Front Runner Easy-Out Manuale utente

Easy-Out Awning

Brackets

RRAC029

ENG

30 min

IMPORTANT WARNING!

Thank you for purchasing the Easy-Out Awning Bracket.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD

RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT

RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND

DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO

INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY

FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

RRAC029_REV_C01

TOOLS NEEDED

1 3 X Mounting Bracket

2 15 X M6 x 16 Hex Bolt

3 15 X M6 x 12 x 1SS Flat Washer

4 15 X M6 Nyloc Nut

5 6 X M6 Nut Cap

6 6 X M8 x 20 Hex Bolt

7 15 X M8 x 16 x 1.6SS Flat Washer

8 15 X M8 Nyloc Nut

9 6 X M8 Nut Cap

10 6 X M8 x 25 Button Head Bolt

11 3 X M8 x 20 Button Head Bolt

IN THE BOX

FIGURE 1.1

5mm

6.5mm

13mm

10mm10mm

13mm

GET ORGANIZED1

SLIMLINE II RACK (Steps 2.1 - 2.3)

FIGURE 1.2

SLIMLINE RACK (Steps 3.1 - 3.3)

RRAC029_REV_C01

711

AWNING BRACKET INSTALLATION - SLIMLINE II RACK

Depending on the type of Awning Extrusion,

slide either three M6 x 16 Hex Bolt or three

M8 x 20 Hex Bolts (Items 2 or 6) into the top

extrusion slot and three into the bottom

extrusion slot.

Place the Mounting Brackets over the

Hex Bolts (two per bracket). Fit a ﬂat washer

and Nyloc Nut onto the bolts used

(Items 3, 4 or 7, 8). Space the Mounting

Brackets accordingly.

13MM

5MM

Position the Awning onto the Slimline II Rack

with the help of a friend. Secure the center

Mounting Bracket ﬁrst.

Fit the M8 x 16 x 1.6SS Flat washer and the

M8 Nyloc Nuts loosely onto the M8 x 25

Button Head Bolts (Items 7, 8, 10). Do the

same with both other Brackets. Make sure

the Awning is centered correctly.

Underneath the Mounting Brackets, you will

notice the center hole in the Bracket lines up

to the hole in the Side Proﬁle. Insert a

M8 x 20 Button Head Bolt and

M8 x 16 x 1.6SS Flat Washer (Items 7, 11)

and secure with a M8 Nyloc Nut (Item 8).

Fully tighten all fasteners and place Nut Caps

over nuts (Either Item 5 or 9).

2.1

2.2

2.3

Choose which side for the Slimline II Tray

you'd like to install the Awning.

On the chosen side, slide six M8 Nyloc Nuts

(Item 8) in the T-slot channel at the corner of

the Tray making sure the M8 Nyloc Nut

thread is facing upward. Two M8 Nyloc Nuts

will be used for each Mounting Bracket

(Item 1). Spacing of the Nyloc Nuts will

depend on the length of the Tray and the

Awning. The Mounting Brackets

must be positioned between two Slats.

10MM

13MM

AWNING BRACKET INSTALLATION - SLIMLINE RACK

10MM

Drill a 6.5mm hole on the marked positions.

Place the three Mounting Brackets on the

Rack so the holes in the bracket line up

with the holes you drilled. Insert three

M6 x 16 Hex Bolts (Item 1) and secure with

M6 x 12 x 1SS Flat Washers and M6 Nyloc

Nuts (Items 3, 4).

3.1

3.2

Choose which side for the Slimline II Tray

you'd like to install the Awning.

On the chosen side, place the Mounting

Brackets (Item 2) between two slats, starting

at either end of the side proﬁle of the Rack.

Place the third Mounting Bracket in the

center. Make sure the two holes on the

bracket are facing upward. Using a white

marking pen, mark the three center holes

in each Mounting Bracket.

Remove the three Mounting Brackets.

With the help of a friend, lift the Awning up

and move towards the Basket while

lining-up the bolts in the Awning with the

holes in the Mounting Brackets. Fit Flat

Washers and Nyloc Nuts (Items 3,4 or 7, 8)

onto each bolt.

Fully tighten all fasteners and place Nut Caps

over nuts (Either Item 5 or 9).

6.5MM

Depending on the type of Awning Extrusion,

slide either three M6 x 16 Hex Bolt or three

M8 x 20 Hex Bolts (Items 1 or 6) into the top

slot and three into the bottom slot of the

extrusion.

10MM

13MM

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner Dealer in person or Online.

COMPLETION

4.1

Congratulations! You did it. Take a step back and admire your work!

5Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Front Runner Accessori per automobili

Front Runner

Front Runner SlimSport KSFR002 Manuale utente

Front Runner

Front Runner FAFE001 Manuale utente

Front Runner

Front Runner TBRA020 Manuale utente

Front Runner

Front Runner RRAC120 Manuale utente

Front Runner

Front Runner LASJ003 Manuale utente

Front Runner

Front Runner SSAM008 Manuale utente

Front Runner

Front Runner RRAC119 Manuale utente

Front Runner

Front Runner SSDS105 Manuale utente

Front Runner

Front Runner FAMG001 Manuale utente

Front Runner

Front Runner TRCA004 Manuale utente

Front Runner

Front Runner LALD004 Manuale utente

Front Runner

Front Runner 200 Series Manuale utente

Front Runner

Front Runner SSLD001 Manuale utente

Front Runner

Front Runner SSDR005 Manuale utente

Front Runner

Front Runner RRAC178 Manuale utente

Front Runner

Front Runner RRAC129 Manuale utente

Front Runner

Front Runner SSDS110 Manuale utente

Front Runner

Front Runner SLIMLINE II Manuale utente

Front Runner

Front Runner FATF006 Manuale utente

Front Runner

Front Runner RRAC202 Manuale utente

Front Runner

Front Runner SSDR003 Manuale utente

Front Runner

Front Runner SSDS115 Manuale utente

Front Runner

Front Runner SAFE010 Manuale utente

Front Runner

Front Runner SSDS109 Manuale utente

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Aries

Aries 203015 Manuale utente

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente