GDC SR-1000 STANDALONE INTEGRATED MEDIA BLOCK Manuale utente
INSTALLATION MANUAL FOR
SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
(For use with Series 1 Projectors)
Version 7.90
February 15th, 2023
- 1 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
TABLE OF CONTENTS
Table of Contents
1Introduction ............................................................................... 4
1.1 Physical, Environmental and Power Requirements......................5
2Packing List ............................................................................... 6
3Hardware Installation and Setup .............................................. 8
3.1 Installing the HDDs ..........................................................................8
3.2 Installing the SR-1000 IMB ............................................................10
3.3 Connecting the IMB to a Series 1 Projector.................................17
3.4 Powering up the SR-1000 IMB with S1 Kit Plus...........................18
4Projector Configuration in SDI Mode ..................................... 19
5Supported Playback Formats ................................................. 20
6Converting SR-1000 from SDI Mode to IMB Mode................. 20
- 2 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
Thank you for purchasing a GDC SR-1000 Integrated Media Block™with S1 Kit Plus from
GDC Technology Limited.
To ensure proper operation and to maximize value of the SR-1000 Integrated Media Block™with S1 Kit Plus, please
review this Installation Manual. It will guide you through all the features and benefits of the new SR-1000 Integrated Media
Block™with S1 Kit Plus.
COPYRIGHT NOTICE
Copyright © 2023 by GDC Technology Limited. All Rights Reserved.
No part of this manual may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any
human or computer language, in a form or by any means, electronic, mechanical, photocopying, recording, magnetic, optical,
manual or otherwise, or disclosed to third parties without prior written permission of GDC Technology Limited.
MANUAL DISCLAIMER
This manual is made with version 7.90 and there might be slight differences depending on the software version the Media Block
is running. The contents, features and specifications stated in this manual are subject to change without notice due to continuous
product development and improvements. In no other event shall GDC Technology Limited be liable for any loss of profit or any
other commercial damages, including but not limited to special, consequential, or other damages.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
- 4 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
1. Introduction
1 Introduction
This manual serves as a guide for setting up an SR-1000 Integrated Media Block™with S1 Kit Plus
and installing it with a Series 1 DLP Cinema Projector. It consists of a metal chassis (as shown in
Figure 1) and the SR-1000 IMB with its faceplate (as shown in Figure 2). The faceplate has two BNC
connectors for HD-SDI connections to a Series 1 Projector.
Figure 1: Metal Chassis
Figure 2: SR-1000 IMB with HD-SDI Connectors
Note: Users of the SR-1000 Integrated Media Block™with S1 Kit Plus should
refer to the SR-1000 Installation and User Manuals before using this document.
- 5 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
1. Introduction
1.1 Physical, Environmental and Power Requirements
•Physical:
▪Dimensions –482.6 (W) x 454.3 (D) x 133.5 (H) mm
▪Weight (including SR-1000 IMB) –15.7kg
•Environmental:
▪Operating Temperature –0°C to 40°C (32°F to 104°F)
▪Operating Humidity –20% to 90%, non-condensing
▪Operating Altitude –10,000ft. (3,000m) above sea level
•Power:
▪Input –100 to 240V, 63 to 47Hz, 2/4.5A
- 6 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
2. Packing List
2 Packing List
Contents of the SR-1000 IMB with S1 Kit Plus package are as listed below:
Sr.No.
Description
Quantity
Actual Photograph
1
Metal Chassis
1
2
SR-1000 IMB
1
3
3.5” SATA HDD
with HDD Tray
3
4
eSATA Cable
(1M, Male-to-Male)
1
5
Coaxial Cables
(10M, Green and Black)
2
- 7 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
2. Packing List
6
International Standard
Power Cord (1.5M)
1
7
HDD Tray Key
1
8
RJ45 AES Audio Cable
1#
9
RJ45 GPIO Cables
2#
10
Network Cable
1
11
RJ45 to DB25 Audio
Converter
1#
12
Cable Holder Clip
for eSATA
2
13
Spare Screws for Front Plate (2 nos.)
#Subject to actual configuration. Please specify with GDC sales representative.
- 8 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
3. Hardware Installation and Setup
3 Hardware Installation and Setup
3.1 Installing the HDDs
The front panel of the S1 Kit Plus chassis houses the slot for the SR-1000 IMB along with the
RAID bay slots for HDDs, LED indicator array (for the RAID, Fan and Power) and a Power switch,
as shown in Figure 3.
Figure 3: Front Panel of S1 Kit Plus chassis
To insert an HDD into the S1 Kit Plus chassis, make sure that the HDD tray handle is in open
position, as shown in Figure 4. Insert the HDD tray into an open slot on the unit and gently push
the tray until it is fully inserted into the HDD slot.
Figure 4: Insert HDD into chassis
- 9 -
February 15th, 2023
GDC SR-1000 INTEGRATED MEDIA BLOCK™WITH S1 KIT PLUS
INSTALLATION MANUAL
3. Hardware Installation and Setup
Once the HDD Tray is fully inserted into the drive slot, close the tray handle by pushing it in, as
shown in Figure 5. Repeat these steps to insert the other two HDDs into the chassis as well.
Figure 5: Close Tray Handle
Insert the Tray Key into the key slot of the HDD Tray and turn it counter-clockwise to lock the
HDD tray in place, as shown in Figure 6.
Figure 6: Lock HDD using Tray Key
Altri manuali per SR-1000 STANDALONE INTEGRATED MEDIA BLOCK
6
Indice
Altri manuali GDC Sistema di controllo
