GarrettCom Magnum Quad-Series Manuale utente

www GarrettCom com

Corporate Headquarters

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email support@garrettcom.com

Magnum Quad-Series

Fiber Switches

Installation and User Guide

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

Magnum



Quad-Series

Fiber Switches

Installation and User Guide

Part #: 84-00063 (Rev. D 12/02)

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a

registered trademark of GarrettCom, Inc.

Important: The Magnum Quad Series Fiber Switch contains no user

serviceable parts. Attempted service by unauthorized personnel shall render all

warranties null and void. If problems are experienced with Magnum Quad

Series Fiber Switch products, consult Section 6, Troubleshooting, of this User

Guide.

of this publication may be reproduced without prior written permission from

GarrettCom, Inc.

Printed in the United States of America.

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email [email protected]

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not

installed and used properly, that is in strict accordance with the manufacturer's

instructions, may cause interference to radio communication. It has been tested and

found to comply with the limits for a Class A computing device in accordance with the

specifications in Subpart J of Part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference, in which case the user at his own expense will be required to take whatever

measures may be required to correct the interference.

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

TABLE OF CONTENTS Page

1.0 SPECIFICATIONS ............................................................................... 1

1.1 Technical Specifications...................................................................... 1

1.2 Ordering Information........................................................................... 3

2.0 INTRODUCTION ................................................................................. 4

2.1 Inspecting the Package and Product .................................................... 4

2.2 Product Description - Magnum Quad-Series Fiber Switches .............. 5

2.2.1 Magnum Quad-Series chassis models.......................................... 5

2.2.2 Quad-port modules, 100Mb fiber ...................................................... 7

2.2.3 Quad-port modules, 10 Mb fiber.................................................. 7

2.2.4 Quad-Port Module, RJ-45 (copper) ............................................. 8

2.2.5 Combo “3 + 1” Quad Port Modules, 3@RJ-45 and 1@fiber....... 8

2.2.6 Frame Buffering and Latency...................................................... 9

2.3 Features and Benefits......................................................................... 11

2.4 Applications....................................................................................... 12

3.0 INSTALLATION................................................................................ 15

3.1 Locating Magnum Quad-Series Switches.......................................... 15

3.2 Connecting Ethernet Media ............................................................... 16

3.2.1 Connecting Fiber Optic ST-type, “twist-lock”.......................... 16

3.2.2 Connecting Fiber Optic SC-type, "Snap-In".............................. 17

3.2.3 Connecting Single-Mode Fiber Optic........................................ 17

3.2.4 Connect Twist Pair (RJ-45,CAT3, CAT5, Unsh or Shiel)......... 17

3.3 Table-Top or Shelf Mounting............................................................ 18

3.3.1 Wall (or Vertical Surface) Mounting, 8-port QS580................. 18

3.3.2 Rack-mounting, models QS5108 and QS5116........................... 18

3.4 RJ-45 ports, int jump set for 10/100Mb............................................. 20

3.5 Fiber 100Mb ports, int jump set for 100Mb fixed ............................. 21

3.6 Combo(3+1) ports, int jump set for 10/100 RJ-45 Auto-Neg............ 22

3.7 Fiber 10Mb ports, int jump set for 10Mb fixed Half- or.................... 23

3.8 Powering the Magnum Quad-Series Switch...................................... 24

3.9 Quad Port Module (QPM) Installation............................................... 25

3.9.1 Preparation for Installing and Removing QPMs........................ 25

3.9.2 Installing QPM Cards in the Magnum Q-Series ........................ 27

3.9.3 Removing QPM Cards............................................................... 29

4.0 OPERATION....................................................................................... 30

4.1 Switching Functionality..................................................................... 30

4.2 Status LEDs ....................................................................................... 31

4.3 Manual Switches for Up-link push-button, for RJ-45 quad-port....... 31

4.4 Auto-negotiation, for Fast Ethernet copper ports............................... 31

4.5 Auto-negotiation for 10 Mb ports, half- or full-duplex mode............ 33

4.6 Flow-control, IEEE 802.3x standard ................................................. 33

4.7 Power Budget Calculations for Quad-Series QPM’s with Fiber ....... 34

iii

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

5.0 INTRODUCTION - MAGNUM QUAD-SERIES (QPM)............... 35

5.1 Inspecting the Package and Product .................................................. 35

5.2 Product Description ........................................................................... 35

5.2.1 QPM-MST, 100Mb multi-mode FX-ST Quad-port Mod .......... 36

5.2.2 QPM-MSC 100Mbps multi-mode FX-SC Quad-port, “snap-in”37

5.2.3 QPM-SSC 100Mbps single-mode FX-SC-type, “snap-in” con. 37

5.2.4 QPM-MTRJ, 100Mb multi-mode FX Quad-Port, MTRJ small- 38

5.2.5 QPM-MV45, 100Mbps multi-mode FX Quad-Port VF45 small-38

5.2.6 QPM-RJ45 (Twisted Pair), 10/100Mb TP Quad-Port................ 39

5.2.7 QPRJ-MSC, “3 + 1” 3@10/100Mb RJ-45 and 1@100Mb Fib.. 40

5.2.8 QPRJ-MST, “3 + 1” 3@10/100Mb RJ-45 and 1@100Mb Fib.. 41

5.2.9 QPRJ-SSC, “3 + 1” 3@10/100Mb RJ-45 and 1@100Mb Fib... 41

5.2.10 QPM-FP..................................................................................... 41

6.0 TROUBLESHOOTING...................................................................... 42

6.1 Before Calling for Assistance............................................................ 42

6.2 When Calling for Assistance ............................................................. 43

6.3 Return Material Authorization (RMA) Procedure............................. 43

6.4 Shipping and Packaging Information................................................. 44

APPENDIX A: WARRANTY INFORMATION......................................... 44

APPENDIX B: MAGNUM INTERNAL DC POWER SUPPLY OPTION44

APPENDIX C: MAGNUM INTERNAL DC DUAL-SOURCE POWER.. 47

Revisions

Rev D 12/02 : Updated Appendices B and C for 100VDC (90 to 160v range) option

Rev C 06/02 : Updated the Rack Mounting and Appendix B & C with 24VDC and

125VDC Power Supply option

Rev B 04/01 : Change the company name to GarrettCom, Inc. (Formerly it was

Garrett Communications). There are no changes to the content of the material at

this time

Rev A 08/99 : This revision is the initial release of the

Magnum Quad Series Fiber

Switch

user manual.

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

The Magnum Line

ETHERNET CONNECTIVITY PRODUCTS

"DESIGNED AND MANUFACTURED IN THE USA"

OVERVIEW

GarrettCom, Inc.offers the premium-quality Magnumline of Ethernet LAN

connectivity products with industry-standard functionality and built-in fiber

configurability. Magnum products are designed for use in demanding Carrier Class,

Industrial Grade and OEM applications where reliability is a primary consideration.

6K25 Managed Fiber Switches, Gigabit, 100 and 10 Mbps, fiber and copper ports,

mix-and match. Features SFF fiber for up to 25 fiber ports in a 1U unit.

4K-Series Switches, 100 and 10 Mbps, copper ports with optional fiber port, with

auto-negotiating full switching performance.

Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports, mixed-speed

and mixed-media types, full switching performance.

P62-Series “Outdoor Ethernet Switches, for temperature uncontrolled applications

6 10/100 and 2 100Mb fiber ports, managed and unmanaged models, all fiber types.

Mixed-Media Fiber Hub, 16-port Stackable,10/100 auto-sensing

Dual Speed 8-port and 16-port Stackables, 10/100 auto-sensing

Stackable Hubs, SNMP Optional

10Mb series and 100Mb series, both w/ optional port modules

Personal Switches, 10/100Mb

8 port dual speed, Auto-negotiable with fiber option

Personal Hubs, 100Mb or 10/100Mb

8-port, with two switched ports (1 fiber built in)

Personal Hubs, 10Mb series

8-port + AUI, stackable to 5 high, + optional BNC of fiber port

8 or 9-port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.

Media Converters, 10Mb and 100Mb series, regular and Hardened with integral

DC power, all fiber media port types incl. fiber ST, SC, mm., single-mode, SFF

The “X-line” of configurable MiXed Media products:

Stackable Concentrators, SNMP optional, 13-Ports

Mini-Concentrators, 7 Ports, Repeaters, 2-Ports

Repeater Port Modules (RPMs),6 types for Ethernet media

Bridge Port Modules (BPMs), 4 types, for segment isolation

Transceivers, 10Mb series Mini-Transceivers and Coax Models June, 03

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

1.0 SPECIFICATIONS

1.1 Technical Specifications

Performance

Aggregate Filtering Rate: 2,380,800 frames/sec for 16 100Mbps ports

(for Magnum QS5116)

(all ports are wire speed) 1,190,400 frames/sec for 8 100Mbps ports

(for Magnum QS580 & QS5108)

Aggregate Forwarding Rate: (for Magnum QS Fast Ethernet ports)

(all ports are wire speed) 1,190,400 frames per second, 16-port units

595,200 frames per second, 8-port units

Data Rate: 10 Mbps and 100Mbps

Address Table Capacity: 24K node addresses, self-learning (12K on

8-port models), with address aging

Packet buffer size : 8 MB dynamic (4MB for 8-port)

Latency: 5 s + packet time (100 to 100Mbps)

15 s + packet time (10 to 10 Mbps, and 10 to 100Mbps)

Network Standards

Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,

IEEE 802.3u: 100BASE-TX, 100BASE-FX

Maximum 10 Mbps Ethernet Segment Lengths

Unshielded twisted pair - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

10BASE-FL multi-mode fiber optic - 2 km (6,562 ft)

10BASE-FL single-mode fiber optic - 10 km (32,810 ft)

Maximum Standard Fast Ethernet Segment Lengths:

10BASE-T (CAT 3, 4, 5 UTP) - 100 m (328 ft)

100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

100BASE-FX, half-duplex, multi-mode - 412 m (1350 ft)

100BASE-FX, full-duplex, multi-mode - 2.0 km (6,562 ft)

100BASE-SX, short wavelength HDX m.m. - 300 m ( 935 ft)

100BASE-FX, half-duplex, single-mode - 412 m (1350 ft)

100BASE-FX, full-duplex, single-mode - 15.0 km (49,215 ft)

Connectors for copper wiring

Twisted Pair at 10/100Mb: RJ-45 shielded, female, front mounted

(for Magnum Quad-Series Fast Ethernet copper ports, use Cat 5 cable)

Fiber Multi-mode connector types:

Fiber Port, SC-type (snap-in): Fiber optic multi-mode, 100BASE-FX

Fiber Port, ST-type (twist-lock): Fiber optic multi-mode, 100BASE-FX

Fiber Port, MTRJ-type (plug-in): Fiber optic multi-mode, 100BASE-FX

Fiber Port, VF-45 type (plug-in): Fiber optic multi-mode, 100BASE-FX

Fiber Port, ST-type (twist-lock): Fiber optic multi-mode, 10ASE-FL

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

Fiber Single-mode connector types:

Fiber Port, SC-type: Fiber optic single-mode, 100BASE-FX

Manual switch-selections and jumpers

Up-link Push-button: Crossover sw for one RJ-45 port per QPM-RJ45

Fiber default: Full-duplex (Internal jumpers may select HDX mode)

Copper default: Auto-negotiation (Internal jumpers may alternatively

select fixed 100Mb full-duplex, or fixed 100Mbps half-duplex)

LEDs: Per Port

LK: Steady ON when media link is operational

ACT: ON with receiver port activity

FDX/HDX: ON = Full-Duplex Mode

OFF = Half-Duplex Mode

100/10: ON = 100Mbps speed

OFF = 10 Mbps

Operating Environment

Ambient Temperature: 32to 120F (0to 50C)

Storage Temperature: -40to 185F (-40to 85C)

Ambient Relative Humidity: 10% to 95% (non-condensing)

Packaging

Enclosure: Rugged High strength metal. Suitable for stand-alone or rack-

mounting

Dimensions: 1.75 in H x 17.0 in W x 9.13 in D (10.0 in W for QS580)

4.45cm H x 43.2cm W x 23.2cm D (25.4 cm W for QS580)

Weight: 4.0 lb. (1.8 Kg) for rack-mount models, 2.5 lb. for table-top

Cooling method: Fan cooled, @ 9 cfm

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed at rear of chassis,

with adjacent manual ON-OFF switch (on AC models only)

Input Voltage: 110 to 240 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging)

Power Consumption: 20 watts typical (8 port model)

35 watts typical (16 port model)

Redundant power supplies available as options

DC Power Supply (Options)

-48VDC Power Input Voltage : 36 to 70 VDC

24VDC Power Input Voltage : 20 to 36VDC

125VDC Power Input Voltage : 120 to 160VDC

Std. Terminal Block : “ -, GND, + ”

Power Consumption: same as for AC models, see above

For Dual Source and Redundant DC for –48VDC, 24VDC Power &

125VDC supply options (Optional), see Appendices

For optional 23” Telco rack-mount brackets, order Model # RMB-23W

Agency Approvals

UL listed (UL1950), cUL, CE

Emissions meet FCC Part 15 Class A

Warranty Three years, return to factory Made in USA

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

1.2 Ordering Information

Magnum Quad-Series Fiber Switches

MODEL DESCRIPTION

Magnum QS580 8-port 10/100 Switch, holds up to 2 Quad-port Modules

with 4 switched ports each. Shelf or table-top mounting.

For mixed-media flexibility, combinations of RJ-45 and

various fiber port connector types, modes, and speeds can

be configured. Full speed filtering and forwarding at

100Mbps speed across all ports, self-learning 12K-node

address table, and large 4MB packet buffers. Front-

mounted LEDs, internal auto-ranging power supply

Magnum QS5108 Same as Model QS580 Switch, but in a 19” rack-mount

package, with mounting brackets.

Magnum QS5116 Same as Model QS5108, but with 24K-node address table

and 8MB packet buffers. Holds up to 4 Quad-port Modules

(QPMs), 19” rack-mount package, with mounting brackets.

Magnum Quad-Series Port Modules

QPM-MSC Fiber module for Quad-Series Switches, with four

100Mbps multi-mode FX SC connectors

QPM-MST Fiber module for Quad-Series Switches, with four

100Mbps multi-mode FX ST connectors

QPM-SSC Fiber module for Quad-Series Switches, with four

100Mbps single-mode FX SC connectors

QPM-MV45 Fiber module for Quad-Series Switches, with four

100Mbps multi-mode FX “VF-45” connectors

QPM-MTRJ Fiber module for Quad-Series Switches, with four

100Mbps multi-mode FX “MTRJ” connectors

QPM-RJ45 RJ-45 module for Quad-Series Switches, with four

100Mbps auto-negotiating RJ-45 ports, one of which has

an up-link push-button

QPRJ-MSC 3TP+1F “3+1 combo” module for Quad-Series Switches,

with three 10/100MB auto-negotiating RJ-45 ports and one

fiber port with 100Mbps multi-mode FX SC connector

QPRJ-MST 3TP+1F “3+1 combo” module, same as QPRJ-MSC but

with fiber ST-type connector

QPRJ-SSC 3TP+1F “3+1 combo” module, same as QPRJ-MSC but

with fiber single-mode FX SC connector

QPM10-FST Fiber module for Quad-Series Switches, with four 10 Mbps

multi-mode FL ST-type connectors

GarrettCom, Incl. reserves the right to change specifications, performance

characteristics and/or model offerings without notice.

www GarrettCom com

Magnum Quad-Series Fiber Switches Installation and User Guide (06/03)

2.0 INTRODUCTION

2.1 Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this

product; notify the carrier of any damage that you believe occurred during shipment or

delivery. Inspect the contents of this package for any signs of damage and ensure that

the items listed below are included.

This package should contain:

1 Magnum QS580, QS5108 or QS5116 Fiber Switches

1 AC Power Cord (U.S. and other 115 VAC only)

1 Set of two wall-mounting brackets (for QS580 Model only)

1 Set of metal “Ears” for optional “19” rack mounting (for QS5108 &

QS5116 only)

1 Installation and User Guide (this manual)

1 Product Registration Card

Remove the items from the shipping container. Be sure to keep the shipping

container should you need to re-ship the unit at a later date. To validate the product

warranty, please complete and return the enclosed Product Registration Card to

GarrettCom, Inc. as soon as possible.

In the event there are items missing or damaged, contact the party from whom

you purchased the product. If the unit needs to be returned, please use the original

shipping container if possible. Refer to Section 6, Troubleshooting, for specific return

procedures.

www GarrettCom com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GarrettCom Interruttore

GarrettCom

GarrettCom Magnum CS14 Series Manuale utente

GarrettCom

GarrettCom Magnum 6KQ Manuale utente

GarrettCom

GarrettCom Magnum 6K16V Manuale utente

GarrettCom

GarrettCom Magnum 6K32 Manuale utente

GarrettCom

GarrettCom Magnum 4K220 Manuale utente

GarrettCom

GarrettCom Magnum 6K32T Istruzioni per l’uso

GarrettCom

GarrettCom Magnum PS14P Manuale utente

GarrettCom

GarrettCom Magnum 6K25 Manuale utente

GarrettCom

GarrettCom Magnum DS 880 Manuale utente

GarrettCom

GarrettCom MAGNUM 6KM Manuale utente

GarrettCom

GarrettCom Magnum 1016 Manuale utente

GarrettCom

GarrettCom magnum 6kl Manuale utente

GarrettCom

GarrettCom Magnum CSG14 Manuale utente

GarrettCom

GarrettCom Magnum ITS Blade Manuale utente

GarrettCom

GarrettCom Magnum 6KQE Manuale utente

GarrettCom

GarrettCom PS14H-48VDC Manuale utente

GarrettCom

GarrettCom DS80C Manuale utente

GarrettCom

GarrettCom Quad Manuale utente

GarrettCom

GarrettCom Magnum 6K32F Manuale utente

GarrettCom

GarrettCom Magnum ST80 Stackable Manuale utente

GarrettCom

GarrettCom Magnum 6K32F Manuale utente

GarrettCom

GarrettCom 4K-Series Manuale utente

GarrettCom

GarrettCom Magnum 6K8 Manuale utente

GarrettCom

GarrettCom MAGNUM MAGNUM 6KM Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente