Frequency Central Deep Thought Manuale

Frequency central

Build documentation for:

Deep thought

Boolean Logic module featuring code by Jetroid

Deep Thought is a Boolean logic module with two distinct sections. The upper section features

addressable Boolean logic, with any one of NOT A, NOT B, AND, NAND, OR, NOR, XOR and XNOR

being chosen either via knob or via CV input. The lower section features simultaneous outputs of

NOT A, NOT B, AND, NAND, OR, NOR, XOR and XNOR.

Key to PCB screen print:

n: This signifies NPN BC547 transistors. Note the correct pinout as shown by the half circles.

The PCB shows the correct orientation for BC547. Other similar transistor types can be used,

but please observe the correct pinout.

Please observe the correct polarity of the electrolytic capacitors.

Bill of Materials

1K x 15

4K7 x 13

10K x 6

91K x 2

100K x 6

240K x 2

All resistors ¼ watt

metal film.

100nF

10uF x 1

47uF x 2

Deep Thought PIC

TL072 x 2

BC547 x 4

78L05

3mm red LED x 13

8 pin IC socket x 2

14 pin IC socket x 1

Alpha 9mm B100K x 1

3.5mm socket x 13

Male header

(cut to size)

Female header

(cut to size)

Power header

(cut to size)

Knob x 1

Main PCB assembly

1. Solder all resistors

2. Solder all three IC sockets

3. Solder the 100nF capacitor

4. Solder all four transistors and 78L05 –watch the polarity!

5. Solder the power header.

6. Solder all electrolytic capacitors

7. Cut male headers to size and solder them into place. Make sure that they stick out of

the bottom of the PCB.

Pots ‘n’ sockets PCB

1. Place all sockets on the PCB, making sure the ground tabs line up with the PCB’s

ground pads –be careful here as there are four different orientations - then place

the panel over them. This will assure that the sockets are correctly positioned. Flip

the whole lot over and solder the sockets into place.

2. Use cut off resistor legs to connect the sockets’ ground tabs line up with the PCB’s

ground pads.

3. Solder the potentiometer in place

4. Cut female headers to size and solder them into place. Make sure that they stick out

of the bottom of the PCB.

5. Put all thirteen LEDs through their pads –be careful here as there are two different

orientations. Present the panel to the PCB, flip the whole lot over, make sure the

LEDs stick though the holes in the panel, solder in place.

There’s no calibration to do! But –make sure that you plug the main PCB into the pots ‘n’

sockets PCB the right way around!

RDH 09/06/18

http://www.frequencycentral.co.uk/

Altri manuali Frequency Central Unità di controllo

Frequency Central

Frequency Central State 700 Manuale

Frequency Central

Frequency Central Raging Bull 2.0 Manuale

Frequency Central

Frequency Central Seismograf Manuale

Frequency Central

Frequency Central MU Wave Runner LFO Manuale

Frequency Central

Frequency Central Dual XVCA Manuale

Frequency Central

Frequency Central Meth Amp Rev.2 Manuale

Frequency Central

Frequency Central Waverider Digital VCO Manuale

Frequency Central

Frequency Central MU System X Dual ADSR Manuale

Frequency Central

Frequency Central System X Filter Manuale

Frequency Central

Frequency Central System X Filter 2 Manuale

Frequency Central

Frequency Central Waverider VCDO MKii Manuale

Frequency Central

Frequency Central Continuum Phase Shifter Manuale

Frequency Central

Frequency Central MU System X Dual Amplifier Manuale

Frequency Central

Frequency Central System X Amplifier Manuale

Frequency Central

Frequency Central Bartos Flur Rev(2) Manuale

Frequency Central

Frequency Central XVCO Manuale

Frequency Central

Frequency Central Infinitely Maybe Manuale

Frequency Central

Frequency Central Pocket Calculator Rev(2) Manuale

Frequency Central

Frequency Central Looking glass Manuale utente

Frequency Central

Frequency Central Continuum Phaser ii Manuale

Frequency Central

Frequency Central Polygraf Manuale

Frequency Central

Frequency Central MU System X Lowpass Filter Manuale

Frequency Central

Frequency Central System X CV Mixer Manuale

Frequency Central

Frequency Central Raging Bull Manuale

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente