GE 3300 Manuale utente
Part Number 80172-01
Rev. N (08/07)
Bently Nevada™ Asset Condition Monitoring
Installation Manual
3300 System Installation
3300 System Installation Manual
ii
Copyright © 1987. Bently Nevada LLC.
All rights reserved.
The information contained in this document is subject to change without notice.
The following are trademarks of General Electric Company in the United States and other
countries:
Bently Nevada Keyphasor, Proximitor
Contact Information
The following ways of contacting Bently Nevada are provided for those times when you
cannot contact your local representative:
Mailing Address 1631 Bently Parkway South
Minden, Nevada USA 89423
USA
Telephone 1.775.782.3611
1.800.227.5514
Fax 1.775.215.2873
Internet www.ge-energy.com/bently
iii
Additional Information
Notice:
This manual does not contain all the information required to operate and maintain
the product. Refer to the following manuals for other required information.
3300 System Overview (Part Number 80171-01)
3300 System Troubleshooting (Part Number 80173-01)
The above two documents and 80172 are available as Part Number 80170-01 or -02.
3300/12 AC Power Supply (Part Number 89602-01)
3300/14 DC Power Supply (Part Number 101256-01)
3300/03 System Monitor (Part Number 89604-01)
3300 Internal Barrier Manual (Part Number 88837-01)
Product Disposal Statement
Customers and third parties, who are not member states of the European Union, who are
in control of the product at the end of its life or at the end of its use, are solely
responsible for the proper disposal of the product. No person, firm, corporation,
association or agency that is in control of product shall dispose of it in a manner that is
in violation of any applicable federal, state, local or international law. Bently Nevada LLC
is not responsible for the disposal of the product at the end of its life or at the end of its
use.
Symbols
Special symbols are used in the manual to illustrate specifics in the step-by-step
processes. For example:
3300 System Installation Manual
iv
Contents
1. RECEIVING INSPECTION............................................................................................................................ 1
2. HANDLING & STORING CONSIDERATIONS........................................................................................ 2
3. RACK ASSEMBLY OPTIONS....................................................................................................................... 3
4. RACK INSTALLATION [PANEL MOUNT]................................................................................................ 4
5. RACK INSTALLATION [19-INCH EIA]..................................................................................................... 5
6. PANEL CUTOUT DIMENSIONS................................................................................................................. 6
7. WEATHERPROOF HOUSING INSTALLATION ..................................................................................... 7
8. POWER SUPPLY INSTALLATION ...........................................................................................................13
9. SYSTEM MONITOR INSTALLATION ......................................................................................................15
10. MONITOR INSTALLATION [TYPICAL]..............................................................................................16
11. POWER INPUT MODULE.....................................................................................................................17
12. SIGNAL INPUT RELAY MODULES ....................................................................................................18
13. ALERT RELAY ACTUATION CIRCUITS .............................................................................................23
14. DANGER RELAY ACTUATION CIRCUITS ........................................................................................26
15. FIELD GROUNDING TECHNIQUE.....................................................................................................28
Section 1 - RECEIVING INSPECTION
1
1. RECEIVING INSPECTION
1. Visually inspect the exterior of rack assembly and components for obvious shipping
damage.
2. Inspect interior of monitors and power supply. Loosen screws to pull each monitor and
power supply out from rack.
DAMAGE CLAIMS
If shipping damage is apparent,
file a claim with the carrier and
submit a copy to Bently Nevada
Corporation.
3300 System Installation Manual
2
2. HANDLING & STORING
CONSIDERATIONS
Handling and storing of printed circuit boards is extremely critical. Circuit boards contain
devices that are susceptible to damage when exposed to electrostatic charges. Damage
caused by obvious mishandling of the board will void the warranty. To avoid damage,
observe the following precautions in the order given.
CAUTION
Machinery protection will be
lost when power is removed
from the instrument.
• Prior to servicing, remove all power to the instrument.
• Do not discharge static electricity onto the circuit board. Avoid tools or procedures that
would subject the circuit board to static damage. Some of the possible causes include
ungrounded soldering irons and nonconductive plastics or similar materials.
• Personnel must be grounded with a suitable grounding strap (such as 3M Velostat No.
2060) prior to handling or performing maintenance on a printed circuit board.
• Transport and store circuit boards in electrically conductive bags or foil.
• Use extra caution during dry weather. Relative humidity less than 30% tends to multiply
the accumulation of static charges on any surface.
Section 3 - RACK ASSEMBLY OPTIONS
3
3. RACK ASSEMBLY OPTIONS
EXTERNAL DIMENSIONS
A B
01,11,21,31 = 4 POSITIONS 11.00 IN. (279.4 mm) 8.00 IN. (203.2 mm)
02,12,22,32 = 6 POSITIONS 15.00 IN. (381.0 mm) 12.00 IN. (304.8 mm)
03,13,23,33 = 8 POSITIONS 19.00 IN. (482.6 mm) 16.00 IN. (406.4 mm)
04,14,24,34 = 10 POSITIONS 23.00 IN. (584.2 mm) 20.00 IN (508.0 mm)
05,15,25,35 = 12 POSITIONS 27.00 IN (685.8 mm) 24.00 IN. (609.0 mm)
06,16,26,36 = 14 POSITIONS 31.00 IN. (787.4 mm) 28.00 IN. (711.2 mm)
07,17,27,37 = 8 POSITIONS 19.00 IN. (482.6 mm) 16.00 IN (406.4 mm)
3300 System Installation Manual
4
4. RACK INSTALLATION [PANEL MOUNT]
1. Slide rack through panel cutout.
Section 5 - RACK INSTALLATION [19-INCH EIA]
5
5. RACK INSTALLATION [19-INCH EIA]
3300 System Installation Manual
6
6. PANEL CUTOUT DIMENSIONS
OPTIONS RACK SIZE A
01,11,21,31 4 POSITIONS 8.56 IN. (217.5 mm)
01.12.22.32 6 POSITIONS 12.57 IN (319.3mm)
03,13,23,33 8 POSITIONS 16.57 IN. (420.8mm)
04,14,24,34 10 POSITIONS 20.58 IN (522.7 mm)
05,15,25,35 12 POSITIONS 24.58 IN (624.3 mm)
06,16,26,36 14 POSITIONS 28.59 IN (726.2 mm)
07,17,27,37 8 POSITIONS SEE SECTION 5
NOTE
The dimensions specified for "A" in the table above refer to the case where a panel is
being cut out for the rack only and not for the weatherproof housing. The panel cutout
dimensions for the weatherproof housing are specified in the "Tabulated Data" table in
section 7 under the "E" column.
Altri manuali per 3300
2
Indice
Altri manuali GE Strumento di misura
GE
GE DigitalFlow GS868 Guida utente
GE
GE Optica Manuale utente
GE
GE 3300 Manuale utente
GE
GE DMS Go Manuale utente
GE
GE Centricity MP3510 Manuale utente
GE
GE CTF878 Guida alla risoluzione dei problemi
GE
GE JXSOUSV1 Manuale utente
GE
GE N60 Manuale utente
GE
GE Kelman MULTITRANS Manuale utente
GE
GE MAC 800 Manuale utente
GE
GE Bently Nevada 3300/16 Manuale utente
GE
GE MAC VU360 Manuale utente
GE
GE PanaFlow HT Manuale utente
GE
GE N60 Manuale utente
GE
GE Hydran M2-X Manuale utente
GE
GE Optica Manuale utente
GE
GE SCOUT100-Ex Manuale utente
GE
GE RSDetection RS-S131-200-ER0000 Manuale utente
GE
GE Druck DPI 705 Manuale utente
GE
GE Paywise Manuale utente
