Gate WARFET Manuale utente

Last update on December 22, 2016 www.gatee.eu

USER GUIDE

WARFET

GATE Menet, Wojtak Sp. J. does not take any responsibility for damages, injuries

and accidents resulting in the use of this product or the use of Air Electric Gun

with the product installed.

Information contained in this document is subject to updating without notice.

You should program your WARFET before the first use.

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE INSTALLING THE DEVICE

THE DEVICE COVER MUST NOT BE REMOVED BY THE USER

Caution must be exercised to prevent short circuiting the battery as the

consequences can be very dangerous.

We recommend that this product should be installed by an experienced airsoft

service.

Notice

Safety Summary

DANGER!

FOR YOUR SAFETY

USER GUIDE

02 WWW.GATEE.EU

WARFET

CERTIFICATE OF CONFORMITY

The symbol shown here means that the product is classed as Electrical or Electronic Equipment

and should not be disposed with other household and commercial waste at the end of its

working life. The Waste of Electrical and Electronic Equipment (WEEE Directive 2012/19/UE)

has been put in place to recycle products using best available recovery and recycling

techniques to minimize the impact on the environment. Purchasers shall take any old electrical

equipment to waste recycling public centers or points of sale.

PRODUCT DISPOSAL INSTRUCTIONS

GATE Menet, Wojtak Sp. J. hereby declares under our sole responsibility that the product

GATE WARFET is in conformity with the essential requirements of the following Directives:

EC DIRECTIVE 2011/65/EU

This product has been certified as RoHS Compliant.

WARNING:

NOTE:

Before starting installation process, please ensure that your AEG is

empty and there are no BBs inside.

Always use a fuse between the battery and the Power Module.

Incorrectly connecting positive and negative battery terminals will

cause immediate damage to the unit and it can lead to fire.

Please check if you have downloaded the latest manual from the Technical Support

section of our website: www.gatee.eu. The Product Warranty Form is also

available there.

In case you have any difficulties while installing or using this product, we

recommend to email us at [email protected].

WWW.GATEE.EU

USER GUIDE WARFET

Table of Contents:

Safety Summary ..............................................................................................................2

Table of Contents .............................................................................................................4

01. Overview ....................................................................................................................5

• WARFET Features ............................................................................................5

• WARFET Power Module parameters .............................................................6

• Tactical Programming Card description ..................................................................6

• Tactical Programming Card parameters ..................................................................7

• Key functions .............................................................................................................8

• Package contents ....................................................................................................13

02. Plug & Play Installation ............................................................................................14

03. Hardwired Installation .............................................................................................16

• Switch mode ............................................................................................................16

• AEG standard installation .......................................................................................16

• Installation of WARFET Power Module without replacement of wires .....16

• Installation of WARFET Power Module with replacement of wires ...........17

04. Set up your WARFET Power Module with Tactical Programming Card ............18

05. Pre-cocking Boost adjustment ...............................................................................20

06. Troubleshooting ......................................................................................................22

07. GATE Limited Warranty Policy ...............................................................................24

USER GUIDE

04 WWW.GATEE.EU

WARFET

WARFET Features

WARFET is GATE's most advanced AEG Control System. It has 20 functions and

almost 6 million possible configurations. The outstanding Tactical Programming

Card provides you with very easy access to the WARFET Power Module settings.

Thanks to the Pre-cocking and Smart Trigger functions, you can achieve a trigger

response similar to a real gun. The Programmable Burst (1-5 rounds) enables you to

fire a pre-determined number of BBs, which is very useful in MILSLIM and for using

low-caps. Another function is ROF Control, which allows you to reduce ROF, so you

can use strong LiPo batteries, and still have ROF just like in a real rifle. If your AEG

becomes jammed, the Smart Fuse protects the battery and the motor against

damage. It also prevents deep battery drain. Moreover, with WARFET you get:

MOSFET, ON/OFF Active Brake, Built-in self-test, Debouncing, and more. Many

useful functions, great electrical specifications and conformal coating (military

specifications: MIL-V-173C) make the AEG Control System able to meet the needs

of most experienced airsoft players.

SUPER-EASY INSTALLATION - JUST PLUG&PLAY, NO SOLDERING REQUIRED

• User-friendly configuration via the Tactical Programming Card

• Sturdy and super-small size WARFET Power Module

• Compatibility with the strongest AEG replicas and batteries (ready to work with

LiPo 14.8V, 5000 mAh, 60C)

• Tested with car batteries

• Super-easy installation - thanks to the Mini Tamiya adapters, you can connect

WARFET to the original (stock) wiring

• It can work with most built-in MOSFETs

• With stock wiring, WARFET reduces melting switch assemblies

01. Overview

WWW.GATEE.EU

USER GUIDE WARFET

WARFET Power Module parameters

• In hardwired installation, WARFET draws the energy from the battery directly

to the motor, bypassing the mechanical trigger contacts

• Resistant to atmospheric conditions (military specifications: MIL-V-173C)

• Deep-drain protection for 7.4V, 11.1V, 14.8V LiPoly and 9.6V, 12.8V LiFePO4

• Improves battery life, ROF, spring life and gearbox reliability

The outstanding Tactical Programming Card provides you with very easy access to

the WARFET Power Module settings. All you need to do is to connect the Tactical

Programming Card between the battery and the Power Module. A big advantage is

that there is no need to use any additional wires. The WARFET Power Module can

be fitted out of view in your AEG, and you still have easy access to its settings. The

Tactical Programming Card communicates with the WARFET Power Module and

displays the most recently saved settings. You can simply change them using three

buttons.

Wide range of supply voltage:

Protection against short-circuits:

Incredibly low current consumption on stand-by:

Ultra-low resistance:

Dimensions:

Weight:

3-17V

up to 1000A

0.2mA

2mΩ

56x20x9mm

9.4g

Tactical Programming Card description

USER GUIDE

06 WWW.GATEE.EU

WARFET

Tactical Programming Card parameters

Supply voltage:

Dimensions:

Weight:

Number of LEDs:

Number of buttons:

5-17V

67x53x7mm

27.3g

WWW.GATEE.EU

USER GUIDE WARFET

Key Functions

The outstanding Tactical Programming Card provides you with very

easy access to the Power Module settings. All you need to do is

connect the Tactical Programming Card between the battery and the

Power Module.

Tactical Programming Card

Victory in the game is often a matter of fractions of seconds. Thanks to

the PRE-COCKING, you gain a trigger reaction similar to a real gun. It

allows for initial spring compression, which speeds up the trigger

response significantly. You can set the time of PRE-COCKING using the

Tactical Programming Card. There are two PRE-COCKING MODES:

1) AUTO MODE – the spring is automatically compressed after each

shot,

2) TRIGGER MODE – the first trigger action compresses the spring, and

the second trigger action fires the shot.

Pre-Cocking

Super-easy installation, just plug and play. No soldering required. All

you need to do is connect the battery and the rifle to the Power

Module.

PLUG&PLAY

The burst enables you to shoot a pre-determined number of BBs (1-5

rounds), which is very useful in MILSLIM and when using low-caps.

You can transform AUTO MODE to BURST MODE or SEMI MODE to

BURST MODE*. The Tactical Programming Card allows you to set the

burst time. The Power Module automatically corrects the burst time

according to the voltage level of the battery.

Programmable Burst

USER GUIDE

08 WWW.GATEE.EU

WARFET

Please note: using PRE-COCKING increases wear and tear on the

gearbox. PRE-COCKING is designed for SEMI mode. In the AUTO mode,

it can result in blank shots.

*SEMI to BURST in modified installations only.

Burst mode enables you to make 3-shot series. In this way you can

save ammunition and increase the realism. You can change AUTO

mode to BURST mode or SEMI* mode to BURST mode.

If in SAFE/SEMI/BURST mode you release the trigger earlier, you can

make one or two shots. The burst time is set in the menu with accuracy

to 4ms. The processor actively compensates for the change in burst

time with a decrease in the rate of fire due to battery discharging.

3-rd burst

The function gives you the option to program your fire selector.

There are five modes:

Configurable Fire Selector

This ensures there is no loss of the rifle’s rate of fire, so you can use

stronger LiPo batteries, and still have ROF just like in a real gun.

Rate Of Fire Control

We know how vital the fast trigger response is during combat. This is

why we have developed the Smart Trigger function. It enables you to

achieve a faster trigger response. It works with the ROF Control

system. During the first shot, the microprocessor sets the ROF Control

to 100%. After the first shot, it switches to a previously programmed

value (e.g. 50%). As a consequence, the first shot is fired at a full rate of

fire, and subsequent shots at a reduced ROF. The best results can be

achieved by using a battery with a higher than standard voltage. For

example, if you use a 7.4V battery, you can replace it with 11.1V. In this

way, you will achieve a faster trigger response with the same rate of

fire as with a standard battery. The Smart Trigger is most effective

when the Burst time is set at 3 rounds.

Smart Trigger

WWW.GATEE.EU

USER GUIDE WARFET

- STOCK WIRING SEMI/AUTO

- STOCK WIRING SEMI/BURST

- MODIFIED WIRING SEMI/AUTO

- MODIFIED WIRING SEMI/BURST

- MODIFIED WIRING BURST/AUTO

*SEMI to BURST in enhanced mode only

Battery Protection

Protection against Over-Discharge of the Battery. Modern LiPo and

LiFe batteries are very sensitive to over-discharge. If you do not want

to damage the battery and you care about its service life, this

protection is indispensable. The microprocessor monitors the battery

voltage constantly. When the voltage drops down to a critical level,

the Power Module will not allow firing.

Smart Fuse

We have developed an electronic fuse with an accurate current

sensor. A combination of current, voltage and temperature

measurements makes your AEG installation highly reliable. It protects

the MOSFET against overheating, overloading and short-circuiting. If

your airsoft gun becomes jammed, the function protects the motor

and battery against damage.

We know how important reliability is on the battlefield. That's why the

unit has thermal protection. In tandem with a time-lag fuse, it fully

protects your AEG installation.

Electronic Fuse

The provides you with the opportunity to decide if you

want to use the Active Brake function. If you do not need this, you can

turn it off easily. It will lead to improving the lifespan of your motor.

Power Module

ON/OFF Active Brake

Do you care about realism? Would you like to increase the life of the

gearbox? Does your rifle have such a high rate of fire that you are not

able to make a single shot? The Active Brake sorts things out. In SEMI

Mode, the brake does not allow for compressing a piston after a shot.

The piston will stop in the front position which eliminates

unnecessary stresses, increasing the service life of the gearbox and its

parts. This is important, especially with an AEG power upgrade. After

releasing the trigger, the rifle immediately stops firing. So, you gain

more realism and, additionally, you do not waste your precious

ammunition.

Active Brake

USER GUIDE

10 WWW.GATEE.EU

WARFET

Altri manuali per WARFET

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Gate Sistema di controllo

Gate

Gate Titan Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente