Geeetech Acrylic Prusa I3 Manuale utente

Table of Content

Identify the Printed Parts---------------------------------------------------------------- 3

Build the chassis

Assemble the port and starboard sides of the chassis------------------- 4

Assemble the Y idler--------------------------------------------------------------5

Assemble the front and back of the chassis-------------------------------- 6

The finished chassis---------------------------------------------------------------7

Attach the Y Plate--------------------------------------------------------------------------9

Build the X-Z axes--------------------------------------------------------------------------11

Build the X-Z plate-------------------------------------------------------------------------16

Attach the heatbed------------------------------------------------------------------------19

Assemble the extruder--------------------------------------------------------------------21

Attach the end stoppers-------------------------------------------------------------------24

Identify the Printed Parts

ID Number

Part Name

Number of

Parts

Chassis corners

Y motor mount

Y idler

Y belt holder assembly

Z left bottom

Z right bottom

X motor mount

X idler

X carriage

Z right top

Z left top

End stopper mount

Wade’s extruder body

Wade’s extruder idler

Wade’s extruder small gear

Wade’s extruder big gear

Hotend mounting plate

Build the chassis

1. Assemble the port and starboard sides of the chassis

Required parts

Number

printed chassis corners (no. 1)

380mm M8 threaded rod

350mm 8mm precision rod

fender washer

LM8UU bearing

m8 nut

M8 washer

1. Hold the printed chassis corners with the semi-circular opening facing upward and inward

2. Put 2 LM8UU bearings on one 350mm precision rod on the port side, and 1 LM8UU on the

starboard side.

3. Slide the precision rods into the semi-circular slots of the printed chassis corners. This step

might require some force. Make sure the precision rods are meeting the ends of the slot. An

optional step is to apply zip ties through the holes on the plastic corners to hold down the

precision rods.

4. Slide the 380mm threaded rods through the chassis corners right beneath the precision rods.

Put m8 nuts, m8 washer, and m8 fender washers on the threaded rods in the following

order:

m8 nut –m8 washer –chassis corner –m8 washer –m8 nut –m8 nut –m8 fender

washer –m8 fender washer –m8 nut –m8 nut- m8 washer –chassis corner –m8

washer –m8 nut (see pictures below for a visual illustration)

5. Tighten the nuts

Note: the top assembly is on the port side, and the bottom assembly goes to the starboard side.

2. Assemble the Y idler

Required parts

Number

623ZZ bearing

Printed Y idler (ID no. 3)

M3-25 screw

M3 nut

1. Put the M3-25 screw thru the printed Y idler piece, with two 623ZZ bearings in between. Lock

the other end of a M3 nut.

3. Assemble the front and back of the chassis

Required parts

Number

205mm M8 threaded rod

310mm M8 threaded rod

Printed Y motor mount (no. 2)

Assembled Y idler

M8 nut

M8 washer

M8 fender washer

Note: the easier way to put on these nuts and washers is to put one the inside ones first, then

sandwich the rod between two chassis corners, and then put on the outside nuts and washers.

1. Put m8 nuts, washers, and assembled Y idler on a 205mm m8 threaded rod. Slide this rod thru

the top holes of the front chassis corners. The order is: nut –washer –chassis corner –washer

–nut –nut –washer –assembled Y idler –washer –nut –nut –washer - chassis corner –

washer –nut. Do not tighten yet.

2. Repeat the previous step without the Y idler, and fix the rod on the bottom holes of the chassis

corner. The order is: nut –washer –chassis corner –washer –nut –nut –washer –chassis

corner –washer –nut. Do not tighten yet.

Pictures for step 1 and 2

3. nut –washer –chassis corner –washer –nut –nut –washer –Y motor mount –washer –nut –

nut –washer –chassis corner –washer –nut. Do not tighten yet.

4Align the rods and tighten all nuts so the chassis will not fall apart. You might need to adjust

the chassis later when mounting the Y plate.

5 Put the 310mm and 205mm rods through the printed Y motor mount, with orientation

shown in the picture above. The 310mm should be going through the top holes in the

chassis corners. The order of washers and nuts on the 310mm rod is: nut –fender washer –

fender washer –nut –nut –washer –chassis corner –washer –nut –nut –washer –Y

motor mount –washer –nut –nut –washer –chassis corner –washer –nut –nut –fender

washer –fender washer –nut. The order of nuts and washers on the 205mm

Pictures for step 3 and 4

4. Finished Chassis

Congratulations, now you have the chassis made. It should look like what’s in the picture below.

Attach the Y Plate

Required parts

Number

Acrylic bed

M3-16 screw

M3 nut

Y belt holder assembly 1 (no.4)

Y belt holder assembly 2(no. 5)

M3-10 screw

Zip ties

GT-2 timing belt

~70cm

Nema-17 motor

GT-2 20 teeth pulley

1. Insert four M3 nuts into the hexagonal slots in the Y belt holder assembly 1.

2. Loosely attach the two rectangular pieces to the main piece using four m3-16 screws. Make

sure the flat surface is facing outward.

3. Attach the acrylic Y bed to the chassis using 3 zip ties. Make sure the bed slide freely on the

chassis. Also attach a Nema 17 motor to the Y motor holder using two M3-10 screws, and

attach a GT2 20 teeth pulley on the motor’s shaft.

4. Attach the Y belt assembly to the acrylic bed using two m3-16 screws and two m3 nuts. Take

70cm of GT2 timing belt and insert one end into the Y belt holder. Tighten the two m3-16

screws to hold down the belt.

5. Wrap the GT2 timing belt around the Y motor’s aluminum pulley, and around the 623zz

bearings. Insert the other end of the GT2 timing belt into the Y belt holder and tighten the

m3-16 screws. The belt should be tight with tension. As the bed moves on the chassis, there

should be no skipping.

Altri manuali per acrylic Prusa I3

Indice

Altri manuali Geeetech Stampante 3D

Geeetech

Geeetech I3 Pro C Manuale utente

Geeetech

Geeetech Prusa I3 X Manuale di istruzioni

Geeetech

Geeetech A30T Manuale utente

Geeetech

Geeetech Acrylic I3 Pro Istruzioni operative

Geeetech

Geeetech Mizar S Manuale utente

Geeetech

Geeetech A30 Manuale utente

Geeetech

Geeetech Prusa I3 X Manuale utente

Geeetech

Geeetech PrusaI3 X Manuale utente

Geeetech

Geeetech Acrylic I3 Pro Manuale utente

Geeetech

Geeetech A10M Manuale utente

Geeetech

Geeetech Acrylic I3 Pro Istruzioni operative

Geeetech

Geeetech Prusa M201 Manuale dell'operatore

Geeetech

Geeetech acrylic Prusa I3 Manuale utente

Geeetech

Geeetech Rostock mini Manuale

Geeetech

Geeetech A10M Manuale utente

Geeetech

Geeetech acrylic Prusa I3 Istruzioni operative

Geeetech

Geeetech Acrylic I3 Pro Istruzioni operative

Geeetech

Geeetech Delta Rostock mini G2S Pro Manuale utente

Geeetech

Geeetech A20T Manuale utente

Geeetech

Geeetech Acrylic I3 Pro Manuale utente

Geeetech

Geeetech Rostock 301 Manuale utente

Geeetech

Geeetech E180 Manuale utente

Geeetech

Geeetech Rostock 301 Manuale utente

Geeetech

Geeetech Delta Rostock mini G2 Manuale dell'operatore

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente