Geeetech acrylic Prusa I3 Istruzioni operative
Assemble Manual of GeeetechAcrylic Prusa I3 (8mm)
ShenzhenGETECHCO.
,
LTD
GEEETECH
Warning:
1. This kit contains tiny parts; please keep them away from kids under 3.
2. Building and operating 3D printer involves electricity, so all necessary precautions
should be taken and adhered to.
3. Building a 3d printer requires a certain amount of handling ability and some
common sense and working principle of 3D printer.
However, do not worry; with this build instruction in hand, you can finish the
assembly easily.
1Unfold and check the package
Unfold the package and take all the parts out to check the condition of the items. As
you can see, all the parts are packed very carefully.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
zAll the acrylic plate has been etched with part ID.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
Tips:
1. Before assembly, you are advised to put all the parts, especially the screws and nuts
in order, which will save you a lot of time looking for the required parts.
2. The part ID is corresponding to the number labeled on the bag of every part.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
2 Assemble Y axis (the bottom part of the chassis)
2.1 Assemble the rods of a Y axis
Step1. Assemble the 2 threaded rods.
Part IDRequired numberRequired parts
NO.52M10 threaded rod
NO.A 142Acrylic Fender
NO.186M8 spring washer
NO.98M10 washer
NO.128M10 nut
Thread the nuts and washers into the two M10 threaded rods separately. The order
should be:
M10 washer > M8 spring washer >M10 screw > M10 screw > M10 washer > acrylic
fender > M10 washer > M8 spring washer > M10 screw > M10 screw > M8 spring
washer > M10 washer
ShenzhenGETECHCO.
,
LTD
GEEETECH
Step2. Assemble the 2 smooth rods
Part IDRequired numberRequired parts
NO.32M8 smooth rod
NO.394LM8UU Linear bearings
Slide 2 bearings on each smooth rod. Before you slide the bearings please make sure
they are clean.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
1.2. Attach the front and rear Acrylic support plates of the rods.
Part IDRequired numberRequired parts
NO. A9, A 102Acrylic plate( front)
NO. A 11, A 122Acrylic plate( back)
NO.94M10 washer
NO.124M10 nut
Slide the rods into the acrylic plate, Adjust the length so that the smooth rods fit
snugly between the front and back piece.
Each corner gets a washer and a nut. Adjust the inner and outer nuts so that the end of
the rod is flush with the outside M10 nut.
Do the same on all four corners.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
* Tips: the Y-axis must be a rectangle, that is the rods on both side should be parallel,
so is the front and back plate. Otherwise it will cause obstruction for the belt later.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
2.2 Assemble the Y idler
Part IDRequired numberRequired parts
NO.382624ZZ Ball bearing
NO.661Y belt holder
NO.271M3 x 20 screw
NO.151M3 wing nut
NO.351M4 x25 screw
NO.141M4 lock nut
Step1. Thread the M3 x 20 screw through the Y idler piece.
Put the M4 x25 screw through the holes with the 624ZZ bearings in between. Lock
the other end with a M3 nut.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
Step2. Mount the assembled idler onto the front support plates. And screw it with a
wing nut.
*Please leave enough room for the belt between the ball bearing and the screw.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
Altri manuali per acrylic Prusa I3
4
Indice
Altri manuali Geeetech Stampante 3D
Geeetech
Geeetech prusaI3 pro C Manuale utente
Geeetech
Geeetech A10T Manuale utente
Geeetech
Geeetech A30 Manuale utente
Geeetech
Geeetech Prusa I3 A pro Manuale utente
Geeetech
Geeetech acrylic Prusa I3 Istruzioni operative
Geeetech
Geeetech I3 Pro C Manuale utente
Geeetech
Geeetech A30T Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Manuale utente
Geeetech
Geeetech acrylic Prusa I3 Manuale utente
Geeetech
Geeetech Aluminum Prusa I3 Manuale utente
Geeetech
Geeetech Aluminum Prusa I3 Manuale utente
Geeetech
Geeetech A10M Manuale utente
Geeetech
Geeetech acrylic Prusa I3 Manuale utente
Geeetech
Geeetech Acrylic I3 Pro Istruzioni operative
Geeetech
Geeetech Prusa I3 A pro Manuale utente
Geeetech
Geeetech Mizar S Manuale utente
Geeetech
Geeetech Rostock 301 Manuale utente
Geeetech
Geeetech Prusa I3 X Manuale di istruzioni
Geeetech
Geeetech A30 Manuale utente
