Fluke 175 Manuale utente

Models 175, 177, 179

True RMS Multimeters

Users Manual

October 2000 (English), Rev 1, 7/01

Lifetime Limited Warranty

Each Fluke 175, 177, and 179 DMM purchased after 1 January 2000 will be free from defects in material and workmanship for its lifetime.

This warranty does not cover fuses, disposable batteries and damage from neglect, misuse, contamination, alteration, accident or abnormal

conditions of operation or handling, including overvoltage failures caused by use outside the DMMs specified rating, or normal wear and tear

of mechanical components. This warranty covers the original purchaser only and is not transferable.

For ten years from the date of purchase, this warranty also covers the LCD. Thereafter, for the lifetime of the DMM, Fluke will replace the

LCD for a fee based on then current component acquisition costs.

To establish original ownership and prove date of purchase, please complete and return the registration card accompanying the product.

Fluke will, at its option, repair at no charge, replace, or refund the purchase price of a defective product purchased through a Fluke author-

ized sales outlet and at the applicable international price. Fluke reserves the right to charge for importation costs of repair/replacement parts

if product purchased in one country is sent for repair elsewhere.

If product is defective, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product

to that service center, with a description of the difficulty, postage and insurance prepaid (FOB Destination). Fluke assumes no risk for dam-

age in transit. Fluke will pay return transportation for product repaired or replaced in-warranty. Before making any non-warranty repair, Fluke

will estimate cost and obtain authorization, then invoice you for repair and return transportation.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE

EXPRESSED OR IMPLIED. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAM-

AGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT

AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON FLUKE’S BEHALF. Since some states do not allow the exclusion or limita-

tion of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you. If any provision of this

warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding will not affect the validity

or enforceability of any other provision.

Fluke Corporation Fluke Europe B.V.

P.O. Box 9090 P.O. Box 1186

Everett, WA 98206-9090 5602 BD Eindhoven

U.S.A. The Netherlands

Visit the Fluke website at: www.fluke.com.

11/99

Table of Contents

Title Page

Read Before Using the Meter: Warnings and Precautions .................................................... ii

Contacting Fluke................................................................................................................... 1

"Warning" and "Caution" Statements .................................................................................... 1

Unsafe Voltage ..................................................................................................................... 1

Test Lead Alert...................................................................................................................... 1

Battery Saver ("Sleep Mode") ............................................................................................... 2

Terminals.............................................................................................................................. 2

Rotary Switch Positions ........................................................................................................ 2

Display.................................................................................................................................. 3

MIN MAX AVG Recording Mode........................................................................................... 4

Display HOLD and AutoHOLD Modes................................................................................... 4

YELLOW Button.................................................................................................................... 4

Display Backlight (Model 177 and 179 Only)......................................................................... 4

Manual Ranging and Autoranging......................................................................................... 5

Power-Up Options................................................................................................................. 5

Making Basic Measurements................................................................................................ 6

Measuring AC and DC Voltage........................................................................................ 6

Measuring Resistance...................................................................................................... 6

Measuring Capacitance ................................................................................................... 6

Testing for Continuity....................................................................................................... 7

Measuring Temperature (Model 179 Only)....................................................................... 7

Testing Diodes................................................................................................................. 7

Measuring AC or DC Current........................................................................................... 8

Measuring Frequency ...................................................................................................... 8

Using the Bar Graph .............................................................................................................9

Cleaning................................................................................................................................9

Testing the Fuses.................................................................................................................. 9

Replacing the Battery and Fuses .......................................................................................... 10

Specifications........................................................................................................................ 10

Warning. Read before using the Meter:

To avoid possible electrical shock or personal injury, follow these gidelines:

⇒Use the Meter only as specified in this manual or the protection provided by the Meter might be impaired.

⇒Do not use the Meter or test leads if they appear damaged, or if the Meter is not operating properly. If in doubt, have the

Meter serviced.

⇒Always use the proper terminals, switch position, and range for measurements.

⇒Verify the Meter’s operation by measuring a known voltage.

⇒Do not apply more than the rated voltage, as marked on the Meter, between the terminals or between any terminal and earth

ground.

⇒Use caution with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. These voltages pose a shock hazard.

⇒Replace the battery as soon as the low battery indicator ( b) appears to avoid false readings that can lead to electric shock

and injury.

⇒Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or

capacitance.

⇒Do not use the Meter around explosive gas or vapor.

⇒When using the test leads, keep your fingers behind the finger guards.

⇒Remove test leads from the Meter before opening the Meter case or battery door.

Symbols

BAC (Alternating Current) IFuse

FDC (Direct Current) PConforms to European Union directives

BDC/AC Canadian Standards Association

JEarth ground TDouble insulated

WImportant Information; see manual Underwriters Laboratories, Inc.

Meter in accordance with IEC 61010-1. 54CJ

bBattery (Low battery when shown on display.)

;

N10140 Conforms to relevant Australian standards

Inspected and licensed by TÜV (Technischer Überwachungs Verein) Product Services

Models 175, 177 & 179

True RMS Multimeters

The Fluke Model 175, Model 177, and Model 179 are battery-

powered, true-RMS multimeters (hereafter "the Meter") with a

6000-count, 3 3/4-digit display and a bar graph. This manual

applies to all three models. All figures show the Model 179.

These meters meet CAT III and CAT IV IEC 61010 standards.

The IEC 61010 safety standard defines four overvoltage

categories (CAT I to IV) based on the magnitude of danger from

transient impulses. CAT III meters are designed to protect against

transients in fixed-equipment installations at the distribution level;

CAT IV meters are designed to protect against transients from the

primary supply level (overhead or underground utility service).

The Meter measures or tests the following:

♦AC / DC voltage & current ♦Diodes

♦Resistance ♦Continuity

♦Voltage & frequency ♦Capacitance

♦Temperature (Model 179 only)

Contacting Fluke

To contact Fluke, call:

1-888-993-5853 in USA and Canada

+31 402-678-200 in Europe

+81-3-3434-0181 in Japan

+65-738-5655 in Singapore

+1-425-446-5500 from anywhere in the world

Visit Fluke’s web site at: www.fluke.com.

"Warning" and "Caution" Statements

A "

Warning" identifies hazardous conditions and actions that

could cause bodily harm or death.

A "Caution" identifies conditions and actions that could damage

the Meter, the equipment under test, or cause permanent loss of

data.

Unsafe Voltage

To alert you to the presence of a potentially hazardous voltage,

when the Meter detects a voltage ≥30 V or a voltage overload

(OL), the Ysymbol is displayed.

Test Lead Alert

To remind you to check that the test leads are in the correct

terminals, LEAd is momentarily displayed when you move the

rotary switch to or from the mA or Aposition.

Warning

Attempting to make a measurement with a test lead in

an incorrect terminal might blow a fuse, damage the

Meter, and cause serious personal injury.

Models 175, 177 & 179

Users Manual

Battery Saver ("Sleep Mode")

The Meter enters the "Sleep mode" and blanks the display if the

Meter is on but is not used for 20 minutes. To disable the Sleep

mode, hold down the YELLOW button while turning the Meter on.

The Sleep mode is always disabled in the MIN MAX AVG mode

and the AutoHOLD mode.

Terminals

FUSED

AIK01F.EPS

Item Description

1 Input terminal for AC and DC milliamp measurements

to 400 mA (600 mA for 18 hrs) and frequency

measurements.

2 Input terminal for AC and DC current measurements to

10 A (20 A for up to 30 seconds) and frequency

measurements.

3 Input terminal for voltage, continuity, resistance, diode,

capacitance, frequency, and temperature (Model 179

only) measurements.

4 Common (return) terminal for all measurements.

Rotary Switch Positions

Switch

Position Measurement Function

Hz AC voltage from 0.1 mV to 1000 V.

Frequency from 2 Hz to 99.99 kHz.

Hz DC voltage 1 mV to 1000 V.

Frequency from 2 Hz to 99.99 kHz.

DC mV 0.1 mV to 600 mV dc.

Temperature −40 °C to +400 °C

−40 °F to +752 °F

Ohms from 0.1 Ωto 50 MΩ.

Farads from 1 nF to 9999 µF.

2-kHz beeper turns on at <25 Ωand turns off at

>250 Ω.

Diode test. Displays OL above ~2.4 V.

AC or DC mA from 0.01 mA to 600 mA.

Frequency of AC mA 2 Hz to 99.99 kHz.

AC or DC A from 0.01 A to 10 A (20 A for 30

seconds).

>10.00 display flashes.

>20 A, OL is displayed.

Frequency of AC A to 99.99 kHz.

Note: AC voltage and current AC-coupled, true RMS, up to 1 kHz.

Display

13 14 15

12 10

AIK02F.EPS

No. Symbol Meaning

1 SContinuity test.

Diode test.

3 KNegative readings.

4 YUnsafe voltage. Voltage ≥30 V, or

voltage overload (OL)

Display HOLD is enabled. Display

freezes present reading.

In MIN MAX AVG mode, MIN MAX

AVG recording is interrupted.

AutoHOLD is enabled. Display holds

present reading until it detects new

stable input. Then the Meter beeps

and displays new reading.

MAX , MIN,

AVG

MIN MAX AVG enabled.

Maximum, minimum, or average

reading.

No. Symbol Meaning

7 nµF, °F, °C

mVA, Mk

, kHz Measurement units.

8 DC, AC Direct current, alternating current.

9 b

Low battery. Battery voltage < 6 V

0.2 V.

10 610000mV All possible ranges.

11 Bar graph Analog display.

12 Auto Range

Manual Range

The Meter selects the range with

the best resolution.

The user selects the range.

13 ±Bar graph polarity.

14 0L The input out of range.

15 LEAd

Test lead alert. Displayed when

the rotary switch is moved to or

from the mA or Aposition.

Error Messages

diSC Displayed while the capacitor discharges. In

Capacitance function only.

EEPr Cannot read data from EEPROM. Turn power off,

then on. If message remains, service Meter.

EEPr

Err Invalid EEPROM data. Have Meter serviced.

CAL

Err Invalid calibration data. Calibrate Meter.

Models 175, 177 & 179

Users Manual

MIN MAX AVG Recording Mode

The MIN MAX AVG recording mode captures the minimum and

maximum input values, and calculates a running average of all

readings. When a new high or low is detected, the Meter beeps.

Note

For DC functions, accuracy is the specified accuracy of the

measurement function

12 counts for changes longer than

275 ms in duration.

For AC functions, accuracy is the specified accuracy of the

measurement function

40 counts for changes longer than

1.2 s in duration.

To use MIN MAX AVG recording:

⇒Make sure that the Meter is in the desired measurement

function and range. (Autoranging is disabled in the MIN MAX

AVG mode.)

⇒Press MIN MAX to activate MIN MAX AVG mode.

and MAX light, and the highest reading detected

since entering MIN MAX AVG is displayed.

⇒Press MIN MAX to step through the low (MIN), average

(AVG), and present readings.

⇒To pause MIN MAX AVG recording without erasing stored

values, press HOLD.

is displayed.

To resume MIN MAX AVG recording, press HOLD again.

turns off.

⇒To exit and erase stored readings, press MIN MAX for 1

second or turn the rotary switch.

Display HOLD and AutoHOLD Modes

Warning

To avoid electric shock, do not use the Display HOLD or

AutoHOLD mode to determine if a circuit is live.

Unstable or noisy readings will not be captured.

In the Display HOLD mode, the Meter holds the reading on the

display.

In the AutoHOLD mode, the Meter holds the reading on the

display until it detects a new stable reading. Then the Meter

beeps and displays the new reading.

⇒Press HOLD to activate Display HOLD.

lights.

⇒Press HOLD again to activate AutoHOLD.

lights.

⇒Press HOLD again to resume normal operation.

To resume normal operation at any time, press HOLD for 1

second or turn the rotary switch.

YELLOW Button

Press the YELLOW button to select alternate measurement

functions on a rotary switch setting, e.g., to select DC mA, DC A,

Hz, temperature (Model 179 only), capacitance, diode test.

Display Backlight (Model 177 and 179 Only)

Press

to toggle the backlight on and off. The backlight

automatically turns off after 2 minutes.

Manual Ranging and Autoranging

The Meter has both Manual range and Autorange modes.

⇒In the Autorange mode, the Meter selects the range with the

best resolution.

⇒In the Manual Range mode, you override Autorange and

select the range yourself.

When you turn the Meter on, it defaults to Autorange and Auto

Range is displayed.

1. To enter the Manual Range mode, press RANGE.

Manual Range is displayed.

2. In the Manual Range mode, press RANGE to increment the

range. After the highest range, the Meter wraps to the lowest

range.

Note

You cannot manually change the range in the MIN MAX

AVG, Display HOLD, or AutoHOLD modes.

If you press

RANGE

while in MIN MAX AVG, Display

HOLD, or AutoHOLD, the Meter beeps, indicating an

invalid operation, and the range does not change.

3. To exit Manual Range, press RANGE for 1 second or turn the

rotary switch.

The Meter returns to Autorange and Auto Range is displayed.

Power-Up Options

To select a Power-Up Option, hold down the button indicated

while turning the Meter from OFF to any switch position.

Power-Up Options are cancelled when the Meter is turned OFF.

Button Power-Up Options

AutoHOLD

Turns on all display segments.

Release HOLD to turn off display; the software

version number is displayed and the Meter

resumes normal operation.

MDisables beeper.

REnables "Smoothing" mode.

Dampens display fluctuations of rapidly changing

inputs by digital filtering.

(YELLOW)

Disables automatic power-down ("Sleep mode").

Sleep mode is also disabled while the Meter is in a

MIN MAX AVG Recording mode, or the AutoHOLD

mode.

SDisables automatic 2-minute backlight timeout.

(Model 177 and 179 Only)

Models 175, 177 & 179

Users Manual

Making Basic Measurements

The figures on the following pages show how to make basic

measurements.

When connecting the test leads to the circuit or device, connect

the common (COM) test lead before connecting the live lead;

when removing the test leads, remove the live lead before

removing the common test lead.

Warning

To avoid electric shock, injury, or damage to the Meter,

disconnect circuit power and discharge all high-voltage

capacitors before testing resistance, continuity, diodes,

or capacitance.

Measuring AC and DC Voltage

Volts AC Volts DC Millivolts DC

VVmV

RANGEHOLD

MINMAX

RANGEHOLD

MINMAX

RANGEHOLD

MINMAX

AIK03F.EPS

Measuring Resistance

RANGEHOLD

MINMAX

AIK04F.EPS

Measuring Capacitance

RANGEHOLD

MINMAX

AIK05F.EPS

Altri manuali per 175

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fluke Multimetro

Fluke

Fluke 113 Manuale di istruzioni

Fluke

Fluke 175 Manuale utente

Fluke

Fluke J 39200 Manuale utente

Fluke

Fluke 1550B Manuale utente

Fluke

Fluke 8024B Manuale utente

Fluke

Fluke 8600A Manuale utente

Fluke

Fluke LinkRunner Duo Manuale utente

Fluke

Fluke CNX 3000 Manuale per l'uso e la cura

Fluke

Fluke 8845A Manuale operativo e di manutenzione

Fluke

Fluke CNX C3001 Manuale utente

Fluke

Fluke 80 Series III Manuale utente

Fluke

Fluke 76 Manuale utente

Fluke

Fluke 117 Manuale utente

Fluke

Fluke a3002 FC Manuale per l'uso e la cura

Fluke

Fluke 789 Manuale utente

Fluke

Fluke 79 Manuale utente

Fluke

Fluke 287 Manuale utente

Fluke

Fluke 8060A Manuale utente

Fluke

Fluke 113 Manuale per l'uso e la cura

Fluke

Fluke 8845A Manuale per l'uso e la cura

Fluke

Fluke 12 Manuale utente

Fluke

Fluke CNX i3000 Manuale per l'uso e la cura

Fluke

Fluke 83 Manuale utente

Fluke

Fluke 27-II Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manuale utente