GE 25993 Manuale utente
Low-Profile HD
Amplified Antenna
User’s Manual
25993 v1
02/02/15 RT
1
Introduction:
The Low-Profile HD Amplified Antenna is specially
designed to receive digital and analog terrestrial
broadcasted TV signals. The compact and stylish
design will blend in with any décor.
Important Safety Instructions:
•Use only the supplied UL-listed power adapter
•This antenna is for indoor use only
•Do not install in wet locations or
locations that can get wet
Features:
•VHF/UHF/HDTV
•Impedance 75 Ohm
•Low noise USB-powered amplifier
•Stylish slim profile
Package Contents:
•Digital indoor antenna
•Antenna stand
•In-line low noise USB-powered amplifier
•Micro USB cable
•UL-listed power adapter
•Users manual
•Wall mounting hardware
Antenna
StandDigital Indoor Antenna
2
Wall Mounting
For best reception, you will likely want to mount
the antenna above your television. Please follow
the instructions below for proper wall mounting.
1. Locate the mounting hardware
2. Locate the tools below (tools not included)
a. Some tools you will need are:
i. Tape measure
ii. Pencil or pen to mark your holes
iii. 1/8” drill bit and drill
iv. Hammer
v. Phillips screwdriver
3. Identify where you want to mount the antenna
4. Use your tape measure and a pencil, mark
two places on the wall exactly 7 inches apart
(as shown on the back of your antenna)
USB adapterMicro USB cable
Mounting hardware Users manual Power Amplifier
3
5. Use a 1/8" drill bit and carefully drill
the two holes marked in step 4.
6. Use your hammer and lightly tap in
the supplied drywall anchors until
they are flush with receptacle.
7. Use your Phillips screwdriver. Screw in
the screws provided until they
stick out about 1/16".
8. Mount the antenna onto the screws by
lining up the keyhole slots on the back
of the antenna with the screws.
Be sure you have routed the coax cable in the
direction you want the cable to go by using the
cable channel on the bottom of the antenna.
Installation:
1. Attach the coax cable from the antenna
to the power amplifier “Antenna”
2. Connect the attached coax
cable from the amplifier labeled
“Receiver” to the back of the TV
3. For televisions equipped with USB ports:
Connect the supplied USB cable to the USB
port on the amplifier, then connect the
other end to your television’s USB port.
For televisions without USB ports:
Connect the supplied USB cable to the USB
port on the amplifier, then connect the
other end to the supplied AC adapter. Plug
the AC adapter into an available outlet.
4. Turn on your TV
5. Scan for your local TV channels following the
instructions found in your TV’s users manual
4
For televisions equipped with USB ports:
For televisions without USB ports:
5
Made in China
GE is a trademark of the General Electric Company
and is under license by Jasco Products Company LLC,
10 E. Memorial Road, Oklahoma City, OK 73114.
This Jasco product comes with a limited lifetime warranty.
Visit www.jascoproducts.com for details.
Questions? Contact us at 1-800-654-8483
between 7:30AM—5:00PM CST.
Antenna helpful tips
Maximize the number of channels you receive by
placing the antenna in several different locations
to see which location provides the best reception
and the maximum number of channels. Be sure
to run a new channel scan on your TV in each
position. Refer to the instruction manual that came
with your TV if you are not sure how to do this.
Position or mount the antenna as high as possible
or near a window for best performance.
Connect the antenna to your TV using the
amplifier provided as described in the installation
section. This will enhance reception for most
users. However, depending on your location and
signal environment, the antenna may work best
without the amplifier. If you are having trouble with
reception, you may try removing the amplifier and
connecting the antenna directly to the TV.
Visit www.antennaweb.org or www.dtv.gov and
look for the DTV Reception Maps to determine the
available television stations and location of the
broadcast towers in your area.
FOR FURTHER ASSISTANCE CALL,
(800) 654-8483 FOR TECHNICAL SUPPORT.
Antena amplificada
HD de bajo perfil
Manual del usuario
25993
7
Introducción:
La antena amplificada HD de bajo perfil está
diseñada especialmente para recibir señales de
difusión televisiva terrestre tanto digital como
analógica. El elegante y compacto diseño quedará
bien con cualquier estilo de decoración.
Medidas de seguridad importantes:
•Solo use el adaptador de corriente
homologado por UL provisto.
•Esta antena es solo para uso en interiores.
•No instale esta antena en lugares
húmedos o expuestos a la humedad
Características:
•VHF/UHF/HDTV
•Impedancia: 75 Ohm
•Amplificador de bajo ruido con
alimentación por USB
•Diseño delgado y moderno
Contenido del paquete:
• Antena digital para interiores
• Base para la antena
• Amplificador en línea de bajo ruido
con alimentación por USB
• Cable micro USB
• Adaptador de corriente homologado por UL
• Manual del usuario
• Accesorios para el montaje en la pared
8
Montaje en la pared
Para obtener la mejor recepción, le conviene
instalar la antena por encima del televisor. Siga las
siguientes instrucciones de montaje de la antena
para instalarla en la pared correctamente.
1. Localice los accesorios de montaje.
2. Busque las herramientas abajo especificadas
(las herramientas no se incluyen).
a. Algunas de las herramientas que
necesitará son las siguientes:
Base para
la antenaAntena digital para interiores
Adaptador USBCable micro USB
Artículos de ferretería
para el montaje
Manual del
usuario
Amplificador
de potencia
9
i. Cinta métrica
ii. Lápiz o lapicero para marcar el lugar en
donde hará los orificios
iii. Broca de 1/8” (3,5 mm) y taladro
iv. Martillo
v. Destornillador Phillips
3. Identifique el lugar en dónde
desea instalar la antena.
4. Use la cinta métrica y un lápiz, marque
dos puntos en la pared a 7 pulgadas
de distancia (como se muestra en la
parte posterior de la antena).
5. Use una broca de 1/8” y cuidadosamente haga
los dos agujeros que marcó en el paso 4.
6. Con el martillo coloque los anclajes para
pared de yeso provistos hasta que queden
al ras del tomacorriente de pared.
7. Use el destornillador Phillips. Atornille los tornillos
provistos hasta que queden a 1/16” de la pared.
8. Para instalar la antena, alinee las ranuras en la
parte posterior de la antena con los tornillos.
Asegúrese de que el cable coaxial haya quedado
en la dirección deseada utilizando el canal
de cable en la parte inferior de la antena.
Instalación:
1. Attach the coax cable from the antenna
to the power amplifier “Antenna”
1. Conecte el cable coaxial de la antena a la
“Antena” amplificadora de potencia.
2. Conecte el cable coaxial del amplificador
con la etiqueta “Receiver” a la
parte posterior del televisor.
Indice
Lingue:
Altri manuali GE Antenna
GE
GE 26438 Manuale utente
GE
GE 29884 Manuale utente
GE
GE Quantum Amplified Quantum Antenna Manuale utente
GE
GE 33691 ultra-flat digital amplified antenna Manuale utente
GE
GE 14846 Manuale utente
GE
GE 14845 Manuale utente
GE
GE TV 24769 Manuale utente
GE
GE 24763 Manuale utente
GE
GE 34137 Manuale utente
GE
GE 43452 Manuale utente
Manuali Antenna popolari di altre marche
Alfa Network
Alfa Network APA-L01 Manuale utente
Naval
Naval PR-422CA Manuale utente
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuale utente
TERK Technologies
TERK Technologies TV44 Manuale utente
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuale utente
HP
HP J8999A Manuale utente
