Fluke 3210-PR Manuale utente

3210-PR

Flex Current Probe

Instruction Sheet

Introduction

The Fluke 3210-PR Flex Current Probe (“the Probe”) are ac

current Probes utilizing the Rogowski principle. They can be used

with the Fluke 1750 to measure current from very low frequencies

up to 15 kHz. The flexible and lightweight measuring head allows

quick and easy installation in hard to reach areas and with large

conductors.

The Probes are designed for use with the Fluke 1750 Power Recorder.

Contacting Fluke

To contact Fluke, call:

1-888-993-5853 in USA

1-800-363-5853 in Canada

+31-402-675-200 in Europe

+81-3-3434-0181 in Japan

+65-738-5655 in Singapore

+1-425-446-5500 from anywhere in the world Or,

visit Fluke’s Web site at www.fluke.com

To register your product, visit register.fluke.com

PN 3039189

July 2007

Symbols

The table below lists the symbols used on the Probe and/or in

this instruction sheet.

Symbol

Description

Do not dispose of this product as unsorted municipal

waste. Go to Fluke’s website for recycling information.

Important Information. See manual.

Hazardous Voltage. Risk of electric shock.

Double insulation.

Do not apply to or remove from hazardous, live

conductors.

)

Conforms to relevant standards of the Canadian

Standards Association.

Complies with the relevant European standards.

;

Conforms to relevant Australian standards.

Safety Instructions

Please read this section carefully. It will familiarize you with the

most important safety instructions for handling the Probe. In this

instruction sheet, a Warning identifies conditions and actions

that pose hazard(s) to the user. A Caution identifies conditions

and actions that may damage the Probe or the test instruments.

WX Warning

The Probe may only be used and handled by

qualified personnel. To avoid personal injury, follow

these precautions:

•Do not apply to or remove from hazardous live

conductors without taking additional protective

measures.

•To avoid electric shock, de-energize circuit

during installation and removal of Probe; high

voltages and currents may be present in

adjacent circuits.

•Do not use the Probe if damaged. Always

connect to display device before it is installed

around the conductor.

•Use the Probe only as specified in the operating

instructions; otherwise the safety features may

not protect you.

•Adhere to local and national safety codes.

Individual protective equipment must be used to

prevent the shock and arc blast injury where

hazardous live conductors are exposed.

•Before each use, inspect the Probe. Look for

cracks or missing portions of the housing or

output cable insulation. Also look for loose or

weakened components.

•Use caution when working with voltages above

60 V dc, 30 V ac rms or 42 V ac peak. Such

voltages pose a shock hazard.

•Use of this equipment is designed to 600 V CAT

IV or 1000 V CAT III standards. 600 V CAT IV or

1000 V CAT III equipment is designed to protect

against the transients in the equipment in fixed

equipment installations, such as distribution

panels, feeders and short branch circuits, and

the lighting systems in large buildings.

•Do not use the Probe in wet environments or in

locations that hazardous gases exist.

Operating Instructions

1. Connect the Probe to the 1750 via the 1750 current

input jack.

2. De-energize the circuit and place the Probe around the

conductor under test.

3. Observe and take measurements as required. Positive

output indicates that the current flow is in the direction

shown by the arrow on the Probe.

Maintenance

Cleaning

Clean the Probe periodically by wiping it with a damp cloth and

detergent. Do not use abrasive cleaners or solvents. Do not

immerse the Probe in liquids.

Specifications

Electrical Characteristics

Output Sensitivity @ 60 Hz

(@ output of the integrator)

2 mV/A

Accuracy (@ 25 °C)

± 1 % of reading

Linearity

(10 % to 100 % of range)

± 0.2 % of reading

Temperature Coefficient

± 0.05 % of reading per °C

Position Sensitivity (with cable >

25 mm from the coupling)

± 2 % of reading

External Field (with cable >

200 mm from the head)

± 1 % of reading

Working Voltage

(see Safety Standards)

1000 V under CAT III conditions

and 600 V under CAT IV

conditions. (V ac rms or dc)

General Characteristics

Probe and Cable Material

Alcryn 2070NC, reinforced

insulation, UL94 V0, Color: RED

Couplings Material

Lati Latamid 6H-V0 Nylon

Probe Cable Length

24 in. (610 mm) 3210-PR

Probe Cable Diameter

0.49 in. (12.4 mm)

Transducer Bend Radius (min)

1.5 in. (38.1 mm)

Output Cable

2 core screened, double insulated,

3 meters long

Output Connector

LEMO 6 pin male connector

Operating Temperature Range

-4 to +194 °F (-20 to +90 °C)

Storage Temperature Range

-40 to 221 °F (-40 to +105 °C)

Operating Humidity

15 % to 85 % (non condensing)

Degree of protection

IP40

Safety Standards

EN/IEC 61010-1 2001

EN/IEC 61010-2-032:2002

Pollution Degree 2

Use of the Probe on uninsulated conductors is limited to 1000 V

under CAT III conditions and 600V under CAT IV conditions ac

rms or dc and frequencies below 1 kHz.

Please note that the safety rating for the output to ground is

limited to 30 V ac rms or dc by the connector specified.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship

for one year from the date of purchase. This warranty does not cover

fuses, disposable batteries, or damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other warranty on

Fluke’s behalf. To obtain service during the warranty period, contact your

nearest Fluke authorized service center to obtain return authorization

information, then send the product to that Service Center with a

description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an implied

warranty or of incidental or consequential damages, this limitation of

liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Indice

Altri manuali Fluke Strumento di misura

Fluke

Fluke CableAnalyzer DSP-4100 Manuale utente

Fluke

Fluke 773-II Manuale utente

Fluke

Fluke SureGrip 80PK-25 Manuale utente

Fluke

Fluke VR101S Manuale utente

Fluke

Fluke 360 Manuale di istruzioni

Fluke

Fluke 917X Series Guida rapida

Fluke

Fluke OptiView Manuale utente

Fluke

Fluke TS54 TDR Manuale utente

Fluke

Fluke MultiFiber Pro Manuale utente

Fluke

Fluke v3000 FC Manuale utente

Fluke

Fluke OC3port Plus Manuale utente

Fluke

Fluke 323 Manuale utente

Fluke

Fluke i6000s Flex Series Manuale utente

Fluke

Fluke 15B MAX Manuale utente

Fluke

Fluke SMFT1000/PRO Manuale utente

Fluke

Fluke VR1710 Manuale utente

Fluke

Fluke i400s Manuale per l'uso e la cura

Fluke

Fluke 1520 Manuale utente

Fluke

Fluke 3310-PR Manuale utente

Fluke

Fluke ProcessMeter 787 Manuale utente

Fluke

Fluke CableAnalyzer DSP-4000 Series Manuale utente

Fluke

Fluke LinkSprinter 100 Manuale utente

Fluke

Fluke CableAnalyzer DSX-602 Manuale utente

Fluke

Fluke 433 Guida alla configurazione

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente