Greyline Instruments DFM 5.0 Manuale utente
USER'S GUIDE
Installation & Operation
Instructions
Doppler Flow Meter
Model DFM 5.0
Manual Series A.8.1
Note: This page has been left blank intentionally.
IMPORTANT NOTE: This instrument is manufactured and calibrated to meet product specifications.
Please read this manual carefully before installation and operation. Any unauthorized repairs or
modifications may result in a suspension of the warranty.
If this product is not used as specified by the manufacturer, protection may be impaired.
Available in Adobe Acrobat pdf format
Page 3
DFM 5.0 Doppler Flow Meter
INDEX
Connections ......................................................4
Keypad System ....................................................6
Calibration Menu ..................................................7
Message .........................................................8
Status............................................................8
Password .........................................................9
Units/Mode ......................................................10
Calibration ......................................................11
Relay Parameters .................................................12
Special Functions .................................................13
Sensor Mounting..................................................15
Enclosure Installation ..............................................19
Synchronization ..................................................20
Troubleshooting ..................................................21
Common Questions And Answers ....................................24
Applications Hotline ...............................................26
Product Return Procedure ...........................................27
Warranty ........................................................29
Flow Meter Data Sheet .............................................28
Warranty ........................................................29
Appendix A – Options .............................................30
Data Logger .....................................................36
Specifications ....................................................38
Appendix B - Conversion Table ......................................39
Pipe Charts ......................................................40
CONNECTIONS:
POWER INPUT: The standard model requires AC power input between 100 to 240 VAC 50/60Hz . No
adjustments are necessary for voltages within this range.
Optional DC input model requires 9-32 VDC/7 Watts. Connect to + and −terminals. Connect L (Live)
N (Neutral) and AC Ground.
Optional Thermostat and Heater modules are available rated for 115 VAC or 230 VAC.
IMPORTANT NOTE: To comply with CSA/UL electrical safety standards, AC power input and relay
connection wires must have conduit entry to the instrument enclosure. Installation requires a switch,
overcurrent fuse or circuit breaker in the building (in close proximity to the equipment) that is marked
as the disconnect switch.
Risk of electric shock. Loosen cover screw to access connections. Only qualified personnel
should access connections.
Note: Use of instrumentation over 40°C ambient requires special field wiring.
Note: User replaceable fuse is 2 Amp 250V (T2AL250V).
Page 4
DFM 5.0 Doppler Flow Meter
!
CONNECTIONS
Page 5
DFM 5.0 Doppler Flow Meter
L
NHEATER OPTION
AC
LN
RCVR
GND
TMTR
GND
–+
SYNC
NO
C
NC
NO
C
NC
–
+
4-20mA (1)
RLY2
RLY1
AC
GROUND
TRANSDUCER
GND
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
RLY3 RLY4 RLY5 RLY6
EXTRA RELAYS OPTION
POWER
INPUT
KEYPAD SYSTEM
The following diagram shows the DFM 5.0 menu system. Arrows show the four directions to leave a
menu box. Pressing a corresponding keypad arrow will move to the next item in the direction shown.
Move the cursor (underline) under numerals and increase or decrease numerals with the Çand Èkeys.
To store calibration values permanently (even through power interruptions), press the ü.
DFM 5.0 Doppler Flow Meter
Page 6
CALIBRATION MENU
Page 7
DFM 5.0 Doppler Flow Meter
--Password----------
Password 0000
--Data Logging-------
>Log Site ID 0
Mode Flow
Set Date Feb 18/2007
Set Time 11:27:40
Interval 10sec
Reset Log NO
--Units/Mode--------
>Mode Flow
Linear in
Volume USG
Time min
--Calibration-------
>20mA at 2500.0 USG/m
4mA at 0.000 USG/m
Pipe ID 12.00in
Damping 20%
--Relay Parameters--
>Relay 1
Function Flow
Mode Pump
On 1000 USG
Off 0.000 USG
USG/min
Tot 20130.8 USG
Relays 123456
0.000
--Message-----------
Data log Logging
Log Use 0%
Sensor Good
--24 hr log----------
>Date Feb. 12/2008
Total 0.000ft/s
Average 0.000ft/s
Maximum 0.000ft/s
Max Time 01:57:00
Minimum -1.046ft/s
Min Time 02:35:00
--Status------------
>Velocity 0.00ft/s
Tot 0.000USG
Signal Cutoff 5%
Signal Strength 0%
Sig Confidence 0
Relays123456
20mA at
--Special Functions-
>Language English
Backlight On High
Reset Totalizer NO
Negative Totals NO
Reverse Flow NO
Cal Constant 1.000
Restore Defaults NO
New Password 0000
--Simulation--------
>Output 250USG
4-20mA 5.60mA
Relays 1 23456
--Configuration-----
>Utility Board 1.01
Doppler 1.02
Logger 1.03T
Relays 2
4-20 Outputs 1
--Menu Selections----
>Units / Mode
Calibration
Relay Parameters
Data Logging
Special Functions
Simulation
Configuration
OPTIONAL FEATURES
RUN
The main display shows the units selected from the Units/Mode menu,
Flow or Velocity rate being measured, TOTALIZER and RELAY states.
The DFM 5.0 will start-up with this display and will return to this screen
after a timeout if keys are not pressed in other menus.
MESSAGE
Press Çfrom the RUN display to view status of the data logger and
error/warning messages provided by the instrument. The word Message
will appear on the RUN display if error messages are being generated by
the instrument. Refer to the manual section Error/Warning Messages for a
description. Press üto return to the main display.
STATUS
Press Èfrom the RUN display to view instrument status. Velocity will be
displayed in ft/sec or m/sec.
Tot Displays the current totalizer reading.
Signal Cutoff Adjust the setting in percent to suppress flow readings
at zero flow when fluid swirling or pipe vibration may cause the
instrument to continue reading. Example: Signal Cutoff at 5% will force
the display and outputs to zero when signal strength drops below 5%.
Signal Strength Displays percentage of signal being received by the
ultrasonic sensor.
Sig Confidence This indicates consistent or widely varying flow rates
and helps gauge the quality of the velocity signal in the application.
Relays Energized relays will display as a white character on a black
background.
20mA at Displays the flow rate set as 20mA in the Calibration menu.
Press üto return to the main display.
Page 8
DFM 5.0 Doppler Flow Meter
--Message-----------
Data log Logging
Log Use 0%
Sensor Good
--Status------------
>Velocity 0.00ft/s
Tot 0.000USG
Signal Cutoff 5%
Signal Strength 0%
Sig Confidence 0
Relays123456
20mA at
USG/min
Tot 20130.8 USG
Relays 123456
0.000
24 HR LOG (Data Logging option only)
Press Åfrom the RUN display to view a formatted flow report from
instruments with a built-in data logger. Press Èto scroll down one day or
repeatedly to scroll to a specific date. Up to 365 days can be stored.
Newest date will overwrite the oldest. Press üto return to the main
display.
PASSWORD
The password (a number from 0000 to 9999) prevents unauthorized access
to the Calibration menu.
From the Run display press the Ækey to get to Password. Factory
default password is 0000 and if it has not been changed press the üto
proceed to the Menu Selections screen.
If a password is required, press Æto place the cursor under the first digit
and Èor Çto set the number, then Æto the second digit, etc. Press Æor
üto proceed to the Menu Selections screen.
A new password can be stored by going to Special Functions/New
Password.
Page 9
DFM 5.0 Doppler Flow Meter
--Password----------
Password 0000
--24 hr log----------
>Date Feb. 12/2008
Total 0.000ft/s
Average 0.000ft/s
Maximum 0.000ft/s
Max Time 01:57:00
Minimum -1.046ft/s
Min Time 02:35:00
UNITS/MODE
From >Mode press the Æand then the Çor Èto select Flow or
Velocity. Flow mode displays the flow rate in engineering units (e.g.
gpm, litres/sec, etc.) Press the üto store your selection then the Èto the
next menu item and Æto enter.
From >Linear press the Ækey and then the Çor Èto select your units
of measurement. Press the üto store your selection.
Press the Èkey to move the >symbol to each subsequent menu item and
the üto save your selections.
Note: the volume selection "bbl" denotes U.S. oil barrel.
Press Åor üto return to the Menu Selections screen.
Page 10
DFM 5.0 Doppler Flow Meter
--Units/Mode--------
>Mode Flow
Linear in
Volume USG
Time min
--Units/Mode--------
Mode Flow
>Linear i
ft
m
mm
n
--Units/Mode--------
>Volume US
ft3
bbl
L
m3
IMG
IG
USMG
G
--Units/Mode--------
Mode Flow
Linear in
Volume USG
>Time se
day
hr
min
c
Indice
Altri manuali Greyline Instruments Strumento di misura
Greyline Instruments
Greyline Instruments MantaRay Manuale utente
Greyline Instruments
Greyline Instruments TTFM 1.0 Manuale utente
Greyline Instruments
Greyline Instruments A.1.2 Series Manuale utente
Greyline Instruments
Greyline Instruments AVFM 5.0 Manuale utente
Greyline Instruments
Greyline Instruments A.1.1 Series Manuale utente
Greyline Instruments
Greyline Instruments TTFM 1.0 Manuale utente
Greyline Instruments
Greyline Instruments PTFM 1.0 Manuale utente
Greyline Instruments
Greyline Instruments SLT32 Manuale utente
Greyline Instruments
Greyline Instruments PDFM 5.0 Manuale utente
Greyline Instruments
Greyline Instruments DFM-IV Manuale utente
Greyline Instruments
Greyline Instruments PDFM 5.1 Manuale utente
Greyline Instruments
Greyline Instruments AVMS 5.1 Manuale utente
Greyline Instruments
Greyline Instruments AVFM-II Manuale utente
Greyline Instruments
Greyline Instruments PORTAFLOW PT500 Manuale utente
Greyline Instruments
Greyline Instruments SFM 6.1 Istruzioni per l'installazione
Greyline Instruments
Greyline Instruments OCF 5.0 Manuale utente
