Fluke 323 PLUS Manuale utente
December 2015
© 2015 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
323/324 PLUS
Clamp Meter
Users Manual
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for two
years from the date of purchase. This warranty does not cover fuses, disposable
batteries, or damage from accident, neglect, misuse, alteration, contamination, or
abnormal conditions of operation or handling. Resellers are not authorized to
extend any other warranty on Fluke’s behalf. To obtain service during the warranty
period, contact your nearest Fluke authorized service center to obtain return
authorization information, then send the product to that Service Center with a
description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH
AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED.
FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR
THEORY. Since some states or countries do not allow the exclusion or limitation of
an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
i
Table of Contents
Title Page
Introduction.................................................................................................................1
How to Contact Fluke .................................................................................................1
Safety Information ......................................................................................................2
Symbols......................................................................................................................7
How to Clean the Product ..........................................................................................9
Specifications .............................................................................................................10
The Meter ...................................................................................................................15
323/324 PLUS
Users Manual
ii
1
Introduction
The Fluke 323/324 PLUS Clamp Meter (the Product) measures ac and dc voltage, ac current,
resistance, and continuity. The 324 PLUS can also measure capacitance, contact
temperature, and dc current. Note that the 324 PLUS is shown in all of the illustrations. For
temperature measurement, you must use the included K-Type Thermocouple.
XWWarning
Read "Safety Information" before you use the Product.
How to Contact Fluke
To contact Fluke, call one of the following telephone numbers:
•Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)
•Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)
•Canada: 1-800-36-FLUKE (1-800-363-5853)
•Europe: +31 402-675-200
•Japan: +81-03-6714-3114
323/324 PLUS
Users Manual
2
•Singapore: +65-6799-5566
•Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit http://register.fluke.com.
To see, print, or download the latest manual supplement, visit
http://us.fluke.com/usen/support/manuals.
Safety Information
A Warning identifies conditions and procedures that are dangerous to the user. A Caution
identifies conditions and procedures that can cause damage to the Product or the equipment
under test.
Table 1 tells you about symbols used on the Product and in this manual.
Clamp Meter
Safety Information
3
XWWarning
To prevent possible electrical shock, fire, or personal injury:
•Use the Product only as specified, or the protection supplied by the
Product can be compromised.
•Use only correct measurement category (CAT), voltage, and amperage
rated probes, test leads, and adapters for the measurement.
•Do not touch voltages > 30 V ac rms, 42 V ac peak, or 60 V dc.
•Carefully read all instructions.
•Hold the Product behind the tactile barrier. See Clamp Meter, item .
•Do not exceed the Measurement Category (CAT) rating of the lowest
rated individual component of a Product, probe, or accessory.
•Do not measure current while the test leads are in the input jacks.
•Do not use the Product around explosive gas, vapor, or in damp or wet
environments.
•Limit operation to the specified measurement category, voltage, or
amperage ratings.
•Do not work alone.
323/324 PLUS
Users Manual
4
•Do not apply more than the rated voltage, between the terminals or
between each terminal and earth ground.
•Comply with local and national safety codes. Use personal protective
equipment (approved rubber gloves, face protection, and flame-
resistant clothes) to prevent shock and arc blast injury where
hazardous live conductors are exposed.
•Replace the batteries when the low battery indicator shows to prevent
incorrect measurements.
•The battery door must be closed and locked before you operate the
Product.
•Measure a known voltage first to make sure that the Product operates
correctly.
•Remove all probes, test leads, and accessories that are not necessary
for the measurement.
•Only use probes, test leads, and accessories that have the same
measurement category and voltage rating as the Product.
•Keep fingers behind the finger guards on the probes.
Clamp Meter
Safety Information
5
•Connect the common test lead before the live test lead and remove the
live test lead before the common test lead.
•Remove all probes, test leads, and accessories before the battery door
is opened.
•Do not use the Product if it is damaged.
•Disable the Product if it is damaged.
•Do not use the Product if it operates incorrectly.
•Do not use test leads if they are damaged. Examine the test leads for
damaged insulation, exposed metal. Check test lead continuity.
•Before each use, examine the Product. Look for cracks or missing
pieces of the clamp housing. Also look for loose or weakened
components. Carefully examine the insulation around the jaws. See
Clamp Meter, item .
•Examine the case before you use the Product. Look for cracks or
missing plastic. Carefully look at the insulation around the terminals.
•Read all safety Information before you use the Product.
323/324 PLUS
Users Manual
6
•Remove batteries to prevent battery leakage and damage to the Product
if it is not used for an extended period.
•Remove batteries to prevent battery leakage and damage to the Product
if is to be stored above its operating temperature.
•Do not use a current measurement as an indication that a circuit is safe
to touch. A voltage measurement is necessary to know if a circuit is
hazardous.
•Do not use in CAT III or CAT IV environments without the protective cap
(if included with the Product) installed on test probe. The protective cap
decreases the exposed probe metal to <4 mm. This decreases the
possibility of arc flash from short circuits.
WCaution
To avoid possible damage to the Product or to equipment under test, use a
thermocouple rated for the temperatures to be measured. The Product is
rated for -10.0 °C to +400.0 °C and 14 °F to 752 °F. The included type-K
thermocouple is rated to 260 °C.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Fluke Strumento di misura
Fluke
Fluke 9062 Manuale utente
Fluke
Fluke 3000A Flex 4 Manuale utente
Fluke
Fluke 771 Manuale utente
Fluke
Fluke CO-205 Manuale utente
Fluke
Fluke CableAnalyzer DSP-4100 Manuale utente
Fluke
Fluke 323 Manuale utente
Fluke
Fluke 772 Manuale utente
Fluke
Fluke 368 Manuale per l'uso e la cura
Fluke
Fluke 80K-4 Manuale utente
Fluke
Fluke 360 Manuale per l'uso e la cura
Fluke
Fluke 772 Manuale utente
Fluke
Fluke 5790B Manuale utente
Fluke
Fluke 985 Manuale utente
Fluke
Fluke 1735 Manuale utente
Fluke
Fluke ScopeMeter 190 II 190-104 Manuale utente
Fluke
Fluke Victoreen 190 Manuale utente
Fluke
Fluke 830 Manuale utente
Fluke
Fluke Datapaq Food Tracker Manuale utente
Fluke
Fluke 772 Manuale per l'uso e la cura
Fluke
Fluke 712B Manuale utente
