Fluke CableAnalyzer DSX-500 Manuale utente

PN 4329967 (English) May 2013, Rev. 4 6/2016

2013-2016 Fluke Corporation

All product names are trademarks of their respective companies.

*4329967*

DSX

CableAnalyzer™

Getting Started Guide

The DSX-5000 CableAnalyzer modules attach to Versiv™main

and remote units to make rugged, hand-held testers that let you

certify, troubleshoot, and document twisted pair network

cabling.

Accessing the Product Manuals

This guide provides basic information to help you get started

using the tester. For more detailed information, see the latest

versions of the Versiv Users Manual and the Versiv Technical

Reference Handbook provided on the Fluke Networks website.

Symbols

Warning or Caution: Risk of damage or destruction to

equipment or software. See explanations in the manuals.

Warning: Risk of fire, electric shock, or personal injury.

Do not connect this equipment to public communications

networks, such as telephone systems.

This product complies with the WEEE Directive marking

requirements. The affixed label indicates that you must not

discard this electrical/electronic product in domestic

household waste. Product Category: With reference to the

equipment types in the WEEE Directive Annex I, this product

is classed as category 9 "Monitoring and Control

Instrumentation" product. Do not dispose of this product as

unsorted municipal waste.

Conformite Europeene. Conforms to the requirements of the

European Union and the European Free Trade Association

(EFTA).

Conforms to relevant North American standards.

Conforms to relevant Australian standards.

www.calcert.com sales@calcert.com1.888.610.7664 0

Safety Information

Warning

To prevent possible fire, electric shock, or personal injury:



Read all safety information before you use the

Product.



Carefully read all instructions.



Do not connect the tester to telephony inputs,

systems, or equipment, including ISDN inputs.

Doing so is a misapplication of this product, which

could result in damage to the tester and create a

potential shock hazard to the user.



Do not open the case. You cannot repair or replace

parts in the case.



Do not modify the Product.



Use only replacement parts that are approved by

Fluke Networks.



Do not touch voltages > 30 V AC rms, 42 V AC peak,

or 60 V DC.



Do not use the Product around explosive gas, vapor,

or in damp or wet environments.



Use this Product indoors only.



Do not connect the Product to voltages that are

higher than the maximum voltage rating for the

Product.



For Products that have multiple connectors for

different types of tests on copper cabling,

disconnect unused test leads from the connectors

before you do a test.



Use the Product only as specified, or the protection

supplied by the Product can be compromised.

Conforms to relevant Russian standards.

KCC-REM-FKN-012001001: EMC approval for Korea

Class A Equipment (Industrial Broadcasting &

Communication Equipment)

This product meets requirements for industrial (Class A)

electromagnetic wave equipment and the seller or user

should take notice of it. This equipment is intended for use

in business environments and is not to be used in homes.

This key turns the Product on and off.

www.calcert.com sales@calcert.com1.888.610.7664 0



Do not use and disable the Product if it is damaged.



Do not use the Product if it operates incorrectly.



Batteries contain hazardous chemicals that can

cause burns or explode. If exposure to chemicals

occurs, clean with water and get medical aid.



Remove the batteries if the Product is not used for

an extended period of time, or if stored in

temperatures above 50 °C. If the batteries are not

removed, battery leakage can damage the Product.



Replace the rechargeable battery after 5 years of

moderate use or 2 years of heavy use. Moderate use

is defined as recharged twice a week. Heavy use is

defined as discharged to cutoff and recharged daily.



Disconnect the battery charger and move the

Product or battery to a cool, non-flammable

location if the rechargeable battery becomes hot

(>50 °C, >122 °F) during the charge period.The

battery door must be closed and locked before you

operate the Product.



Repair the Product before use if the battery leaks.



Recharge the batteries when the low battery

indicator shows to prevent incorrect measurements.



Turn off the Product and disconnect all test leads,

patch cords, and cables before you replace the

battery.



Do not disassemble or crush battery cells and

battery packs.



Do not put battery cells and battery packs near heat

or fire. Do not put in sunlight.



Do not operate the Product with covers removed or

the case open. Hazardous voltage exposure is

possible.



Remove the input signals before you clean the

Product.



Have an approved technician repair the Product.



Do not put metal objects into connectors.



For Products with rechargeable batteries, use only

AC adapters approved by Fluke Networks for use

with the Product to supply power to the Product

and charge the battery.

www.calcert.com sales@calcert.com1.888.610.7664 0

Caution

To prevent damage to the Product or cables under test

and to prevent data loss, read all safety information given

in all documentation supplied with the Product.

Connectors, Keys, and LEDs

HFO00EPS

Figure 1. Connectors, Keys, and LEDs



Connector for a link interface adapter.



RJ45 jack for communications between the main and remote

testers when you do alien crosstalk measurements.



LCD display with touchscreen.



: Starts a test. To start a test, you can also tap TEST on the

display.



Power key.



: Press to go to the home screen.



Connector for the ac adapter. The LED is red when the battery

charges, and green when the battery is fully charged. The LED

is yellow if the battery will not charge.



RJ45 connector: Lets you connect to a network for access to

Fluke Networks cloud services.



Micro-AB USB port: This USB port lets you connect the tester to

a PC so you can upload test results to the PC and install

software updates in the tester.



Type A USB port: This USB host port lets you save test results on

a USB flash drive, connect the FI-1000 video probe to the tester,

or connect a Wi-Fi adapter for access to Fluke Networks cloud

services.

www.calcert.com sales@calcert.com1.888.610.7664 0



Headset jack.



PASS LED comes on when a test passes.

TEST LED comes on during a test.

FAIL LED comes on when a test fails.

TALK LED comes on when the talk function is on (see ). To

adjust the volume, press or the button on the headset’s

microphone.

TONE LED flashes and the toner comes on when you press

and a main tester is not connected to the remote.

LOW BATTERY LED comes on when the battery is low.

Note

The LEDs also operate as a battery gauge when

you turn on the remote. See the Users Manual.



: Press to use the headset to speak to the person

at the other end of the link. Press again to adjust the volume.

To turn off the talk function, hold down .

How to Certify Twisted Pair Cabling

Power the Tester

Charge the battery if necessary. Connect the ac adapter to

ac power and to the adapter connector () shown in Figure

1. You can use the tester while the battery charges.

Select Settings

2-1

On the home screen, tap the test setup panel (see

Figure 2).

2-2

On the CHANGE TEST screen, tap a twisted pair test, then

tap EDIT.

2-3

On the TEST SETUP screen, tap the panels to change

settings.

2-4

To save the settings, tap SAVE on the TEST SETUP screen.

-continued-

www.calcert.com sales@calcert.com1.888.610.7664 0

HFO01.EPS

Figure 2. Panels on the Home Screen



To set up a project, tap the PROJECT panel.



To change settings for the test or select a different test, tap

the test setup panel.



To set up cable IDs and turn on Auto Save, tap the Next ID

panel.



To upload test results to LinkWare Live, tap SYNC.

Make Connections and Do a Test

3-1

Connect the testers to the link as shown in Figure 3 or 4.

3-2

Tap TEST on the main tester or press on the main

or remote tester.

www.calcert.com sales@calcert.com1.888.610.7664 0

GPU97.EPS

Figure 3. Permanent Link Connections

GPU96.EPS

Figure 4. Channel Connections

Patch

panel

Start permanent

link

End permanent

link

Horizontal cabling

Tester with

permanent link

adapter

Remote with

permanent link

adapter

Wall outlet

Optional

consolidation

point

Patch cord

from hub or

switch

Start channel End channel

Horizontal cabling

Tester with

channel adapter

Remote with

channel adapter

Wall outlet

Optional

consolidation

point

Hub or switch

Patch cord

from PC

www.calcert.com sales@calcert.com1.888.610.7664 0

Examine the Results

The tester shows multiple views of the test results (Figure 5):



WIRE MAP: Shows the connections between the ends of

the cable under test. The tester compares the connections

to the selected Outlet Configuration to get a PASS or FAIL

result.



PERFORMANCE: Shows the overall result for each test that

is required by the selected test limit. To see detailed results

for a test, tap the panel.



HFO02.EPS

Figure 5. Examples of Twisted Pair Results Screens

Save the Results

5-1

Tap SAVE if the test passed or FIX LATER if the test

failed.

5-2

If the Cable ID box shows the correct ID, tap SAVE.

To enter a cable ID, tap the Cable ID box on the SAVE RESULT

screen, use the keyboard to enter a name for the results, tap

DONE, then tap SAVE.

The tester saves the results in the DEFAULT project, unless you

selected a different project.

About Projects

You can set up a project to specify the settings and tests

necessary for a job, monitor the status of a job, and organize the

test results.

To start a new project, tap PROJECT on the home screen, tap

CHANGE PROJECT, then tap NEW PROJECT. See the Users Manual

or Technical Reference Handbook for more information.

www.calcert.com sales@calcert.com1.888.610.7664 0

About Fluke Networks Cloud Services

With a Fluke Networks web account and a wired or wireless

network connection, you can use the LinkWare™Live web

application to store and manage projects in the cloud.

About the AxTalk Analyzer Kit

The DSX-5000 kit includes the hardware and AxTalk Analyzer

software you need to do tests for alien crosstalk on twisted pair

cabling. Alien crosstalk is noise, or crosstalk, transmitted

between adjacent cables in a bundle or patch panel. Alien

crosstalk is a primary source of noise in cabling used for

10GBASE-T applications.

For instructions on how to do alien crosstalk tests, install the

AxTalk Analyzer software, which is available on the Fluke

Networks website, then see the online help in the software.

Registration

Registering your product with Fluke Networks gives you access

to valuable information on product updates, troubleshooting

tips, and other support services.

To register, use LinkWare PC software. Download LinkWare PC

from the Fluke Networks website.

Fluke Networks operates in more than 50 countries worldwide.

For more contact information, go to our website.

General Specifications

Battery Type Lithium-ion

Temperature Operating: 0 °C to +45 °C

Storage: -30 °C to +60 °C

Altitude Operating: 4,000 m (3,200 m with AC adapter)

Storage: 12,000 m

www.calcert.com sales@calcert.com1.888.610.7664 0

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Fluke Networks mainframe products will be free from defects in

material and workmanship for one year from the date of

purchase, unless stated otherwise herein. Parts, accessories,

product repairs and services are warranted for 90 days, unless

otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or

other peripherals are all considered parts or accessories. This

warranty does not cover damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation

or handling. Resellers are not authorized to extend any other

warranty on Fluke Networks’ behalf. To obtain service during

the warranty period, contact your nearest Fluke Networks

authorized service center to obtain return authorization

information, then send your defective product to that Service

Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSED OR IMPLIED. FLUKE NETWORKS IS NOT LIABLE

FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.

Since some states or countries do not allow the exclusion or

limitation of an implied warranty or of incidental or

consequential damages, this limitation of liability may not apply

to you.

4/15

www.calcert.com sales@calcert.com1.888.610.7664 0

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fluke Apparecchiature di prova

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente