H3C S12500 Series Manuale utente
H3C S12500 Routing Switch Series
Quick Start Guide
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6PW101-20120508
Copyright © 2011-2012, Hangzhou H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot, Neocean, NeoVTL,
SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT,
XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,
Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage,
use, and disposal of this product must meet the applicable national laws and regulations.
i
Contents
Quick start guide·························································································································································· 1
Preparing for installation ··················································································································································1
ESD prevention ·························································································································································1
Examining the installation site·································································································································1
Installation tools and accessories ···························································································································2
Installing the switch ···························································································································································2
Installing the switch in a rack··································································································································2
Grounding the switch···············································································································································5
Installing the power modules···································································································································6
Installing a fan tray ··················································································································································8
Installing a card························································································································································9
Connecting power cords ······································································································································ 12
Verifying the installation ······································································································································· 15
Logging in to the switch················································································································································· 15
Connecting the console cable······························································································································ 15
Powering on the switch········································································································································· 16
Obtaining documentation ············································································································································· 17
Index ···········································································································································································18
1
Quick start guide
NOTE:
This quick start guide provides basic instructions for installing an S12500 routing switch. For more
detailed installation procedures, see
H3C S12500 Routing Switch Series Installation Guide
.
Preparing for installation
ESD prevention
To prevent the electronic components from being damaged by the electrostatic discharge (ESD), always
wear an ESD-preventive wrist strap when you touch the switch, cards, or ICs, and make sure that the wrist
strap is well grounded.
Figure 1 Attaching an ESD-preventive wrist strap
Examining the installation site
The H3C S12500 Routing Switch Series can only be used indoors. To make sure that the switch works
properly and to prolong its service lifetime, the installation site must meet the load-bearing, temperature,
2
humidity, cleanness, EMI, grounding, power module, and space requirements. For more information, see
H3C S12500 Routing Switch Series Installation Guide:
Installation tools and accessories
Installing the switch
Figure 2 Installation flow
Installing the switch in a rack
Check before installation
Before installation, make sure that the bottom edge of the slide rails or rack shelf aligns with the middle
of the narrower metal area between holes.
Phillips screwdriver
(user-supplied)
Cage nut
(required)
End
Verify the installation
Start
Install the switch in a rack
Ground the switch
Install power supplies Install a fan tray Install cards
Connect the power cords
3
Figure 3 Installing the slide rails
(1) Middle of the narrower metal area between holes (2) 1 RU
Installing cage nuts
1. Align the mounting bracket with the left rack post, making sure that the bottom edge and the slide
rail are level. Mark the positions of the cage nuts on the rack post according to the installation
holes on the mounting bracket (each installation hole on the mounting bracket corresponds to one
cage nut).
2. Insert one edge of a cage nut into the hole.
3. Compress the other edge of the cage nut to push the cage nut fully into the hole.
4. Repeat steps 2 and 3 to install cage nuts to all the marked positions on the right rack post.
Figure 4 Installing the cage nuts
1
1
2
4
Installing the mounting brackets
Figure 5 Installing the mounting brackets (for the S12504)
Figure 6 Installing the mounting brackets (for the S12508/S12518)
Mounting the switch in the rack
1. Use several people to place the switch on the slide rails or rack shelf and slide the switch into the
rack until the mounting brackets on the switch touch the front rack posts.
2. Fix the mounting brackets to the cage nuts on the rack posts with mounting screws.
5
Figure 7 Installing the switch in a standard 19-inch rack
Grounding the switch
1. Remove the two grounding screws from the switch chassis.
2. Use the grounding screws to attach one end of the grounding cable to the chassis.
3. Connect the other end of the grounding cable to the grounding strip of the rack in the same way.
6
Figure 8 Connecting the grounding cable
Installing the power modules
NOTE:
H3C recommends that you install at least three power modules to one power frame.
Installing a DC power module
1. Rotate the power frame cover up with both hands.
2. Pull the clip at the bottom left corner of the power module to the left to open the power module
panel.
3. Insert the power module slowly into the slot until it is firmly seated in the slot.
4. Close the panel of the power module, press the clip to lock the power module in position, and
close the power frame cover.
7
Figure 9 Installing a power module
Installing an AC power module
To install an AC power module, install a PEM first, and then install the AC power module.
To install a PEM:
1. Loosen the screws on the filler panel of the PEM slot with a Phillips screwdriver to remove the filler
panel.
2. Insert a PEM slowly along the slide rails until it touches the backplane connector.
3. Use the M3 screws supplied with the PEM to fix the PEM to the switch chassis, and fasten the
screws with a Phillips screwdriver.
Altri manuali per S12500 Series
19
Indice
Altri manuali H3C Interruttore
H3C
H3C S5560X-30C-EI Manuale utente
H3C
H3C LS-3100-16TP-EI-H3-A-O Manuale utente
H3C
H3C WX3000 Series Manuale utente
H3C
H3C S6520X-30QC-EI Manuale utente
H3C
H3C S10500 Series Manuale utente
H3C
H3C S3610 Series Manuale utente
H3C
H3C S5830V2 series Manuale di installazione
H3C
H3C S5150-EI Series Manuale utente
H3C
H3C S5830V2 series Manuale utente
H3C
H3C S5120-EI Series Manuale di installazione
H3C
H3C S7500 Series Manuale utente
H3C
H3C S7500 Series Manuale utente
H3C
H3C S5120-EI Series Manuale utente
H3C
H3C S6850 Series Manuale utente
H3C
H3C S3610 Series Manuale utente
H3C
H3C S3100V2-52TP Manuale operativo e di manutenzione
H3C
H3C S10512 Manuale utente
H3C
H3C S5830V2 series Manuale utente
H3C
H3C S6850 Series Manuale utente
H3C
H3C S12501X-AF Manuale utente
