unsuitable and any

damage to the product will not be covered by the warranty.

To x the cleats, use the supplied screws and washers.

Align the cleat in the preferred position and tighten the screws with a tightening force of

4÷6 Nm (3÷4.5 ft lb), as for most of the cleats on the market.

6FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

Black cleats are also available for separate purchase

(oat 0°), Art. 771-40.

9.2. Shoe position check

Thanks to its reduced dimensions, the sensor never comes into contact with the shoe

even when large size or at-soled footwear is worn.

Before starting to ride, check that the distance between the shoe and the sensor

is at least 2 mm. Do not use the product if the sensor is in contact with the shoe,

the shoe cover or the cleat, as it can be damaged and this would invalidate the

warranty.

If the distance between the sensor and the shoe is less than 2 mm, move the cleat to the

most appropriate position or insert spacer Art.771-45 between the cleat and the shoe sole.

Washers

Cleat

Tightening torque:

4÷6 Nm (3÷4.5 ft lb)

Fixing screws

Cleat

≥ 2 mm

Shoe

Assioma

FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

9.3. Cleat release force adjustment

Before starting to ride, try to release the shoe several times and make sure that

the release force is suitable.

10. Bike computer conguration

10.1. Pairing Assioma to the bike computer

The pairing procedure associates Assioma to the bike computer to start the radio

communication between the two devices.

Please read the bike computer manual to learn how it performs the search and

pairing of a power sensor. Make sure that Assioma is switched on before

proceeding (Chap. 6).

Each Assioma has a unique 5-digit ANT+ ID identication number (written on the

packaging). This number identies Assioma in the list of devices which can be

paired with the bike computer.

Bike computers with ANT+ technology need only to be paired with the left pedal.

The left pedal will transmit the data collected by the associated right pedal too.

Bike computers, or other devices, with Bluetooth technology and Cycling Power

Prole (CPP) need to be paired with both the left and the right pedal.

The name of the right-sided Assioma will be recognizable by the R ID identication

number (indicated outside the box).

The spring tension can be adjusted using the

screw shown in the picture. To increase the

tension turn clockwise;

to decrease the tension, turn counter-clockwise.

Use a 3 mm wrench (not supplied).

Increase

Decrease

Adjust the tension

of the spring depending

on your needs.

8FAVERO Electronics - 0259-0902 Assioma user manual _Rev10 - EN-IT-DE

ENGLISH

Important warnings to avoid communication problems during the pairing:

• Make sure that there are no other power meters switched on nearby

(10 meters).

• The bike computer must be within 2 m from Assioma.

10.2. Conguration of power elds

Once the pairing procedure has been completed (Chap. 10.1), it is possible to congure

the bike computer so that it displays the power data in the preferred way: please refer

to the bike computer manual.

It is recommended to at least set the following parameters: 3 second power, 30 second

power, cadence, 30 second average balance.

10.3. Crank-arm length

The crank-arm length affects power calculation: Assioma must know this length. An

incorrect value will lead to incorrect power values.

Please refer to the bike computer manual to learn how to set the crank-arm length.

Use the Favero Assioma app only if it is not possible to set the crank-arm length on the

bike computer.

Setting the crank-arm lenght via the Favero Assioma app is useless if the bike

computer already provides this setting.

11. Manual zero offset

Each Assioma sensor is factory calibrated to ensure its guaranteed precision under any

operating conditions, including ambient temperature variations, for which automatic

compensation from -10°C to +60°C is active. For this reason, the user does not have to

calibrate the device.

However, it is important to periodically perform a “manual zero offset” to eliminate

any measurement variations which may have occurred over time, due to mechanical

adjustments or impacts.

Perform a manual zero offset adjustment any time the pedals are reinstalled and, for

maximum precision, any time you use them.

The zero offset function is often indicated in bike computers with the term of

“calibration”.

Altri manuali per ASSIOMA UNO

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Favero Strumento di misura

Favero

Favero ASSIOMA UNO Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente