Geeetech Prusa I3 X Manuale utente
User Manual for Geeetech I3 X
Safety Instructions
Building the printer will require a certain amount of physical dexterity, common sense and a
thorough understanding of what you are doing. We have provided this detailed instruction to help
you assemble it easily.
However ultimately we cannot be responsible for your health and safety whilst building or
operating the printer, with that in mind be sure you are confident with what you are doing prior to
commencing with building or buying. Read the entire manual to enable you to make an informed
decision.
Building and operating involves electricity, so all necessary precautions should be taken and
adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn’t ever have
to get involved with anything over 12V but bear in mind there can still be high currents involved
and even at 12V they shouldn’t be taken lightly.
High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end can run about
230°C, the heated bed runs 110°C and the molten plastic extruded will initially be at around 200°C,
so special care and attention should be made when handling these parts of the printer during
operation.
We wouldn’t recommend leaving your printer running unattended, or at least until you are confident
to do so. We cannot be held responsible for any loss, damage, threat, hurt or other negligent result
from either building or using the printer.
Check the power input
This step is very important. If you didn’t choose the wright power input, the power supply unit will be burned out.
Check the power input of the power supply unit. You can choose either 110V or 220V according to the Power
regulation in your country.
Tear off the yellow sticky note to check it. You can use a hard stick to reach into the power box and switch it.
www.geeetech.com
ShenZhen GETECH CO.,LTD
1
1 Software Resources
1.1 Repetier-Host
We use the latest Repetier host 1.6.0 as the printer control software, here is the link for download:
http://www.geeetech.com/wiki/index.php/Repetier-Host#Download
After downloading and installation, it can be used.
1.2 Driver
Connect the printer to computer with USB cable, the motherboard driver installer will automatically
appear. If not, you can download FT232RQ here, which is the driver of GT2560:
http://www.geeetech.com/wiki/index.php/Prusa_I3_X#Install_the_drivers
www.geeetech.com
ShenZhen GETECH CO.,LTD
2
Download and install, you can find the corresponding serial port in the Windows "Device
Manager":
1.3 Arduino IDE
In the process of using the printer you may need to re-upload the firmware, and the software you
need to use is Arduino.
About how to upload firmware, please refer to FAQ.
2 Connect the Printer
After the above software is installed, we can connect the printer to the computer. Plug the USB into
the computer, open Repetier host, click the icon in the top right corner, and the dialog
www.geeetech.com
ShenZhen GETECH CO.,LTD
3
box of printer settings will appear.
www.geeetech.com
ShenZhen GETECH CO.,LTD
4
Select corresponding COM port of the printer and baud rate as 250,000 in the drop-down menu.
Click Apply after the setting. Shown as below.
www.geeetech.com
ShenZhen GETECH CO.,LTD
5
After setting, click the button in the top left corner of Home Page. When the button turns
green and changes into , the printer connection is successful.
www.geeetech.com
ShenZhen GETECH CO.,LTD
6
3 Printer Setting
3.1 Printer Speed
Set the running speed of printer as 1000 in the printer settings in order to avoid collision because of
high speed during the test. After follow-up tests are completed it can be changed back to the original
value. (Recommend speed of Z-axis should not be too high, 1000 is OK)
Travel feed rate: 1000mm/min
Z-Axis feed rate: 1000mm/min
3.2 Number of Extruder and Nozzle Diameter
The number of extruder is set as 1. The diameter of print head is set according to the actual
www.geeetech.com
ShenZhen GETECH CO.,LTD
7
size, here is 0.4mm.
3.3 Printer Shape
Here the printer shape of I3X is Classic Printer;
For home position, choose Min;
Altri manuali per Prusa I3 X
3
Indice
Altri manuali Geeetech Stampante 3D
Geeetech
Geeetech Prusa I3 A pro Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Istruzioni operative
Geeetech
Geeetech A10M Manuale utente
Geeetech
Geeetech Delta Rostock mini G2 pro Manuale di istruzioni
Geeetech
Geeetech Prusa I3 X Manuale di istruzioni
Geeetech
Geeetech Prusa I3 M201 Manuale di istruzioni
Geeetech
Geeetech A30T Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Istruzioni operative
Geeetech
Geeetech Duplicator 5 Manuale utente
Geeetech
Geeetech A10 Manuale utente
Geeetech
Geeetech Aluminum Prusa I3 Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Istruzioni operative
Geeetech
Geeetech Delta Rostock mini G2 Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Istruzioni operative
Geeetech
Geeetech Rostock 301 Manuale utente
Geeetech
Geeetech A10M Manuale utente
Geeetech
Geeetech Prusa I3 M201 Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Manuale utente
Geeetech
Geeetech A10 Manuale utente
Geeetech
Geeetech acrylic Prusa I3 Manuale utente
