Giada MI-D525 Manuale utente
www.giadatech.com User’s Manual
MI-D525
All right reserved
Version 001
Motherboard
21
Gratitude ……………………………………………………………………………
I. About the product ………………………………………………………………
1. Picture of the motherboard ………………………………………………
2. Features ……………………………………………………………………
2.1 Processor ………………………………………………………………
2.2 Memory …………………………………………………………………
2.3 BIOS ……………………………………………………………………
2.4 Interfaces of peripherals ………………………………………………
2.5 Power management……………………………………………………
II. Hardware installation……………………………………………………………
1. Layout of motherboard ……………………………………………………
2. Installing memory …………………………………………………………
3. Motherboard jumper setting ………………………………………………
3.1 SATA1/SATA2 (Serial ATA flat-cable sockets) ………………………
3.2 CPU_FAN1 (CPU FAN socket) ………………………………………
3.3 CLR_CMOS(CMOS pin) ………………………………………………
3.4 F_USB1/ F_USB2 (frond-end USB pin) ……………………………
3.5 F_ AUDIO(Pins for front-end audio adapter) ………………………
3.6 ATX 12V (12V Power receptacle) ……………………………………
3.7 F_ PANEL (Front-end control panel) …………………………………
4. Rear panel interface ………………………………………………………
Contents
III. BIOS setting ……………………………………………………………………
1. Main menu …………………………………………………………………
2. Main (standard CMOS setup) ……………………………………………
3. Advanced (Advanced BIOS setup) ………………………………………
4. Boot Configuration …………………………………………………………
5. Security Setup ………………………………………………………………
6. Exit ……………………………………………………………………………
IV. Software installation ……………………………………………………………
1. Install driver for motherboard ……………………………………………
1.1 Install driver for chipset ………………………………………………
1.2 Install sound card driver ………………………………………………
1.3 Install driver for on-board LAN chip …………………………………
1.4 Install driver for graphic card …………………………………………
2. HD_AUDIO and sound card setup ………………………………………
3
4
5
5
5
5
5
6
7
8
8
9
9
10
10
11
12
13
15
4
5
16
18
19
20
20
22
24
25
25
27
28
29
30
30
www.giadatech.com
4
3
Gratitude I. About the product
1. Picture of the motherboard
Thank you for choosing Giada motherboard.
Giada MI-D525 is based on Dual-core Intel® Atom™ processor D525
It supports DDR3 800 Dual-channel memory, on-board HD-AUDIO sound card.
Support USB2.0.
Any question about the product, please send e-mail to our support center.
Headquarter:
USA office: [email protected]
www.giadatech.com
NOTE: This is Giada real product photo show for your reference only, Product
appearance depends on goods.
6
5
2.1 Processor
· On-board Dual-core Intel® Atom™ processor D525
· On-board Intel® GMA3150.
2.2 Memory
·
·
2.3 BIOS
·
·
·
·
2.4 Interfaces for peripherals
·
·
·
·
·
·
·
·
·
2.5 Power management
·
·
2. Features
;
Supports 240-Pin DDR3 800MHz memory * 1;
2GB at maximum.
Supports PNP, APM and ATAPI;
Supports ACPI and DMI;
Automatic detection and supporting hard disk whose LBA mode is over 160G;
End-users can easily upgrade the motherboard with BIOS.
One PS/2 keyboard connector;
One PS/2 mouse connector;
Two RJ45 network interface (PCIe Gigabit Ethernet);
Supports two SATA Ⅱhard-disk interfaces;
Six high-speed transmission ports (max. 480Mb/s) which support USB2.0
and are compatible with USB1.1;
On-board HD-AUDIO audio adapter;
Interfaces on panels can be compatible with HDD LED, Speaker, etc;
One CMOS contact pin;
One system FAN socket.
Support APM and ACPI;
Compatible with energy star “Green PC”.
II. Hardware installation
www.giadatech.com
Warning
·
·
·
·
·
The motherboard consists of a great number of ICs and other components.
These ICs might be damaged by the static charge. Therefore, the user must
make the following preparations before installation:
Turn off the power of the computer. It is preferable the power cord be unplugged.
Take care not to contact the metal wires and theirs joints on the motherboard
when handling it.
It is preferable that the operator wear the anti-static wrist strap when handling
the IC components.
Before the ICs are installed, the components of the motherboard should be
placed on the anti-static mat or bag.
When you remove the plug on the ATX power supply of the motherboard,
make sure the switch of the power supply is in OFF state.
Installing the motherboard onto the computer case:
For most of the computer cases, the multiple fixing holes left on their bottoms
can be used for securing the motherboard and preventing short circuit. During
your operation, take care not to allow the screws to contact any circuit or part on
PCB. When circuits on the surface of the motherboard get close to the fixing
holes, you can use the plastic sheet to separate the screws from the board
surface so as to avoid damage or failure of the motherboard.
8
7
1. Layout of motherboard 2. Installing memory
Please install the memory in accordance with the following procedures:
· Align the golden finger of the memory to the groove of the interface slot and
pay attention the concave hole of golden finger should be aligned to the
convex point of the slot.
· Finally, insert the memory into the interface slot gently. If no error occurs at
the moment, insert the card forward in the slot till the white buckle is
automatically engaged in the concave hole at the two sides of the memory.
Note
In order to avoid damages to the motherboard or the components, the user must
make sure the power supply to the computer is turned off before the memory or
other component is installed or removed. As the groove is set at the golden finger
of the DDR DIMM, the memory can only be inserted into the slot with one direction.
During installation, the user only needs to align the golden finger and the dual-
channel groove of the interface slot and insert it gently. To avoid damage, never
apply excessive force in that process.
3. Motherboard jumper setting
Note:The user should notice that all sockets are marked with PIN1. The mark “#”
indicates the ex-factory default values.
www.giadatech.com
123456
7
8
9
10
11
12 13
14
15
16
1. PS/2 port
2. COM+LPT port
3. VGA port
4. RJ45+2* USB port
5. RJ45+2* USB port
6. JACK AUDIO port
7. Front audio
8. PCI Slot
9. USB Header
10. SATA Ⅱ port
11. Mini PCI-E
12. ATX 12V Power(20-pin)
13. DDR3 SO-DIMM Slot
14. CPU
15. NM10
16. COM Header
10
9
3.1. SATA1/SATA2 (Serial ATA flat-cable sockets)
Serial ATA sockets can reach a transmission speed of 300MB/s, and you can
connect your Serial ATA device to this socket.
3.2. CPU_FAN1 (CPU FAN socket)
This receptacle can be used for connecting CPU/system fan. Its pins are
defined below. The user shall make sure the fan is conforming
PIN Definition
1
2
3
GND
12V
SIGNAL
123
PIN Definition
1-2#
2-3
Normal
CLR_CMOS
www.giadatech.com
1 2 3
3.3.CLR_CMOS(CMOS pin).
The correct time, system hardware and other information are saved in the
CMOS memory of the motherboard. The interruption the computer's power
won't cause the loss of this information, for the CMOS is powered by the
battery on the motherboard. The port is defined as follows:
3.4. F_USB1/ F_USB2 (frond-end USB pin)
In case the USB ports on the rear panel of the machine case are not enough,
the user can use the two sets of extension USB pins provided by this
motherboard. These ports support USB 2.0 devices. The definitions of the
ports are described below:
1
2
10
9
71
PIN Definition
1
2
3
4
5
6
7
GND
TXP
TXN
GND
RXN
RXP
GND
12
11
PIN PIN
Definition Definition
1
3
5
7
9
2
4
6
8
10
5V
USB D0-
USB D0+
GND
NULL
5V
USB D1-
USB D1+
GND
NULL
3.6. ATX 12V (12V Power receptacle)
These audio adapter ports allow you to connect to the wire harness of the
audio adapter. After connection, you can easily control the audio
output/microphone through the front panel of the host (Note: Don't connect
the wire to Pin 4).
The definitions of the ports are described below:
Definition
GND
5V
-
NULL
-
PIN
2
4
6
8
10
Definition
MIC
MIC-BIAS
OUT-R
GND
OUT-L
PIN
1
3
5
7
9
210
19
www.giadatech.com
3.5. F_ AUDIO(Pins for front-end audio adapter)
These audio adapter ports allow you to connect to the wire harness of the
audio adapter. After connection, you can easily control the audio output/
microphone through the front panel of the host (Note: Don't connect the wire
to Pin 4).
The definitions of the ports are described below:
14
13
3.7. F_ PANEL (Front-end control panel)
This socket is used to connect the flat cables on the front-end panel.
Definition
PLED+
PW_LED+
PWRBTN
GND
PLED-
PIN
2
4
6
8
10
Definition
HDLED+
HDLED-
RST
RST+
RST+
PIN
1
3
5
7
9
www.giadatech.com
Definition
3.3V
-12V
GND
PS-ON
GND
GND
GND
-5V
5V
5V
PIN
11
12
13
14
15
16
17
18
19
20
Definition
3.3V
3.3V
GND
5V
GND
5V
GND
PG
5VSB
12V
PIN
1
2
3
4
5
6
7
8
9
10
2
1
4
3
6
5
8
7
10
9
16
15
4. Rear panel interface
1. PS/2.
2. COM+LPT port
3. VGA port
4. RJ45+2* USB port
5. RJ45+2* USB port
6. JACK AUDIO port
Note
The descriptions relating to BIOS in this Manual can only be used for reference
as the BIOS version of the motherboard is upgraded continuously. Giada provides
no guarantee that the contents in this Manual be consistent with the information
you acquire.
BIOS is a basic I/O control program saved in the Flash Memory. Bridging the
motherboard and the operating system, BIOS is used for managing the setup of
the related parameters between them. When the computer is activated, the
system is first controlled by the BIOS program. First, a self-detection called POST
is performed to check all hard devices and confirm the parameters of the
synchronous hardware. Once all detections are completed, BIOS will hand over
the controlling to the operating system (OS). As BIOS serves as the only channel
that connects the hardware and software, whether your computer can run stably
and work in optimized state will hinge on how to properly set the parameters in
BIOS. Therefore, the correct setup of BIOS plays a key role in stably running the
system and optimizing its performance.
The CMOS Setup will save the set parameters in the built-in CMOS SRAM on the
motherboard. When the power is shut off, the lithium battery on the motherboard
will provide continuously power for CMOS SRAM. The BIOS setup program will
allow you to configure the following items:
1.HD drive, floppy drive and peripheral devices;
2.Video display type and display items;
3.Password protection;
4.Power management characteristics.
A.A.State of BIOS Setup
When the computer is started up, BIOS will run the self-detection (Post) program.
This program includes series of diagnosis fixed in BIOS. When this program is
executed, the following information will appear if any error is found:
Press F1 to Run Setup
Press F2 to Load default values and continue
12 3 46
III. BIOS Setting
5
www.giadatech.com
18
17
Key
↑ (Up key)
↓ (Down key)
← (Left key)
→ (Right key)
ESC
Page Up
Page Down
F1
F7
F8
F9
F10
Function
Move to the previous item
Move to the next item
Move to the left item
Move to the right item
Exit the current interface
Change the setup state, or add the values
Change the setup state, or deduct the values
Display the information of the current setup
Load the set values of previous time
Load the safest values
Load the optimized values
Save the settings and exit the CMOS SETUP
C.Auxiliary information
Main interface
When the system enters the main interface of Setup, the major selected contents
will be displayed at the lower part of the interface with the change of the options.
Set interface
When you set the value for each column, you can view the preset value of the
column and the values that can be set if you press F1, for example, the BIOS
default values or CMOS Setup values. To exit the interface for auxiliary information,
press [ESC].
To enter BIOS, you can press F1; to load the default values and enter the system,
you can press F2. After the self-detection process is completed, you can press
DEL to enter the BIOS interface if no error is found. If the indicative information
disappears before you can act, you can shut off the computer and turn on it
again, or you can press the key RESET on the machine case. To restart your
computer, you can also simultaneously press <Ctrl>+<Alt>+<Delete>.
B. Function Keys definitions
1. Main menu
When the system enters the CMOS Setup menu, you can see the main menu on
the upper part of the screen, as shown in Figure 3.1. In this main menu, you can
use the left and right direction keys to select the setup items. Once the item is
selected, the lower part of the computer screen will show the details of setting.
(The options above and their contents may be different from your actual options,
so they are used for reference only).
· Main (standard CMOS setup)
This item is used for setting the date, time, specifications of hard disk and floppy
disk and type of monitor.
· Advanced (advanced BIOS setup)
This item is used for setting the advanced functions provided by BIOS, such as
the virus alarm and priority order of disks for startup process.
Fig 3.1
www.giadatech.com
Indice
Altri manuali Giada Scheda madre
Giada
Giada N70E-DR ITX NAS Manuale utente
Giada
Giada MI-A75 Manuale utente
Giada
Giada MI-E350 Manuale utente
Giada
Giada MI-E350T Manuale utente
Giada
Giada ION2 Manuale utente
Giada
Giada NI-R3188 Manuale utente
Giada
Giada MI-ION2 Manuale utente
Giada
Giada N30M-VA Manuale utente
Giada
Giada MI-H67 Manuale utente
Giada
Giada N70E-DR ITX NAS Manuale utente
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
