Front Runner SSDS113 Manuale utente
SSDS113_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
SSDS113
ENG
1
60 min
IMPORTANT WARNING!
Thank you for purchasing a Front Runner Drawer Deck Completion Set.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
Toyota Fortuner (2005-2015)
Drawer Deck Completion Set
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
SSDS113_REV_A00
2
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
1
13
14
13
15
16
17
12
10
11
7
10
7
9
8
7
6
5
4
3
2
1
TOOLS NEEDED
17MM
13MM
10MM
10MM
8MM
1 2 X Side Deck LH + RH
2 4 X M6 x 12 Button Head
3 2 X Top Rear Wing LH + RH
4 2 X Bottom Rear Wing LH + RH
5 4 X M6 x 12 x 1SS Flat Washer
6 8 X M6 Nyloc Nut
7 12 X M6 x 19 x 1SS Flat Washer
8 2 X Adjustable Front Wing LH + RH
9 2 X Fixed Front Wing LH + RH
10 8 X M6 x 16 Hex Bolt
11 4 X M6 Spring Washer
12 2 X Pinch Weld 350mm
13 2 X Front Face LH + RH
14 4 X M5 x 10 Button Head
15 4 X M5 x 10 x 1SS Flat Washer
16 4 X M5 Nyloc Nut
17 2 X 37mm Laser Cut Carabiner
IN THE BOX
FIGURE 1.1
4mm
3mm
GET ORGANIZED
1
SSDS113_REV_A00
3
FIT AND SECURE
2
Secure the Fixed Front Wings (Item 9) on the
left and right side of the Drawer by using
M6 x 16 Hex Bolts, M6 Spring Washers and
M6 x 19 x 1SS Flat Washers
(Items 10, 11 & 7) as shown.
13MM
2.1
2.2
2.3
You will need to relocate the two front
D-Rings on the Drawer. Loosen the D-Rings
and unclip the Cage Nuts. Move the
Cage Nuts to the new positions as shown
and secure.
Place the Drawer System into the vehicle
taking care not to damage any of the interior
plastic panels. Position the Draw System
as close to the rear door as possible and
center in the vehicle.
Loosen and remove the the two rear seats.
Use the bolts that you have removed to
secure the D-Rings supplied with the
Drawer system (SSDR005) as shown.
10 11
7
9
10MM
17MM
SSDS113_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE
2
Fit the Top Rear Wing (Item 3) to the Bottom
Rear Wing (Item 4) using M6 x 12 Button
Heads, M6 x 12 x 1SS Flat Washers and
M6 Nyloc Nuts (Items 2, 5 & 6) as shown.
4MM
2.4
2.5
2.6
Loosen and remove the two rear
Button Head Screws on either side, securing
the deck to the drawer. Slide the Bottom Rear
Wings (Item 4) between the drawer and the
deck. Refit the Button Head
Screws and tighten.
Loosely assemble the Adjustable Front Wings
(Item 8) to the Fixed Front Wings (Item 9)
using M6 x 16 Hex Bolts, M6 x 19 x 1SS Flat
Washers and M6 Nyloc Nuts
(Items 10, 7 & 6) as shown.
Do this on the left and right side of the
Drawer System.
The fasteners will be fully tightened in
Step 2.9.
10
7
8
6
7
9
Drawer Top
Button Head
2
3
6
5
10MM
10MM
4MM
10MM
SSDS113_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE
2
Place the Side Decks (Item 1) onto the
Drawer making sure that you slide it into
the C-clip of the Front and Rear
Side Wings. Push the Adjustable Front Wing
up against the Side Deck.
Carefully remove the Side Deck so that the
adjustable Front Wings do not move.
Secure the Adjustable Front Wings and refit
the Side Decks.
3MM
2.7
2.8
2.9
Secure the Drawer System in position using
the 37mm Laser Cut Carabiner (Item 17) and
the Turn Buckles (supplied with SSDR005)
as shown.
Tighten the wing nut on each Turn Buckle to
prevent it from coming loose.
Fit the Pinch Weld (Item 12) onto the
Front Faces (Item 13) before securing the
Front Faces to the Drawer.
Secure the Front Face to the Drawer using
M5 x 10 Button Heads, M5 x 10 x 1SS
Flat Washers and M5 Nyloc Nuts
(Items 14, 15 & 16) as shown.
12
17
13
15
16
1
8MM
SSDS113_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
6
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
4
Now's the time to visit your favorite Front Runner Dealer in person or Online.
COMPLETION
3
9
3.1
Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
10mm
Congratulations! You did it. Take a step back and admire your work!
Indice
Altri manuali Front Runner Accessori per automobili
Front Runner
Front Runner JADA010 Manuale utente
Front Runner
Front Runner VACC120 Manuale utente
Front Runner
Front Runner TBRA020 Manuale utente
Front Runner
Front Runner TBRA039 Manuale utente
Front Runner
Front Runner LALD004 Manuale utente
Front Runner
Front Runner SSDR011 Manuale utente
Front Runner
Front Runner FAJK003 Manuale utente
Front Runner
Front Runner TRCA005 Manuale utente
Front Runner
Front Runner FSLI023 Manuale utente
Front Runner
Front Runner JCH004 Manuale utente
Front Runner
Front Runner LALD006 Manuale utente
Front Runner
Front Runner TRCA009 Manuale utente
Front Runner
Front Runner SSDS802 Manuale utente
Front Runner
Front Runner RRAC051 Manuale utente
Front Runner
Front Runner LASJ003 Manuale utente
Front Runner
Front Runner LALD009 Manuale utente
Front Runner
Front Runner RRAC190 Manuale utente
Front Runner
Front Runner FSLI022 Manuale utente
Front Runner
Front Runner SAFE010 Manuale utente
Front Runner
Front Runner KRRK001T Manuale di istruzioni
