Fluke 106 Manuale utente

PN 4343876

June 2013

All product names are trademarks of their respective companies.

106 & 107

Digital Multimeters

Users Manual

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship for one

year from the date of purchase. This warranty does not cover fuses, disposable

batteries, or damage from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Resellers are not authorized to

extend any other warranty on Fluke’s behalf. To obtain service during the warranty

period, contact your nearest Fluke authorized service center to obtain return

authorization information, then send the product to that Service Center with a

description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH

AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED.

FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR

THEORY. Since some states or countries do not allow the exclusion or limitation of

an implied warranty or of incidental or consequential damages, this limitation of

liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Table of Contents

Title Page

Introduction.................................................................................................................1

Safety Information ......................................................................................................1

Safe Working Practices ..............................................................................................2

Instrument Overview...................................................................................................7

Terminals................................................................................................................7

Display....................................................................................................................8

Auto Power Off ........................................................................................................... 9

Auto Backlight Off.......................................................................................................9

Measurements..........................................................................................................10

Data Hold .............................................................................................................10

Measure AC and DC Voltage ...............................................................................10

Measure AC or DC Current ..................................................................................12

Measure Resistance.............................................................................................14

Test for Continuity ................................................................................................14

Test Diodes (107 Only) ........................................................................................16

106 & 107

Users Manual

Measure Capacitance...........................................................................................17

Measure Frequency and Duty Cycle (107 Only) ..................................................17

Maintenance ............................................................................................................. 18

General Maintenance ...........................................................................................19

Test the Fuse........................................................................................................20

Replace Batteries and the Fuse ...........................................................................21

Service and Parts .....................................................................................................22

General Specifications..............................................................................................23

Accuracy Specifications............................................................................................25

Introduction

The Fluke 106 and 107 Multimeters (the Product) are 6000 count instruments.

The Product is battery powered with a digital display.

Except where noted, the descriptions and instructions in this Users Manual apply to both the

106 and 107.

Unless otherwise identified, all illustrations show the 107.

Safety Information

The Fluke 106 and 107 comply with IEC 61010-1 CAT III 600 V overvoltage standard. See

Specifications.

A Warning identifies conditions and procedures that are dangerous to the user. A Caution

identifies conditions and procedures that could cause damage to the Product or the

equipment under test.

International electrical symbols used on the Product and in this manual are explained in Table 1.

106 & 107

Users Manual

Safe Working Practices

Review the safety information and comply with the safe working practices.

  Warning

To prevent possible electrical shock, fire, or personal injury:

• Carefully read all instructions.

• Read all safety information before you use the Product.

• Use the Product only as specified, or the protection supplied by the Product

can be compromised.

• Do not use the Product around explosive gas, vapor, or in damp or wet

environments.

• Do not use and disable the Product if it is damaged.

• Do not use the Product if it operates incorrectly.

• Examine the case before you use the Product. Look for cracks or missing

plastic. Carefully look at the insulation around the terminals.

Multimeters

Safe Working Practices

• Use only correct measurement category (CAT), voltage, and amperage rated

probes, test leads, and adapters for the measurement.

• Measure a known voltage first to make sure that the Product operates

correctly.

• Do not use test leads if they are damaged. Examine the test leads for

damaged insulation and measure a known voltage.

• Limit operation to the specified measurement category, voltage, or amperage

ratings.

• Do not apply more than the rated voltage, between the terminals or between

each terminal and earth ground.

• Do not use the HOLD function to measure unknown potentials. When HOLD

is turned on, the display does not change when a different potential is

measured.

• Do not touch voltages >30 V ac rms, 42 V ac peak, or 60 V dc.

• Do not use test leads if they are damaged. Examine the test leads for

damaged insulation and measure a known voltage.

106 & 107

Users Manual

• Keep fingers behind the finger guards on the probes.

• Remove all probes, test leads, and accessories before the battery door is

opened.

• Do not exceed the Measurement Category (CAT) rating of the lowest rated

individual component of a Product, probe, or accessory.

• Remove the input signals before you clean the Product.

• Use only specified replacement parts.

• Use only specified replacement fuses.

• Have an approved technician repair the Product.

• Remove the batteries if the Product is not used for an extended period of

time, or if stored in temperatures above 50 °C. If the batteries are not

removed, battery leakage can damage the Product.

• Replace the batteries when the low battery indicator shows to prevent

incorrect measurements.

For safe operation and maintenance of the product, repair the Product before

use if the batteries leak.

Multimeters

Safe Working Practices

Table 1. International Electrical Symbols



AC (Alternating Current)



Earth Ground



DC (Direct Current)



Fuse



AC or DC



Capacitance



Risk of Danger. Important

information. See Manual.



Diode



Battery CAT II

MEASUREMENT CATEGORY II is

applicable to test and measuring

circuits connected directly to utilization

points (socket outlets and similar

points) of the low voltage MAINS

installation.

CAT III

MEASUREMENT CATEGORY III

is applicable to test and

measuring circuits connected to

the distribution part of the

building’s low-voltage MAINS

installation.

CAT IV

MEASUREMENT CATEGORY IV is

applicable to test and measuring

circuits connected at the source of the

building’s low voltage MAINS

installation.

106 & 107

Users Manual



Conforms to relevant North

American Safety Standards.



Conforms to European Union

directives.



Conforms to relevant South

Korean EMC Standards.



Inspected and licensed by TÜV

Product Services.



This product complies with the WEEE Directive (2002/96/EC) marking requirements. The

affixed label indicates that you must not discard this electrical/electronic product in

domestic household waste. Product Category: With reference to the equipment types in

the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control

Instrumentation" product. Do not dispose of this product as unsorted municipal waste. Go

to Fluke’s website for recycling information.

Multimeters

Instrument Overview

Terminals

1 2 3

hhc01.eps

Item Description

1 Input terminal for ac and dc current measurements to 10 A and current frequency (107

only) measurements.

2 Common (return) terminal for all measurements.

3 Input terminal for voltage, resistance, continuity, diode (107 only), capacitance, and

frequency (107 only) measurements.

106 & 107

Users Manual

Display

1 2 3 4 5 6 7 8

1314

hhc02.eps

Item Description Item Description

1 High voltage 8 Hz – Frequency is selected

2 Display Hold is enabled 9 F – Farads for capacitance

3 Continuity selected 10 mV – millivolts

4 Diode test is selected 11 A, V – amps or volts

5 Duty Cycle is selected 12 DC, AC – dc or ac voltage or current

6 M, k – decimal prefix 13 Auto Range mode is enabled

7  – Ohms is selected 14 Battery is low and should be changed

Multimeters

Auto Power Off

The Product automatically powers off after 20 minutes of inactivity.

To restart the Product, turn the rotary switch back to the OFF position and then to a

necessary position.

To disable the Auto Power Off function, hold down the Shift key when turning on the Product,

until PoFF shows on the display.

Auto Backlight Off

The backlight automatically turns of after 2 minutes’ inactivity.

To disable the Auto Backlight Off function, hold down the  key when turning on the Product,

until LoFF shows on the display.

Note

To disable both the Auto Power Off function and the Auto Backlight Off function, you can

also hold down the Shift key and the  key at the same time, until both PoFF and LoFF

show on the display.

106 & 107

Users Manual

Measurements

Data Hold

Warning

To prevent possible electrical shock, fire or personal injury, do not use the HOLD

function to measure unknown potentials. When HOLD is turned on, the display

does not change when a different potential is measured.

To hold the present reading, push



. Push



again to resume normal operation.

Measure AC and DC Voltage

To measure AC and DC voltage:

1. Choose ac or dc by turning the rotary switch to or .

2. Connect the red test lead to the



terminal and the black test lead to the COM terminal.

3. Measure the voltage by touching the probes to the correct test points of the circuit.

4. Read the measured voltage on the display.

Multimeters

Measurements

Volts AC Volts DC Millivolts AC

hhc03.eps

Figure 1. Measure AC and DC Voltage

106 & 107

Users Manual

Measure AC or DC Current

 Warning

To prevent possible electrical shock, fire, or personal injury, remove circuit power

before you connect the Product in the circuit when you measure current. Connect

the Product in series with the circuit.

1. Turn the rotary switch to



2. Push the YELLOW button to toggle between ac or dc current measurement by.

3. Connect the red test lead to the A terminal based on the current to be measured and

connect the black test lead to the COM terminal.

4. Break the circuit path to be measured. Then connect the test leads across the break and

apply power.

5. Read the measured current on the display.

Multimeters

Measurements

hhc04.eps

Figure 2. Measure AC and DC Current

106 & 107

Users Manual

Measure Resistance

1. Turn the rotary switch to



(106 does not have the diode symbol). Make sure power

is disconnected from the circuit to be measured.

2. Connect the red test lead to the



terminal and the black test lead to the COM terminal.

3. Measure the resistance by touching the probes to the desired test points of the circuit.

4. Read the measured resistance on the display.

Test for Continuity

With the resistance mode selected, push the YELLOW button once to activate the continuity

beeper. If the resistance is <70 , the beeper will sound continuously, designating a short

circuit. If the Product reads , the circuit is open.

Multimeters

Measurements

< 70

hhc05.eps

Figure 3. Measure Resistance/Continuity

106 & 107

Users Manual

Test Diodes (107 Only)

1. Turn the rotary switch to



2. Push the YELLOW function button twice to activate Diode Test.

3. Connect the red test lead to the



terminal and the black test lead to the COM terminal.

4. Connect the red probe to the anode side and the black test lead to the cathode side of the

diode being tested.

5. Read the forward bias voltage value on the display.

6. If the polarity of the test leads is reversed with diode polarity, the display reading shows  .

This can be used to distinguish the anode and cathode sides of a diode.

Altri manuali per 106

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manuale utente