Front Runner LALD004 Manuale utente
LALD004_REV_A02 © COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
LALD004
ENG
1
IMPORTANT WARNING!
Ladder
land rover discovery 3 / 4
FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL
THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS
TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
Thank you for purchasing a Front Runner 40" LED Light Bar Brackets.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
LALD004_REV_A02
2
© COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
1
2
3
TOOLS NEEDED
1 1 X Ladder
2 1 X Z-Clamp
3 1 X Foam Rubber 600mm Long
IN THE BOX
FIGURE 1.1
T30
10MM 13MM
GET ORGANIZED
1
LALD004_REV_A02
3
© COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
PREPARE FOR LADDER FITMENT
2
2.1
2.2
2.3
Remove the screw inside the door handle.
Open the top rear door and remove the four
Torx Bolts (T30) as indicated by the arrows.
You will need to lift the rubber door seal in
order to remove the far left Torx Bolt.
Remove the trim around the door stricker.
T30
LALD004_REV_A02
4
© COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
PREPARE FOR LADDER FITMENT
2
2.4
2.5
2.6
Disconnect the electrical connecter as
indicated (Including rear camera if fitted).
Remove the interior trim panel by pulling it
away from the vehicle's body. Take care not
to damage any of the plastic retaining clips.
Loosen and remove the three hex nuts shown.
10MM
LALD004_REV_A02
5
© COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
PREPARE FOR LADDER FITMENT
2
LADDER FITMENT
3
2.7
Remove the rear number plate light cluster
from the vehicle.
Before removing the protective backing on
the Foam Rubber (Item 3) make sure
that the surface where it will be adhered
is clean.
Follow the outer line of the number plate light
cluster and adhere the Foam Rubber
accordingly. See Step 2.7.
Open the bottom rear door and close the top
rear door, so as to not accidentally lock the
rear door.
3.1
Hook the lip at the top of the Ladder over the
top edge of the Rear Door through the gap
between the door and the vehicle's roof. See
Step 3.2.
Push the top lip against the top edge of the
rear door.
3
LALD004_REV_A02 © COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
6
LADDER FITMENT
3
3.2
3.3
3.4
Open the top rear door and remove the outer
hex bolt on the rear left hand side door hinge.
Ensure the top lip from the Ladder is against
the top edge of the rear door (Refer to Step
3.1), Place the Z-Clamp (Item 2) over the
top lip, lining up the hole in the Z-Clamp
with the bolt hole. Secure the Z-Clamp to the
vehicle using the hex bolt removed.
Reconnect the electrical plugs removed in
Step 2.5, Refit the trim revoved in Steps 2.2 to
2.4 and fasten the torx bolts removed in
Step 2.1.
Align the holes in the bottom of the Ladder
with the holes in the vehicle's body (behind
the rear number plate light cluster removed
earlier).
Place the rear number plate light cluster over
the bottom of the Ladder and secure using the
hex nuts removed in Step 2.6.
13MM
T30
2
LALD004_REV_A02 © COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
7
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or Online.
COMPLETION
4
9
4.1
10mm
Congratulations! You did it. Take a step back and admire your work!
4.1
Indice
Altri manuali Front Runner Accessori per automobili
Front Runner
Front Runner Slimline II KRVA002T Manuale utente
Front Runner
Front Runner Slimline II KRKS007T Manuale utente
Front Runner
Front Runner RRAC190 Manuale utente
Front Runner
Front Runner KRJW021T Manuale utente
Front Runner
Front Runner FAJL004 Manuale utente
Front Runner
Front Runner RRAC120 Manuale utente
Front Runner
Front Runner LAMS004 Manuale utente
Front Runner
Front Runner SSDR010 Manuale utente
Front Runner
Front Runner SSDS602 Manuale utente
Front Runner
Front Runner SLIMLINE II Manuale utente
Front Runner
Front Runner Pro Water Tank with Strap Manuale utente
Front Runner
Front Runner FAJK010 Manuale
Front Runner
Front Runner RRAC119 Manuale utente
Front Runner
Front Runner RRAC203 Manuale utente
Front Runner
Front Runner JADA014 Manuale utente
Front Runner
Front Runner SSDS113 Manuale utente
Front Runner
Front Runner SSDR002 Manuale utente
Front Runner
Front Runner TBMK011 Manuale di istruzioni
Front Runner
Front Runner RRAC178 Manuale utente
Front Runner
Front Runner FAJK009 Manuale utente
