Geeetech Acrylic I3 Pro Istruzioni operative

Assemble Instruction of GeeetechAcrylic Prusa I3 Pro C

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

Safety Instructions

Building the printer will require a certain amount of physical dexterity, common sense

and a thorough understanding of what you are doing. We have provided this detailed

instruction to help you assemble it easily.

However ultimately we cannot be responsible for your health and safety whilst

building or operating the printer, with that in mind be sure you are confident with

what you are doing prior to commencing with building or buying. Read the entire

manual to enable you to make an informed decision.

Building and operating involves electricity, so all necessary precautions should be

taken and adhered to, the printer runs on 12V supplied by a certified power supply, so

you shouldn’t ever have to get involved with anything over 12V but bear in mind

there can still be high currents involved and even at 12V they shouldn’t be taken

lightly.

High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end

can run about 230°C, the heated bed runs 110°C and the molten plastic extruded will

initially be at around 200°C, so special care and attention should be made when

handling these parts of the printer during operation.

We wouldn’t recommend leaving your printer running unattended, or at least until you

are confident to do so. We cannot be held responsible for any loss, damage, threat,

hurt or other negligent result from either building or using the printer.

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

Preparation

1. Unpack the kit and check if all parts are in the box and check the condition of each

part, there might be some damage during shipping. To help you with this, there is

BOM in the box and each bag was labeled with part number.

2. Contact our customer service immediately by email or through the website if you

find any missing or damaged parts. And on the bottom of the BOM, there is a

signature of reviewer, please take a picture of it and attach the picture in your mail.

3. Read through each chapter of these instructions to gain an over-all idea of what is

involved and how long it might take, before starting on the work described.

4. Before you start, you can put all the part in order to save your time especially those

screws and nuts. Do not mix them up.

5. Ensure you have the necessary skills to carry out the work, or enlist the help of

someone who does.

6. Work on a big firm table or bench in a clean dry well-lit area.

7. This kit contains tiny parts; please keep them away from kids under 3.

8. Ask for help if you run into any problems - our contact details are on the website

and we will always do our best to resolve any problems encountered.

ShenzhenGETECHCO.

LTD

GEEETECH

1Unfold the box and check the package list

Unfold the package and take all the parts out to check the condition of the items.

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

All the acrylic plate has been etched with part ID and the plate is covered with

a sheet of kraft paper, you need to tear them off.

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

Required parts

Tips:

1. Before assembly, you are advised to put all the parts, especially the screws and nuts

in order, which will save you a lot of time looking for the required parts.

2. The part ID is corresponding to the number labeled on the bag of every part. Some

parts may not have label, you can refer to the pictures on the package list.

2 Assemble Y axis

2.1 Assemble the rods of a Y axis

Step1. Assemble the 2 threaded rods.

picPart IDRequired number

NO.52M10 threaded rod

NO.A142Y plate connecting

plate

NO.186M8 spring washer

NO.98M10 washer

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

NO.128M10 nut

Thread the nuts and washers into the two M10 threaded rods separately. The order

should be:

1) Thread the acrylic fender (Y plate connecting plate) in the middle.

2) Thread the M10 washer > M8 spring washer >M10 nut > M10 nut > M10 washer

on the left

3) Thread theM10 washer < M8 spring washer < M10 nut < M10 nut< M8 spring

washer < M10 washer on the right

Step2. Assemble the 2 smooth rods

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

picPart IDRequired numberRequired parts

NO.32M8 smooth rod

NO.394

LM8UU Linear bearings

Slide 2 bearings on each smooth rod. Before you slide the bearings please make sure

they are clean.

1.2. Attach the front and rearAcrylic support plates of the rods.

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

picPart

Required

number

Required

parts

NO. A9,

A 10

2Acrylic

plate( front)

NO. A

11, A 12

2Acrylic

plate( rear)

NO.94M10 washer

NO.124M10 nut

Step1. Slide the rods into the acrylic plate; adjust the length so that the smooth rods fit

snugly between the front and rear piece.

Step2. Screw up the rods and plate with M10 nut and M10 washer.

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

ShenzhenGETECHCO.

LTD

GEEETECH

* Tips: the Y-axis must be a rectangle, that is the rods on both side should be parallel,

so is the front and back plate. Otherwise it will cause obstruction for the belt later.

You can use a Digital Caliper to measure.

2.2 Assemble the Y idler

picPart IDRequired numberRequired parts

NO.382624ZZ Ball bearing

NO.661bearing holder

www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858

Altri manuali per Acrylic I3 Pro

Indice

Altri manuali Geeetech Stampante 3D

Geeetech

Geeetech Aluminum Prusa I3 Manuale utente

Geeetech

Geeetech Rostock 301 Manuale utente

Geeetech

Geeetech Duplicator 5 Manuale utente

Geeetech

Geeetech E180 Manuale utente

Geeetech

Geeetech Rostock mini Manuale

Geeetech

Geeetech A30 Manuale utente

Geeetech

Geeetech A10T Manuale utente

Geeetech

Geeetech Prusa I3 A pro Manuale utente

Geeetech

Geeetech E180 Manuale utente

Geeetech

Geeetech I3 Pro C Manuale utente

Geeetech

Geeetech Acrylic I3 Pro Manuale utente

Geeetech

Geeetech Delta Rostock mini G2 Manuale utente

Geeetech

Geeetech Prusa I3 X Manuale utente

Geeetech

Geeetech Delta Rostock mini G2 pro Manuale di istruzioni

Geeetech

Geeetech Acrylic I3 Pro Manuale utente

Geeetech

Geeetech Rostock 301 Manuale utente

Geeetech

Geeetech Prusa I3 A pro Manuale utente

Geeetech

Geeetech Duplicator 5 Manuale utente

Geeetech

Geeetech Acrylic I3 Pro Istruzioni operative

Geeetech

Geeetech PrusaI3 X Manuale utente

Geeetech

Geeetech Prusa I3 X Manuale di istruzioni

Geeetech

Geeetech acrylic Prusa I3 Istruzioni operative

Geeetech

Geeetech acrylic Prusa I3 Manuale utente

Geeetech

Geeetech Aluminum Prusa I3 Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente