Gator GRV43SKT Manuale utente

USER MANUAL

GRV43SKT

gatordriverassist.com

For more information

on the Gator range

go to our website

Monitor, Monitor power cable, Number plate mount wireless camera,

USB to DC camera charging cable, Number plate mount adaptor,

Dash mount, Suction mount, Vent mount & Mounting screws

Introduction

Product features & specifications

Monitor

• 4.3” High-resolution LCD Screen

• Resolution 480 x 272 Pixels

• Parking guide lines

• 12-30V Compatible

• 3.5M Monitor power cable

• Power cable fuse: 3A

• Operation Current: <150mA

• Dimensions 90(H) x 125(W) x 44mm(L)

Camera

• Pixels 640 x 480

• Lens angle H135° / V90° /D165°

• IP-67 Dust and water protection

• Solar Charging Power: 0.8 W

• 1/3” CMOS Sensor

• Image quality Max 30 FPS

• Solar Energy Conversion Rate: 23%

• Battery Capacity: 2100 mAh

Transmitter

• Frequency: 2400 - 2485.5 MHz

• Transmission distance: 17.5 meters max.

• Working Temperature: 14"- 140"F (-10·- 60"C)

• Working Voltage: 12-30V

Thank you for purchasing the Gator GRV43SKT 4.3” wireless

solar powered reverse camera kit. Please ensure that you have

read the product manual and instructions in full, prior to

installation and use. Failure to do so may result in product

failure/damage or incorrect operation and therefore impact the

product performance.

Introduction..................................................................2

Product features & specifications..........................................2

Table of contents..................................................................3

Inclusions.............................................................................4

Charging the Camera's built-in battery.................................5

Monitor Installation...............................................................6

Installing the camera...........................................................8

Adjusting the camera angle..................................................9

Operating your device.........................................................9

Menu options and settings................................................10

Troubleshooting guide.......................................................13

Safety information & warnings...........................................14

Technical assistance..........................................................15

Table of contents

Inclusions

Monitor

Adapter Plate

Camera

Monitor

Suction Mount

Monitor

Vent Mount

Monitor

Adhesive Mount

Charging Cable

Monitor Power Cable

Charging the Camera's built-in battery

1. Connect the supplied DC cord to the charging port of the

camera by removing the end plate cover on the camera.

Carefully slide up away from the camera plate.

2. Plug the cable USB port into any standard USB charging

adapter (Not included) with an output rating more than 1000mA

3. A red light indicator near the camera cover will illuminate while

charging.

4. Charge time takes 4 to 5 hours. Once fully charged the

indicator light will turn off.

Under normal use, the camera maintains a charge with exposure

to sunlight. A battery status indicator is provided on the monitor

when the camera is in use. If you're storing your vehicle in a

garage (or not exposing the camera to sunlight on a regular

basis) you may need to recharge it via the DC port.

NOTE:

* Prior to installation the camera must be fully charged.

USB port

End plate

DC port

Indicator light

1. There are three ways you can mount the monitor, either

suction, vent or the adhesive mount.

With the suction mount the monitor can be mounted

to the windscreen or dash and be easily removed.

Attach the suction mount to the back of the monitor

using the supplied screwdriver and threaded screw.

Pay attention to orientation see pictures below.

With the suction lever in the released position,

press the suction cup against the windshield. Press the suction

lever toward the suction cup to lock the mount. To adjust the

angle of monitor, loosen the collar on the ball joint, re-tighten in

the desired position.

The adhesive mount can be used to permanently fix

the monitor to the dash. Attach the adhesive mount

to the back of the monitor using the supplied

screwdriver and threaded screw. For good

adhesion thoroughly clean the dash or windscreen

before mounting.

Monitor Installation

Screw Align

Rotate and Lock

Monitor Installation

For the vent mount, screw the socket adapter to the

back of the monitor with the supplied screwdriver

and small screw. Then secure the ball end of vent

mount to the socket and tighten the retaining nut.

Lift the clamp up and down to secure or release the

vent clip on the vent.

2. Connect the monitor power cable to the monitor and plug the

socket end into your 12-30V accessory input.

Vent Screw

Align

Connect

Rotate to tighten Lock & release

Ball Nut Vent Mount

Installing the camera

1. Identify the number plate size you have. This will determine if

you need to use the adapter plate.

2. If you need to use the adapter plate this slides inside the back

of the camera base plate

3. Mount your number plate to the camera plate using your

existing screws, by screwing into existing mounting holes on your

vehicle. Alternatively use the extra screws provided.

Slimline

Numberplate

Mount

Light illuminates

when active

Standard Size

Numberplate Adaptor

Wireless Solar

Powered Rear Camera

Adjusting the camera angle

1. When you want to adjust the camera angle, firstly make sure

the monitor is powered, by pressing the "Touch For Rearview"

button to enter working status.

2. Please note when rotating the camera, hold the license base

plate with one hand, hold the camera outer frame with the other

hand, then move up or down to adjust the angle.

Operating your device

1. Switch your 12-volt DC power port on with your ignition, the

monitor will start work accordingly, the video signal will be sent

from camera and will be displayed on the monitor.

The image is set to time out after 45 seconds (default). However

if you wish to shut the image off manually, just touch the 'Touch

for Rearview" Button on the monitor again anytime to stop at

once.

2. If you want to see the rearview image when driving your car ,

just touch the 'Touch For Rearview" Button on the top of

monitor.

3. When the vehicle is shut off, power is removed from the

monitor and the monitor will shut off automatically, and the

camera will stop working.

4. When the camera is active the light to the right on the camera

will illuminate

Menu options and settings

1. The middle button [MENU/OK]:

Short Press to enter monitor menu settings.

Long Press (press and hold for 3 seconds) to confirm the chosen

item in the menu setting interface.

2. The Up button [ADD]:

Short Press to change/add parameter value in the menu setting

interface.

3. The Down button [DEC]:

Short Press to change/decrease parameter value in the menu

setting interface.

( )

Indice

Altri manuali Gator Telecamera da cruscotto

Manuali Telecamera da cruscotto popolari di altre marche

Cansonic

Cansonic UltraDuo Z2 Manuale utente

Gazer

Gazer F720 Manuale utente

HP f500g Manuale utente

Xblitz

Xblitz TANGO 4K Manuale utente

Rexing

Rexing M1 Manuale utente

Maka Technologies

Maka Technologies Marbella MXPro Manuale utente

NESA

NESA NRC-80DLM Istruzioni per l'installazione e il funzionamento

Kaiser Baas

Kaiser Baas R20 Manuale utente

Boyo

Boyo VTM43TC Manuale utente

Minolta

Minolta MNCD37 Manuale utente

Thinkware

Thinkware FA10 Manuale utente

Momento

Momento MD-5200 Manuale utente

BlackVue

BlackVue DR590X-1CH Manuale utente

HP F300 Manuale utente

CammSys

CammSys BlackSys BH-300 Manuale utente

Snooper

Snooper DVR-2HD Manuale utente

Lukas

Lukas Q900 Manuale utente

RVS

RVS 450C Manuale utente