Fujitsu BX630 - PRIMERGY - S2 Dual Manuale utente

PRIMERGY BX630 S2

Scalable Server Blade

Operating Manual

Edition October 2008

Comments…Suggestions…Corrections…

The User Documentation Department would like to

know your opinion of this manual. Your feedback helps

us optimize our documentation to suit your individual

needs.

Feel free to send us your comments by e-mail to

[email protected]ujitsu.com.

Certified documentation

according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system

which complies with the requirements of the standard

DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

BX630 S2 Operating Manual

Contents

1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Concept and target group of this manual . . . . . . . . . . . . 6

1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 7

1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . 12

1.5 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 Overview: Installation Procedure . . . . . . . . . . . . . . . 15

3 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.2 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.3 Environmental protection . . . . . . . . . . . . . . . . . . . 20

4 Installing the Hardware . . . . . . . . . . . . . . . . . . . . 23

4.1 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . 23

4.2 Unpacking the Server Blade . . . . . . . . . . . . . . . . . . 23

4.3 Installing the Server Blade in the Basic Unit . . . . . . . . . 24

4.4 Connecting Devices . . . . . . . . . . . . . . . . . . . . . . 28

5 Installation and Operation . . . . . . . . . . . . . . . . . . . 31

5.1 Control and Connection Panel . . . . . . . . . . . . . . . . 32

5.2 Switching the Server Blade On/Off . . . . . . . . . . . . . . 35

5.3 Configuring the Server Blade . . . . . . . . . . . . . . . . . 35

5.4 Updating the Firmware (BIOS and BMC) . . . . . . . . . . . 38

Operating Manual BX630 S2

Contents

6 BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.1 Entering the BIOS Setup . . . . . . . . . . . . . . . . . . . . 43

6.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

6.3 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.4 Advanced menu . . . . . . . . . . . . . . . . . . . . . . . . . 48

6.4.1 Peripheral Configuration . . . . . . . . . . . . . . . . . . . . . 50

6.4.2 Advanced System Configuration . . . . . . . . . . . . . . . . . 53

6.4.3 Power On/Off menu . . . . . . . . . . . . . . . . . . . . . . . . 54

6.4.4 IPMI menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

6.4.4.1 IPMI LAN parameters . . . . . . . . . . . . . . . . . . . . . 59

6.5 Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.6 Server menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.6.1 CPU Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

6.6.2 Memory Status . . . . . . . . . . . . . . . . . . . . . . . . . . 67

6.6.3 Console Redirection . . . . . . . . . . . . . . . . . . . . . . . 69

6.7 Boot menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

6.8 Exit menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

7 Troubleshooting and Tips . . . . . . . . . . . . . . . . . . . . 73

8 Hot-plug components . . . . . . . . . . . . . . . . . . . . . . 75

8.1 Hot-plug disk drives . . . . . . . . . . . . . . . . . . . . . . . 75

8.2 Handling hard disk drives and HDD modules . . . . . . . . . 77

8.3 Installing/removing the dummy module . . . . . . . . . . . . 78

8.4 Installing/removing a hard disk module . . . . . . . . . . . . 79

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

BX630 S2 Operating Manual 5

1 Preface

The PRIMERGY BX630 S2 server blade is a scalable AMD-based dual-socket

server blade. It offers several new forward-looking technologies such as quad-

core processors, 2.5-inch SAS or SATA-II hard disk drives, four 1-Gbit/s

onboard Ethernet LAN channels and an optional dual-channel 4-Gbit/s Fibre

Channel (FC) connection. Two BX630 S2 dual-socket server blades can be

connected to form a quad-socket server blade with 16 processor cores.

Figure 1: PRIMERGY BX630 S2 configurations

The PRIMERGY BX630 S2 scalable server blade is designed for the BX600 S3

basic unit, but it can also be installed in slots 1-3 and 5-9 of the BX600 S2 basic

unit.

IIn the latter case, however, only 2 of the 4 onboard Ethernet channels of

the BX630 S2 server blade can be used.

Security functions in the BIOS Setup protect the data on the server blade from

unauthorized manipulation.

Dual-socket server blade Quad-socket server blade

6 Operating Manual BX630 S2

Concept and target group of this manual Preface

Depending on the configuration, the PRIMERGY BX630 S2 scalable server

blade occupies one or two slots in the PRIMERGY BX600 S2 or the BX600 S3

basic unit.

1.1 Concept and target group of this manual

This operating manual is intended for those responsible for installing the

hardware and ensuring that the system runs smoothly. It contains all the infor-

mation you need to put your PRIMERGY BX630 S2 server blade into operation.

The information in this manual refers to the BX630 S2 dual-socket server blade.

How to connect two BX630 S2 dual-socket server blades to form a quad-socket

server blade is described in the Options Guide.

For a brief overview of the installation steps see chapter 2 on page 15ff.

To understand the various expansion options, you will need to be familiar with

the fields of hardware and data transmission and you will require a basic

knowledge of the underlying operating system.

BX630 S2 Operating Manual 7

Preface Documentation overview

1.2 Documentation overview

Information on your PRIMERGY BX630 S2 is provided in the following

documents:

– Flyer "Quick Start Software - Quick Installation Guide" (only provided as

hard copy)

– Manual "Safety Notes and other Important Information"

– Manual "Guarantee"

– Manual "Ergonomics"

– Manual "Returning used devices"

– Flyer "Helpdesk"

– Operating Manual for PRIMERGY BX630 S2 Scalable Server Blade

– Options Guide for PRIMERGY BX630 S2 Scalable Server Blade

IPRIMERGY manuals are available in PDF format on the ServerBooks

DVD. The ServerBooks DVD is part of the ServerView Installation

Manager Suite supplied with every server.

The PDF files of the manuals can also be downloaded free of charge

from the Internet. The overview page showing the online documentation

available on the Internet can be found using the URL:

http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can

be accessed using the Industry standard servers navigation option.

If you need a replacement copy of the ServerBooks DVD, send the

details of your server to the following e-mail address: [email protected]jitsu.com.

Further sources of information:

– Manual for the monitor

– Documentation for boards and drives

– Documentation for your operating system

– Information files on your operating system

IFor information on installing and operating PRIMERGY BX6xx server

blades that applies to all server blade models, see the operating manual

for your PRIMERGY BX600 S2 or BX600 S3 basic unit.

8 Operating Manual BX630 S2

Features Preface

1.3 Features

Processors

In the BX630 S2 dual-socket server blade, one (basic configuration) or two

AMD Opteron quad-core processors of the 23xx DP and 83xx MP series ensure

extremely high data throughput and system performance.

All processors have a 2-MB second-level cache (SLC).

IIt is not possible to use CPUs with different clock rates or cache capacity

in a server blade.

In the BX630 S2 quad-socket server blade, only processors of the

Opteron 83xx MP series are allowed.

For upgrading processors see the Options Guide; for exchanging processors

see the Service Supplement.

Memory

The BX630 S2 dual-socket server blade has eight memory slots. Each

processor is assigned four memory slots. Two memory slots make up one

memory bank. The memory slots must be fitted by bank, i.e. with pairs of

memory modules. The server blade supports memory modules of the type

DDR2 667 with 512 MB, 1 GB, 2 GB or 4 GB capacity, so the maximum config-

uration is 32 GB (64 GB in a quad-socket server blade). ECC with memory

scrubbing and ChipKill™ are supported. Only memory modules of the same

capacity can be installed in the same memory bank.

How to install memory modules is described in the Options Guide.

LAN availability

The BX630 S2 dual-socket server blade has two onboard Ethernet LAN

controllers with two 1-Gbit/s Ethernet channels each. The Ethernet LAN

connection can be implemented via switch blades or via pass-thru blades on the

back of the basic unit. For more information see the operating manual for the

basic unit.

IYou can only use the two 1-Gbit/s Ethernet channels of the second

onboard LAN controller in connection with the BX600 S3 basic unit and

the Gbit Ethernet LAN switch blade (SB9f) 12 x 1 Gbit.

BX630 S2 Operating Manual 9

Preface Features

Graphics controller

The PRIMERGY BX630 S2 scalable server blade has an onboard graphics

controller (Matrox MGA-200) which is integrated in the iRMC controller. You can

connect a monitor via the VGA interface (via breakout cable) on the front of the

server blade or via the KVM blade on the back of the basic unit.

Optional Fibre Channel or Ethernet I/O module (daughter card)

You can fit the BX630 S2 dual-socket server blade with an I/O daughter card to

connect to a SAN or for additional Ethernet connections. The BX630 S2 quad-

socket server blade allows two I/O daughter cards to be installed.

To be able to use the additional I/O functionality, at least one FC pass-thru blade

or switch blade, or Ethernet pass-thru blade or switch blade must be installed in

slot NET3 of the basic unit.

The following I/O daughter cards are available:

– 4-Gbit/s Fibre Channel I/O module (PCIe), allows transfer rates of 1, 2 or 4

Gbit/s and supports multiple Fibre Channel storage subsystems with the

corresponding versions.

IYou can operate the 4-Gbit/s Fibre Channel I/O module only with a

BX600 S3 basic unit and only in combination with a Brocade SW-

4016 D4 Fibre Channel switch blade or with a 4 Gbit FC pass-thru

blade. For more information see the operating manual for the

BX600 S3 basic unit.

– Gigabit Ethernet I/O module (PCIe), also supports TOE (TCP/IP offload

engine) and iSCSI

– 10-Gbit Ethernet I/O module (PCIe)

IThe 10-Gbit Ethernet I/O module (PCIe) can only be used in combi-

nation with a 10-Gbit switch blade 10/2. For more information see the

operating manual for the basic unit.

IYou must not install server blades with different I/O modules in the same

BX600 S2 or BX600 S3 basic unit.

How to install I/O modules later is described in the Options Guide.

10 Operating Manual BX630 S2

Features Preface

High availability and reliability

When memory data is accessed, 1-bit errors in the main memory are recog-

nized and automatically corrected with the ECC (Error Correcting Code)

method.

ASR&R (Automatic Server Reconfiguration and Restart) restarts the system in

the event of an error and automatically "hides" the defective system compo-

nents.

The PDA (Prefailure Detection and Analyzing) technology from Fujitsu

Technology Solutions analyzes and monitors all components that are important

for system reliability.

The onboard SAS RAID controller supports RAID levels 0 and 1 by default, thus

increasing the system's availability. If you are using SATA-II hard disk drives, you

can implement RAID levels 0 and 1 using Promise 20319 to increase the

system's availability.

Server management

Server management is implemented using the supplied ServerView software and

PDA technology. PDA reports the threat of a system error or overloading to the

system administrator in good time, so that preventive measures can be taken.

ServerView allows the management of all PRIMERGY servers in the network via

a central console. ServerView supports the following functions:

●Monitoring of the ambient and CPU temperatures

●Watchdog timer for Automatic Server Reconfiguration and Restart (ASR&R)

if memory modules or processors fail

●Power monitoring

●End-of-life monitoring of the fans with prefailure notification

●Watchdog timer for monitoring the operating system and applications with

ASR&R

The supplied deployment software simplifies and speeds up the installation of

multiple servers. For further information see the relevant documentation.

For further information on the ServerView server management software see the

relevant documentation.

Altri manuali per BX630 - PRIMERGY - S2 Dual

Indice

Altri manuali Fujitsu Server

Fujitsu

Fujitsu PRIMERGY TX150 S2 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX900 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX300 S8 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX1330 M4 Manuale utente

Fujitsu

Fujitsu S540 Manuale utente

Fujitsu

Fujitsu PRIMERGY TX100 S1 Manuale utente

Fujitsu

Fujitsu PRIMERGY TX1310 M5 Manuale utente

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Manuale utente

Fujitsu

Fujitsu PRIMERGY TX100 S3 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX600 PG-LNB101 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX330 S1 Manuale utente

Fujitsu

Fujitsu FUTRO Z220 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX600 S5 Manuale utente

Fujitsu

Fujitsu PRIMERGY TX150 S8 Manuale utente

Fujitsu

Fujitsu Primergy BX920 S3 Manuale utente

Fujitsu

Fujitsu BS2000 SE Series Manuale utente

Fujitsu

Fujitsu PRIMEQUEST 500A Series Manuale utente

Fujitsu

Fujitsu PRIMERGY RX200 S8 Guida utente

Fujitsu

Fujitsu Primergy RX300 S3 Manuale utente

Fujitsu

Fujitsu Primergy BX620 S2 Guida rapida

Fujitsu

Fujitsu PRIMERGY RX100 S6 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX900 Manuale utente

Fujitsu

Fujitsu FUTRO S550 Manuale utente

Fujitsu

Fujitsu PRIMERGY TX2540 M1 Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente