GE 26438 Manuale utente
26438
Foldable HD
Amplified Antenna Bar
User’s Manual
26438 v1
04/24/15 PM
1
Digital Indoor Antenna
Introduction:
The 26438 foldable HD Amplified Antenna is
specially designed to receive digital and analog
terrestrial broadcasted TV signals. The compact
and stylish design will blend in with any décor.
Important Safety Instructions:
• Use only the supplied UL-listed
power adapter
• This antenna is for indoor use only
• Do not install in wet locations or
locations that can get wet
Features:
•VHF/UHF/HDTV
• Impedance 75 Ohm
• Low noise USB-powered amplifier
• Stylish slim profile
Package Contents:
•Digital indoor antenna
•UL-listed power adapter
•Micro USB cable
•Antenna stand
UL-listed
power adapter
Micro
USB cable
Antenna stand
2
Wall Mounting
For best reception, you will likely want to mount
the antenna above your television. Please follow
the instructions below for proper wall mounting.
1. Locate the mounting hardware
2. Locate the tools below (tools not included)
a. Some tools you will need are:
i. Tape measure
ii. Pencil or pen to mark your holes
iii. 1/8” drill bit and drill
iv. Hammer
v. Phillips screwdriver
3. Identify where you want to
mount the antenna
4. Use your tape measure and a
pencil, mark two places on the
wall exactly 1.5 inches apart
5. Use a 1/8" drill bit and carefully drill
the two holes marked in step 4
•Wall mount bracket
•Users manual
•In-line low noise USB
powered amplifier
Wall mount bracket Users manual
In-line low noise
USB-powered
amplifier
6. Use your hammer and lightly tap in
the supplied drywall anchors until
they are flush with receptacle.
7. Use your Phillips screwdriver. Screw in
the screws provided until they
stick out about 1/16".
8. Mount the antenna onto the screws
by lining up the keyhole slots on the
back of the antenna with the screws.
Be sure you have routed the coax
cable in the direction you want the
cable to go by using the cable channel
on the bottom of the antenna.
Installation:
1. Attach the coax cable from the antenna
to the power amplifier “ANT IN”
2. Connect the attached coax cable
from the amplifier labeled “TO
TV” to the back of the TV
3. For televisions equipped with USB ports:
Connect the supplied USB cable to the USB
port on the amplifier, then connect the
other end to your television’s USB port.
For televisions without USB ports:
Connect the supplied USB cable to the USB
port on the amplifier, then connect the
other end to the supplied AC adapter. Plug
the AC adapter into an available outlet.
4
4. Turn on your TV
5. Scan for your local TV channels following the
instructions found in your TV’s users manual
For televisions equipped with USB ports:
For televisions without USB ports:
5
Made in China
GE is a trademark of the General Electric Company
and is under license by Jasco Products Company LLC,
10 E. Memorial Road, Oklahoma City, OK 73114.
This Jasco product comes with a limited lifetime warranty.
Visit www.jascoproducts.com for details.
Questions? Contact us at 1-800-654-8483
between 7:30AM—5:00PM CST.
FOR FURTHER ASSISTANCE CALL,
(800) 654-8483 FOR TECHNICAL SUPPORT.
Helpful Antenna Tips
Maximize the number of channels you receive by
placing the antenna in several different locations
to see which location provides the best reception
and the maximum number of channels. Be sure
to run a new channel scan on your TV in each
position. Refer to the instruction manual that came
with your TV if you are not sure how to do this.
Position or mount the antenna as high as possible
or near a window for best performance.
Connect the antenna to your TV using the
amplifier provided as described in the installation
section. This will enhance reception for most
users. However, depending on your location and
signal environment, the antenna may work best
without the amplifier. If you are having trouble
with reception, you may try removing the amplifier
and connecting the antenna directly to the TV.
Visit www.antennaweb.org or www.dtv.gov and
look for the DTV Reception Maps to determine
the available television stations and location
of the broadcast towers in your area.
26438
Antena amplificada
HD de plegable
Manual del usario
7
Introducción:
El antena amplificada HD de plegable 26438 está
diseñada especialmente para recibir señales
de difusión televisiva terrestre tanto digital
como analógica. El elegante y compacto diseño
quedará bien con cualquier estilo de decoración.
Medidas de seguridad importantes:
•Solo use el adaptador de corriente
homologado por UL provisto.
•Esta antena es solo para uso en interiores.
•No instale esta antena en lugares húmedos
o lugares que puedan tener humedad.
Características:
•VHF/UHF/HDTV
•Impedancia: 75 Ohm
•Low-noise USB-powered amplifier
•Diseño esbelto y moderno
Contenido del paquete:
•Antena digital para interiores
•Adaptador de corriente homologado por UL
•Cable micro USB
•Base para la antena
Antena digital para interiores
Adaptador
de corriente
homologado
por UL
Cable
micro USB
Base para la antena
8
Montaje en la pared
Para obtener la mejor recepción, le conviene
instalar la antena por encima del televisor. Siga las
siguientes instrucciones de montaje de la antena
para instalarla en la pared correctamente.
1. Localice los accesorios de montaje.
2. Busque las herramientas abajo especificadas
a. Algunas de las herramientas que necesitará son
las siguientes:
i. Cinta métrica
ii. Lápiz o lapicero para marcar el lugar en
donde hará los orificios
iii. Broca de 1/8” (3,5 mm) y taladro
iv. Martillo
v. Destornillador Phillips
3. Identifique el lugar en dónde desea instalar la
antena.
4. Use la cinta métrica y un lápiz, marque
dos puntos en la pared a 1.5 pulgadas de
• Accesorios para el
montaje en la pared
•Manual del usuario
•Amplificador en línea de bajo
ruido con alimentación por USB
Accesorios para el
montaje en la pared
Manual del
usuario
Amplificador en
línea de bajo ruido
con alimentación
por USB
9
distancia.
5. Use una broca de 1/8" y cuidadosamente
haga los dos agujeros que marcó en el paso 4.
6. Con el martillo coloque los anclajes para
pared de yeso provistos hasta que queden al
ras de la pared.
7. Use el destornillador Phillips. Atornille los
tornillos provistos hasta que queden a 1/16"
de la pared.
8. Para instalar la antena, alinee las ranuras
en la parte posterior de la antena con los
tornillos.
Asegúrese de que el cable coaxial haya
quedado en la dirección deseada utilizando
el canal de cable en la parte inferior de la
antena.
Instalación:
1. Conecte el cable coaxial de la antena a
la “ANT IN” amplificadora de potencia.
2. Conecte el cable coaxial del
amplificador con la etiqueta “TO TV”
a la parte posterior del televisor.
3. Para televisores equipados con puertos
USB: Conecte el cable USB provisto al
puerto USB del amplificador, luego conecte
el otro extremo al puerto USB del televisor.
Indice
Lingue:
Altri manuali GE Antenna
GE
GE Quadcore HD Manuale utente
GE
GE 29884 Manuale utente
GE
GE Ultra Edge HD Manuale utente
GE
GE 24700-2 Manuale utente
GE
GE 33692-2 Manuale utente
GE
GE 25993 Manuale utente
GE
GE 14846 Manuale utente
GE
GE 33691 ultra-flat digital amplified antenna Manuale utente
GE
GE 43452 Manuale utente
GE
GE 34134 Manuale utente
Manuali Antenna popolari di altre marche
Alfa Network
Alfa Network APA-L01 Manuale utente
Naval
Naval PR-422CA Manuale utente
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuale utente
TERK Technologies
TERK Technologies TV44 Manuale utente
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuale utente
HP
HP J8999A Manuale utente
