GÜDE Expert Net Control 2304 Manuale utente

Manual

Expert Net Control 2304

Manual Ver. 1.0.1

from Firmware Ver. 1.0

Table of contents

1. Device Description 5

1.1 Security Advice .............................................................................................................. 6

1.2 Content of Delivery ........................................................................................................ 6

1.3 Description ..................................................................................................................... 6

1.4 Installation ...................................................................................................................... 7

1.4.1 Connection Example ................................................................................................. 8

1.5 Technical Specifications ................................................................................................ 9

1.6 Sensor ........................................................................................................................... 10

2. Operating 12

2.1 Operating the device directly ..................................................................................... 13

2.2 Control Panel ................................................................................................................ 13

2.3 Maintenance ................................................................................................................ 15

2.3.1 Maintenance Page ................................................................................................. 18

2.3.2 Configuration Management ................................................................................... 19

2.3.3 Bootloader Activation ............................................................................................. 20

3. Configuration 23

3.1 Output Ports ................................................................................................................ 24

3.1.1 Watchdog ............................................................................................................... 25

3.2 Input Ports .................................................................................................................... 27

3.3 Ethernet ........................................................................................................................ 28

3.3.1 IP Address ............................................................................................................... 28

3.3.2 IP ACL ..................................................................................................................... 29

3.3.3 HTTP ....................................................................................................................... 31

3.4 Protocols ....................................................................................................................... 32

3.4.1 Console ................................................................................................................... 32

3.4.2 Syslog ..................................................................................................................... 33

3.4.3 SNMP ...................................................................................................................... 33

3.4.4 Radius ..................................................................................................................... 35

3.4.5 Modbus TCP ........................................................................................................... 37

3.4.6 MQTT ...................................................................................................................... 38

3.5 Clock .............................................................................................................................. 39

3.5.1 NTP ......................................................................................................................... 39

3.5.2 Timer ...................................................................................................................... 40

3.5.3 Timer Configuration ............................................................................................... 40

3.6 Sensors .......................................................................................................................... 47

3.6.1 Port Switching ......................................................................................................... 48

3.7 E-Mail ............................................................................................................................ 49

3.8 Front Panel ................................................................................................................... 51

Table of contents

4. Specifications 52

4.1 Automated Access ....................................................................................................... 53

4.2 Messages ....................................................................................................................... 53

4.3 IP ACL ............................................................................................................................ 55

4.4 IPv6 ................................................................................................................................ 56

4.5 Radius ............................................................................................................................ 56

4.6 SNMP ............................................................................................................................ 57

4.6.1 Device MIB 2304 .................................................................................................... 60

4.7 SSL ................................................................................................................................. 61

4.8 Console .......................................................................................................................... 63

4.8.1 SSH .......................................................................................................................... 67

4.8.2 Console Cmd 2304 ................................................................................................. 68

4.9 Modbus TCP .................................................................................................................. 77

4.9.1 Sensor Tables ......................................................................................................... 82

4.10 MQTT ............................................................................................................................. 83

4.10.1 Example HiveMQ .................................................................................................... 85

5. Support 87

5.1 Data Security ................................................................................................................ 88

5.2 Contact .......................................................................................................................... 88

5.3 Declaration of Conformity .......................................................................................... 89

5.4 FAQ ................................................................................................................................ 89

Index

Device Description

1 Device Description

1.1 Security Advice

·The device may only be used for its intended purpose.

·The device must be mounted in a housing / control cabinet in the end application and

must not be accessible during operation.

·Never work when voltage is applied.

·The device may only be installed and used by qualified personnel. The manufacturer

accepts no liability for damage or injury caused by improper use of the device.

·It is not possible for the customer to repair the device. Repairs may only be carried out

by the manufacturer.

·Connect the device to the supply mains or to a suitable low-voltage source (see tech-

nical data for details).

·The device may only be operated on the supply mains on a circuit with a fuse protec-

tion of max. 16 A.

·The power cables and plugs used must be in perfect condition.

·The device is only intended for use in dry and clean environments.

·The thermal specifications must be observed.

·Please also observe the safety instructions and operating instructions of the other

devices that are connected to the device.

·The device is not a toy. It must not be stored or operated within the reach of children.

·Do not leave packaging material lying around carelessly. Plastic sheets/bags, Styro-

foam parts, etc. could become a dangerous toy for children. Please recycle the pack-

aging material.

·If you are not clear about the correct connection or if any questions arise that are not

clarified by the operating instructions, please contact our support.

1.2 Content of Delivery

The package includes:

·Expert Net Control 2304

·Quick Start Guide

1.3 Description

The Expert Net Control 2304 can switch 8 different relay outputs and monitor 8 passive

signal inputs. The device has the following features:

·8 switchable, potential-free relay outputs, switching voltage 230 V AC 16 A / 24 V DC,

10 A

·Relays dispose of high contact reliability also at very small loads

·8 passive inputs for monitoring NO and NC devices, e.g. door contacts, smoke detect-

ors etc.

·Operation with 230 V AC or 24 V DC voltage

·Optional sensor for environmental monitoring (temperature, humidity and air pressure)

Device Description

·Console commands via SSH and Telnet

·SSH support with public key and passwords

·Individually parameterisable switch-on delay of all outputs

·Programmable timetables and turn-on/turn-off sequences

·Individually adjustable watchdog for each output, which switches depending on ac-

cessibility (network ping)

·Dual TCP/IP stack with IPv4 and IPv6 support (IPv6-ready)

·Control and monitoring of the device via Ethernet with an integrated web server with

SSL encryption (TLS 1.1, 1.2, 1.3)

·Control and configuration with CGI parameters and JSON messages via HTTP (REST

API)

·SNMP (v1, v2c and v3, traps)

·MQTT 3.1.1 Support

·Modbus TCP support

·Radius support

·Generation of messages (e-mail, syslog and SNMP traps) and switching of relays de-

pending on sensor measurement limits

·Firmware update during operation via Ethernet possible

·Encrypted e-mails (SSL, STARTTLS)

·Access protection through IP access control

·Low own consumption

·Developed and produced in Germany

1.4 Installation

1. Low voltage power supply

2. 8x passive inputs (each with GND)

3. Pushbuttons for Select and OK

4. 4x 7-segment display (partly with unit LEDs e.g. "°C" )

5. 8x plain text displays (on/off) for the status of inputs and outputs

6. Indicators ("Input" or "Output") for the 8 plain text displays (on/off)

Device Description

7. Status LED

8. Ethernet port status and activity (green and orange)

9. external sensor ("Sen.") plugged in indicator

10. Network connection (RJ45)

11. sensor connection (RJ45)

12. AC mains power supply

13. 8x relay switching contacts (NO)

Commissioning

·Connect the device to the mains supply or to a suitable low voltage source (see tech-

nical data).

·Plug the network cable into the Ethernet socket (RJ45).

·Connect the relays to the loads that are to be operated.

·Establish contact between the lines to be monitored and the digital inputs.

·Connect a sensor (if available).

1.4.1 Connection Example

Here is an example with block diagram in which the device is supplied with 230V AC and

in which eight AC loads (L1 - L8) are connected. In addition, the inputs are assigned

eight switches (S1 - S8).

As an alternative to connecting "In 1-8" and "GND", voltages can also be fed in

between "In 1-8" and GND. The maximum input voltage is 24V, voltages below 3V are

detected as LOW state, and voltages above 8V are detected as HI.

Device Description

1.5 Technical Specifications

Connections

1 x Ethernet connection RJ45

1 x RJ45 for external sensor

1 x AC mains connection, picoMAX 7.5

1 x low voltage, AK1350

8 x inputs In1 ... In8, AK1350

8 x relay switching contacts NO, picoMAX 5.0

Network connection

10baseT / 100baseTX Ethernet

Relay outputs

Out1 ... Out8

max. 240V AC 16A, 50/60Hz

24V DC 10A

Inputs

In1 ... In8

screw terminal, AK1350/..DS-3.5-GREY

digital input, internal pull-up

active: max. 24V, < 3V LOW, > 8V HI

passive: switching contact

Power supply

internal power supply:

100V to 240V AC -15% ...+10%, 50/60 Hz, max 0.3A.

Low voltage:

12V to 24V AC -10% ... +10%, 50/60Hz, max 0.8A

12V to 24V DC -5% ... +25%, max 0.8A

internal fuse protection: 1.75A Typical I2t (A2s) = 1.5

Protection class

Class II

Environment

·Ambient temperature

·Storage temperature

·Humidity

0°C to 50°C

-20°C - 70°C

0% - 95% (non-condensing)

Housing

White plastic

Dimensions

143mm x 65mm x 90mm (L x H x D)

Weight

approx. 400g

AK1350 /DS-3.5-GREY

Connection technology

Screw terminal

Solid conductor

0.08 ... 1.5 mm² solid conductor

Fine-stranded conductor (flexible)

0.08 ... 1.5 mm² fine-stranded conductor

Fine stranded conductor; wire end ferrule

0.14 ... 0.5 mm² fine-stranded conductor

Stripping length

5.0 mm

picoMAX® eCOM 5.0 and 7.5

Connection technology

Push-in CAGE CLAMP®

Actuation type

Push-button

Solid conductor

0.2 ... 2.5 mm² / 24 ... 12 AWG

Fine-stranded conductor

0.2 ... 2.5 mm² / 24 ... 12 AWG

Fine stranded conductor; with insulated

ferrule

0.25 ... 1.5 mm²

Stripping length

9.0 ... 10.0 mm

Device Description

1.6 Sensor

One external sensor can be connected to the Expert Net Control 2304. The following

sensors are currently available

Product Name

7101

7104-1

7105-1

7106-1

Calibrated

Sensor

7104-2

7105-2

7106-2

Cable length

Connector

RJ45

temperature range

-20°C to +80°C at

±2°C (maximum)

and ±1°C (typical)

-20°C to +80°C at

±2°C (maximum)

and ±1°C (typical)

-20°C to +80°C at

±2°C (maximum)

and ±1°C (typical)

-20°C to +80°C at

±2°C (maximum)

and ±1°C (typical)

air humidity range

(non-condensing)

0-100%, ±3%

(maximum) and

±2% (typical)

0-100%, ±3%

(maximum) and

±2% (typical)

air pressure range

(full)

± 1 hPa (typical)

at 300 ... 1100

hPa, 0 ... +40 °C

air pressure range

(ext)

± 1.7 hPa (typical)

at 300 ... 1100

hPa, -20 ... 0 °C

Protection

IP68

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GÜDE Strumento di misura

GÜDE

GÜDE expert net control 2190 GSM Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente